BISSELL 3910 - Manuals

5 w w w . b i s s e l l . c o m The only tool you’ll need to assemble your vacuum cleaner is a Phillips screwdriver. Attach handle to vacuum 1 . Locate the handle and cord wrap. Remove the screw packet taped to the cord wrap. 2. Stand the vacuum upright and from the rear of the unit, slide the base ...

Attach vacuum hose and tools 1. Line up the tabs on the base of the Twist ‘n Snap hose with the corresponding notches on the hose collar as shown. 2. Turn the Twist ‘n Snap hose to the left to lock the hose into place. 3. Connect the curved hose wand to the hose. Grasping the curved hose wand, slide...

Handle positions Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. 1. Upright – For storage and above floor cleaning with tools. 2. Normal Cleaning – Press handle release pedal once. Position used f...

Clean filter indicator Select Models Only The clean filter indicator tells you when the airflow in your vacuum is reduced due to dirty filters or a clog in the hose. The clean filter indicator will remain green while the unit is running until the airflow is reduced by a clog or dirty filter. At that...

Crevice Tool: Use in tight narrow spaces. Extension Wand: Use with desired attachment for a longer reach. Curved Hose Wand: Use with desired attachment for a longer reach or for cleaning hard to reach places. TurboBrush ™ : Use rotating brush action for small areas such as stairs and upholstery. NOT...

To maximize your cleaning performance and extend the life of your vacuum, it is very important that you empty your dirt container and check and clean your filters frequently. Perform the following maintenance steps: 1. Empty the dirt container when the dirt reaches the “Full” line on the container, ...

1. Unplug the vacuum from electrical outlet. 2. The pre-motor filter protects the motor from dirt particles. It is located in the slide out tray underneath the dirt container. If the filter becomes dirty, pull out the tray, lift out the foam filter pad and clean it. NOTE: The pre-motor filter may be...

2 1 3 4 Check rotating floor brush and drive belt You should check your vacuum cleaners rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hamper its ab...

13 w w w . b i s s e l l . c o m M aintenance and care Replace drive belt 1. Unplug the vacuum from electrical outlet. 2. With rotating floor brush removed from vacuum cleaner (Steps 1-4 of check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley. Discard the old...

14 w w w . b i s s e l l . c o m M aintenance and care Maintaining TurboBrush The TurboBrush should be checked regularly for clogs or debris wrapping around the brush. 1. Unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, unscrew the two screws on the back of the...

15 w w w . b i s s e l l . c o m M aintenance and care Clearing clogs Low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor, check for clogs. 1. Unplug the vacuum from electrical outlet. 2. Empty dirt container. 3. Check upper tank fo...

16 w w w . b i s s e l l . c o m M aintenance and care Cleaning the upper tank 1. Unplug the vacuum from electrical outlet. 2. Remove the dirt container as instructed in "Empty Dirt Container" on page 10. 3. Using a short Phillips screwdriver, take off the separator plate by removing the two...

17 w w w . b i s s e l l . c o m T roubleshooting Vacuum cleaner won’t run Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug Vacuum cleaner and tools won’t pick up dirt Possible causes Remedies 1. Incorrect height adjustment 1. Adjust powerfoot to correct height 2. Hose ...

18 w w w . b i s s e l l . c o m B ISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other c...

19 R eplacement parts Item Part No. Part Name 1 32074 Style 7/9/10/12/14 Drive Belt (2-Pack) 2 203-1297 Headlight Bulb 3 203-1063 Crevice Tool 4 203-1228 Dusting Brush/Upholstery Tool 5 203-2302 TurboBrush, clear top with black brush roll 6 203-1022 Extension Wand 7 203-2303 Curved Hose Wand 8 203-2...

16 w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 20 w w w . b i s s e l l . c o m W arranty - BISSELL Momentum Cyclonic Bagless Vacuum ©2007 BISSELL Homecare, IncGrand Rapids, MichiganAll rights reserved. Printed in KoreaPart Number 603-2377Rev 2/07Visit our website at:www.bissell.com This w...