BISSELL 6 3 9 0- Manuals

5 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 the only tool you’ll need to assemble your vacuum cleaner is a phillips screwdriver. Attach handle to vacuum 1 . Locate the handle and cord wrap. Remove the screw packet taped to the cord wrap. 2. Stand the vacuum upright and from the rear of the...

Attach vacuum hose and tools 1. Line up the tabs on the base of the Twist ‘n Snap hose with the corresponding notches on the hose collar as shown. 2. Turn the Twist ‘n Snap hose to the left to lock the hose into place. 3. Connect the curved hose wand to the hose. Grasping the curved hose wand, slide...

Handle positions press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. 1. Upright – For storage and above floor cleaning with tools. 2. normal cleaning – Press handle release pedal once. Position used f...

Air flow indicator Select Models OnlyThe air flow Indicator tells you when the air flow in your vacuum is reduced due to dirty filters or a clog in the hose. The air flow indicator will remain green while the unit is running until the airflow is reduced by a clog or dirty filter. At that time, it be...

crevice tool: Use in tight narrow spaces. Extension Wand: Use with desired attachment for a longer reach. curved hose Wand: Use with desired attachment for a longer reach or for cleaning hard to reach places. turbobrush tM : Use rotating brush action for small areas such as stairs and upholstery. no...

to maximize your cleaning performance and extend the life of your vacuum, it is very important that you empty your dirt container and check and clean your filters frequently. perform the following maintenance steps: 1. Empty the dirt container when the dirt reaches the “Full” line on the container, ...

1. Unplug the vacuum from electrical outlet. 2. The pre-motor filter protects the motor from dirt particles. It is located in the slide out tray underneath the dirt container. If the filter becomes dirty, pull out the tray, lift out the foam filter pad and clean it. notE: the pre-motor filter may be...

14 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 M aintenance and care (continued) Maintaining TurboBrush the turbobrush should be checked regularly for clogs or debris wrapping around the brush.1. Unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, unscrew ...

15 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 M aintenance and care (continued) Clearing clogs low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor, check for clogs. 1. Unplug the vacuum from electrical outlet. 2. Empty dirt...

17 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 T roubleshooting Vacuum cleaner won’t run possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker in home 2. Check/replace fuse or reset breaker. Vacuum cleaner and tools won’t pick up dirt po...

18 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 For information about repairs or replacement parts, or questions about your warranty, call: bISSEll consumer Services 1-800-263-2535 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Canada Corporation Box 1003, N...

19 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 R eplacement parts - BISSELL Vacuum Replacement parts are available through bISSEll consumer Services, an authorized bISSEll Service centre or by visiting our website. below is a list of common replacement parts. While not all of these parts may...

16 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 20 w w w . b i s s e l l . c a 8 0 0 . 2 6 3 . 2 5 3 5 W arranty If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by e-mail, telephone, or regular ...