Avenview SW-HDM3D-C5-8X8 - Manuals

Page 2 - Table of Contents

www.avenview.com 2 including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is stri...

Page 3 - Section 1: Getting Started; Important Safeguards; What the warranty does not cover; Safety Instructions

www.avenview.com 3 Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover  Any product, on which the serial number has been defaced, modified or removed. ...

Page 7 - Panel Description; Seven Segment LED Indicators:

www.avenview.com 7 1.7 Panel Description 1.7.1 SW-HDM3D-C5-8X8 Front Panel 1. Power: Power Control 2. Seven Segment LED Indicators: LED display for output ports and input channels 3. Front Panel Push Buttons: Front panel push buttons used to select the number of input source and display channel 4. I...

Page 8 - CHANNEL CONTROL

www.avenview.com 8 1.7.3 HDM3D-C5SW-R 1. IR INPUT: Plug in IR receiver. 2. +5V DC: Spare power jack for over 60m transmission when the RX may need external power to work. 3. HDMI SIGNAL: Plug in the CAT5 connected to the respective A/V SIGNAL port on the SW-HDM3D-C5-8X8 4. IR SIGNAL: Plug in the CAT...

Page 11 - IR Control Patch; IR Transmitter Cable

www.avenview.com 11 1.8 IR Control Patch IR Transmitter Cable IR Receiver Cable IR Main The default location for IR emitter extension cable to transmit all IR command signals received from any of the four remote receivers to all of the HDMI sources. IR1 IR emitter extension cable connected here can ...

Page 13 - Operation and IR Control

www.avenview.com 13 1.10 Operation and IR Control 1.10.1 Source Side 1.10.1.1Method A: Push Button 1. Use the “  ” or “—“ channel button on output port to select which port to be changed. “  ”: change selected output port in ascending order “—“: change selected output port in descending order 2. P...

Page 15 - RS232 Serial Port Control

www.avenview.com 15 1.11 RS232 Serial Port Control Scan: Press Scan button, the machine will scan the all com port and show them. Select the RS232 serial port connected to the machine. And set device ID 255 is for all device. Only the same device id or 255 can get the command you sent. Press OK. Get...

Page 16 - Fast select; One by one setting

www.avenview.com 16 Linkage: Press Linkage button to read back all status Open / Close : Press this button to Close or Open COM Port. Mapping Button: Select All Output: Select “set all output”, then select the source on main menu. You can quickly set all output to the same source. Unselect All Outpu...

Page 17 - Group setting

www.avenview.com 17 Group setting First select output ports one by one. Then select the input source. The selected output ports change the setting at the same time. By using Terminal: Baud rate: 9600 Data length: 8bit Parity check: No Stop bit: 1 1.11.1RS232 Commands COMMAND ACTION COMMAND ACTION CO...

Page 19 - Notice

www.avenview.com 19 Notice 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI/HDMI EDID information. 2. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz LAN cable and ASTRODESIGN Video Signal Gen...