Beckett Oil Burner - Manuals

Page 2 - Table of Contents; Feature; NOTICE

Page 2 RWB 6104 BAFG R02 Table of Contents Hazard Defi nitions and Owner’s Information ........................................................................................ 3 Information To Be Used Only By Qualifi ed Service Technicians General Information ...........................................

Page 3 - Thank you for purchasing a Beckett burner; mediately contact your qualifi ed service agency; Hazard Defi nitions; Indicates an imminently haz-; DANGER; Indicates a potentially; Indicates a potentially haz-; CAUTION; Within the boundaries of the hazard warning, there; Owner’s Responsibility; WARNING; carbon monoxide poisoning, soot or explosion.; Do NOT Alter the Original; Tampering with or altering the burner design; WARNING

RWB 6104 BAFG R02 Page 3 To the Owner: Thank you for purchasing a Beckett burner for use with your heating appliance. Please pay at-tention to the Safety Warnings contained within this instruction manual. Keep this manual for your records and provide it to your quali fi ed service agency for use in ...

Page 4 - Table 1 – Burner Specifi cations; General Specifi cations; Table 2 – Air Tube Combination (ATC) codes; Professional Service

Page 4 RWB 6104 BAFG R02 Table 1 – Burner Specifi cations Capacity ( Note 1 ) ‘F’ Head (AF & AFG)Firing rate range: .............. 0.40 – 3.00 GPH Input: ....................... 56,000 – 420,000 Btu ‘L1’ Head (AFG Only)Firing rate range: ..................0.40 - 1.10 GPH Input: ....................

Page 5 - Inspect/Prepare Installation Site; Failure to provide adequate air supply could se-; Failure to comply could result in impaired com-

RWB 6104 BAFG R02 Page 5 SK9475 Notice Special Requirements For recommended installation practice in Canada, refer to the latest version of CSA Standard B139 & B140. Concealed damage — If you discover damage to the burner or controls during unpacking, notify the carrier at once and fi le the app...

Page 6 - Burner head type; Prepare the Burner; Failure to comply could result in damage to the; Incorrect nozzles and fl ow rates; and potential fi re or asphyxiation hazards.

Page 6 RWB 6104 BAFG R02 Table 4. AFG Reduced Firing Rates (with LFRB) Burner head type Low Firing Rate Baffl e installed F0 up to 0.65 gph F3 or L1 up to 0.85 gph F4 or F6 up to 0.90 gph V1 up to 1.00 gph Prepare the Burner Low Firing Rate Baffl e The AFG Low Firing Rate Baf fl e (LFRB) reduces the...

Page 8 - Check/Adjust ‘Z’ Dimension for ‘F’ Heads; Burner Dimensions; Incorrect Adjustments could cause combus-; Adjust the ‘Z’ dimen-

Page 8 RWB 6104 BAFG R02 Check/Adjust ‘Z’ Dimension - ‘F’ heads 1. The important ‘Z’ dimension is the distance from the face of the nozzle to the fl at face of the head (or heat shield, if applicable). This dis- tance for F heads is 1- ⅛ ” (1- ⅜ ” if the air tube has a heat shield). The “Z” dimensio...

Page 10 - Mount burner on appliance; Failure to comply could cause Immediate pump; Fuel supply level with or above burner –; Damage to the fi lter or pump seals could cause

Page 10 RWB 6104 BAFG R02 The burner may be equipped with a single-stage fuel unit for these installations. Connect the fuel supply to the burner with a single supply line if you want a one-pipe system (making sure the bypass plug is NOT installed in the fuel unit.) Manual bleed-ing of the fuel unit...

Page 11 - Damage to the pump could cause impaired burn-; Do Not Use Tefl on Tape; Electrical shock can cause severe; Electrical Shock Hazard; Fuel supply below the level of the burner –; Always use fl are fi ttings.; Fuel line valve and fi lter –; Burner installed at jobsite

RWB 6104 BAFG R02 Page 11 Never use Te fl on tape on fuel oil fi ttings. Tape fragments can lodge in fuel line components and fuel unit, damaging the equipment and pre-venting proper operation.Use oil-resistant pipe sealant compounds. yy y Damage to the pump could cause impaired burn- er operation, ...

Page 12 - Control System Features; Figure 7. – Typical Burner Wiring

Page 12 RWB 6104 BAFG R02 7. RECYCLE. If the fl ame is lost while the burner is fi ring, the control shuts down the burner, enters a 60 second recycle delay, and then repeats the above ignition sequence. If fl ame is lost three times in a row, the control locks out to prevent cycling with repetitiou...

Page 13 - Start up burner/set combustion; Set combustion with instruments; Natural Draft Applications; Failure to follow these instructions; Explosion and Fire Hazard

RWB 6104 BAFG R02 Page 13 Start up burner/set combustion For R7184 primary controls, see Technician’s Quick Reference Guide, part number 61351 for special pump priming sequence.Prepare for combustion tests by drilling a ¼” sam-pling hole in the fl ue pipe between the appliance and the barometric dra...

Page 14 - Perform regular maintenance; Figure 8. Blower wheel assembly; Tampering with or making incorrect; Annual Professional Ser-

Page 14 RWB 6104 BAFG R02 Perform regular maintenance Check all wiring for secure connections or insula-tion breaks.Check the pump pressure and cutoff function.Check primary control safety lockout timing.Check ignition system for proper operation.Inspect the vent system and chimney for soot ac-cumul...

Page 15 - For best performance specify genuine; Beckett; replacement parts; Professional Maintenance

RWB 6104 BAFG R02 Page 15 For best performance specify genuine Beckett replacement parts Professional Maintenance SK9462 # Part No. Description 1 Burner Housing Assembly 2 Specify Air Band - Specify # of slots 4198 Screw, 10-24 x 1/2” 4150 Nut, 10-24 Square 3 Specify Air Shutter - Specify # of slots...

Page 16 - Limited; WARRANTY; BECKETT; CORPORATION

Page 16 RWB 6104 BAFG R02 Limited WARRANTY For Residential, Commercial and Specialty Burners The R. W. BECKETT CORPORATION (“Beckett”) warrants to persons who purchase its Beckett burners from Beckett for resale or for incorporation into a product for resale (“Customers”) that its equipment is free ...