BISSELL 37Y8E- Manuals

w w w . b i s s e l l . c o m A ssembly 5 Your CleanView ® Reach assembles quickly and easily. The only tool you will need for assembly is a Phillips head screwdriver.1. Slide upper body onto lower body. 2. Secure with screws. 3. Attach hose wrap to upper handle by sliding it up the bottom of the ha...

w w w . b i s s e l l . c o m O perations 6 Special features Your BISSELL CleanView ® Reach is a home cleaning system that uses a combination of hand hot tap water, BISSELL cleaning formula, brush agitation and suction to safely clean carpets.DirtLifter ™ Powerbrush The DirtLifter PowerBrush is desi...

w w w . b i s s e l l . c o m 7 O perations 4. Pre-Treating (optional) Pre-treat stub- born stains and highly soiled carpet in hallways and other high-traffic areas. 4a. Generously spray BISSELL Tough Stain Precleaner evenly over soiled area. Caution: DO NOT OVER WET CARPET 4b. Wait 3-5 minutes befo...

w w w . b i s s e l l . c o m O perations 8 2a. Release collection tank latches (on each side) by pulling up from the bottom of latch and then out. 2b. Carefully remove the top of the tank by lifting up on the tank handle. 3. Carry collection tank to a toilet or sink. To empty, pour out contents usi...

w w w . b i s s e l l . c o m 9 O perations 6. Clean by pressing the spray trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the spray trigger to suction dirty water. Continue to clean in the area, working in small sections, u...

w w w . b i s s e l l . c o m O perations 10 Hard floor cleaning (Select models only) 1. Remove the collection tank (refer to steps 2a and 2b on page 8). 2. Attach the hard floor tool by hooking it into the front of the removable nozzle and rotate until it snaps firmly in place. 3. Replace the colle...

w w w . b i s s e l l . c o m 11 M aintenance and care Machine storage For best results, a few simple steps can assure your machine is well main- tained after your cleaning is complete.1. Wrap power cord around Quick Release Cord Wrap™ on side of the machine. 2. Wipe all surfaces with a soft cloth. ...

w w w . b i s s e l l . c o m T roubleshooting 12 Reduced Spray OR No Spray in Upright Mode Possible causes Remedies 1. Solution tank empty 1. Refill tank with water and formula 2. Lint screen on solution tank cap clogged 2. Soak solution tank cap in warm water and then rinse under running water Red...

w w w . b i s s e l l . c o m 13 R eplacement parts Below please find a list of common replacement parts. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Item Part No. Part Name 1 203-8116 Handle Assembly (includes screws) 2 2...

w w w . b i s s e l l . c o m A ccessories and formula 14 Item Part No. Part Name 1 203-6651 3” Tough Stain Tool 2 203-6652 Powered TurboBrush™ Hand Tool 3 203-6653 4” Upholstery Tool 4 203-6654 6” Stair Tool 5 203-6655 Spraying Crevice Tool 6 203-8113 Deep Reach™ Tool 7 203-5548 Hard Floor Tool, 8 ...

w w w . b i s s e l l . c o m 15 W arranty - BISSELL CleanView ® Reach This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, p...

w w w . b i s s e l l . c o m 16 B ISSELL consumer services ©2012 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 120-4420 Rev 9/11 Visit our website at: www.bissell.com Scotchgard is a trademark of 3M Microban ® is a registered trademark of Microban Pr...