BISSELL 69P3-E- Manuals

1. w w w . b i s s e l l . c o m A ssembly The only tool you’ll need to assemble your vacuum cleaner is a Phillips screwdriver. Attach handle to vacuum 1. Locate the handle and cord wrap. Remove the screw packet taped to the handle. 2. Stand the vacuum upright and from the rear of the unit, slide th...

w w w . b i s s e l l . c o m O perations 6 Power switch The Power Switch is located on the left side of the vacuum. Push the rocker switch “ON” (I) to vacuum, and “OFF” (O) when cleaning is complete. Handle positions Press the handle release pedal, located on the lower left side of the vacuum, with...

w w w . b i s s e l l . c o m 7 O perations Special on-board tools Your vacuum is not only a powerful carpet and rug cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools.1. Raise the handle to the upright position. 2. Grasp the hose wand handle to separa...

w w w . b i s s e l l . c o m O perations 8 Power cord usage 1. To use your vacuum, remove the cord and plug it into an electrical outlet. For your convenience, there is a quick release cord wrap for easy cord remov- al. There is also a cord clip that is part of the upper cord wrap where you can att...

w w w . b i s s e l l . c o m 9 M aintenance and care Emptying the dirt container The dirt container should to be emp- tied before the dirt reaches the “Full” line on the container.1. Unplug the vacuum from electrical out- let. 2. Slide the Lock ‘n Seal Lever to the “Unlock” position. 3. Grasp handl...

w w w . b i s s e l l . c o m M aintenance and care 10 You should check your vacuum cleaner’s rotating floor brush and drive belt regu- larly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hampe...

w w w . b i s s e l l . c o m 11 M aintenance and care Replace drive belt continued 3. Place new drive belt over motor pulley and loop other end over rotating floor brush in the space between the bristles. NOTE: It is important that you use only genuine BISSELL replacement belts. Generic belts may n...

w w w . b i s s e l l . c o m M aintenance and care 12 3. Remove the brush from the belt and clean debris. 4. Replace the brush inside the belt and place ends into slots on sides as shown. 5. Reposition top cover making sure to line up inside tab at the front with the open- ing on the cover. Twist c...

w w w . b i s s e l l . c o m 13 M aintenance and care T roubleshooting Vacuum cleaner won’t run Possible causes Remedies 1. Vacuum cleaner is not plugged in 1. Check electrical plug 2. Damaged power cord 2. Replace as necessary by an authorized service representative. Vacuum cleaner and tools won’t...

w w w . b i s s e l l . c o m T roubleshooting R eplacement parts A ccessories 14 Item Part No. Part Name 1 303-1120 Style 7/9/10/12/14 Drive Belt (2-Pack) 2 203-1603 Headlight Bulb 3 203-1283 Wide Window Foot Brush Roll (gray) 4 203-1073 Style 7/8/14 Pre-Motor Foam Filter 5 203-6608 Style 8/14 HEPA...

This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post a...

©2010 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 110-4311 Rev 11/10 Visit our website at: www.bissell.com B ISSELL consumer services w w w . b i s s e l l . c o m 16 If your BISSELL product should require service: Call BISSELL Consumer Services at ...