Avenview SW-HDM3D-C5-4X4 - Manuals

Page 2 - Table of Contents

www.avenview.com 2 including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is stri...

Page 3 - Section 1: Getting Started; Important Safeguards; What the warranty does not cover; Safety Instructions

www.avenview.com 3 Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover  Any product, on which the serial number has been defaced, modified or removed. ...

Page 7 - Panel Description

www.avenview.com 7 1.7 Panel Description 1.7.1 SW-HDM3D-C5-4X4 Front Panel 1. Port 1-4 SELECT: Push-in button for selecting input channel 2. Port 1-4: Input source channels mapping LED for each output channel 3. HP 1-4: Connection status indicator LED for each output channel 4. INPUT: Input source i...

Page 8 - CHANNEL CONTROL

www.avenview.com 8 1.7.3 HDM3D-C5SW-R 1. IR INPUT: Plug in IR receiver. 2. +5V DC: Spare power jack for over 60m transmission when the RX may need external power to work. 3. HDMI SIGNAL: Plug in the CAT5 connected to the respective A/V SIGNAL port on the SW-HDM3D-C5-4X4 4. IR SIGNAL: Plug in the CAT...

Page 10 - Normal Operation Mode

www.avenview.com 10 1.7.5 SW Main Dip Switch for Firmware Update DIP Switch Position PIN # 1 PIN # 2 PIN # 3 PIN # 4 Normal Operation Mode 6 OFF  OFF  ON  OFF  Firmware Update Mode 7 ON  ON  OFF  OFF  6 Factory default for SW Main is pin#1-OFF[  ], pin#2-OFF[  ], pin#3-ON[  ], & pin#4...

Page 11 - IR Control Patch; IR Transmitter Cable

www.avenview.com 11 1.8 IR Control Patch IR Transmitter Cable IR Receiver Cable IR Main The default location for IR emitter extension cable to transmit all IR command signals received from any of the four remote receivers to all of the HDMI sources. IR1 IR emitter extension cable connected here can ...

Page 12 - Power on all HDMI sources

www.avenview.com 12 1.9 Installation (SW-HDM3D-C5-4X4) To setup Avenview SW-HDM3D-C5-4X4 follow these steps for connecting to a device: 1. Connect all sources to HDMI Inputs on the 4X4 HDMI over CAT5 Matrix Switch (SW-HDM3D-C5-4X4) 2. Connect each DDC output on the SW-HDM3D-C5-4X4 to respective DDC ...

Page 13 - Operation and IR Control

www.avenview.com 13 1.10 Operation and IR Control 1.10.1 Source Side 1.10.1.1Method A: Push-in Button Push the red switch button on output port to select which port to be changed. 1.10.1.2Method B: IR Remote Control Choose the output port you want to make channel switch from OUT1 to OUT4 then press ...

Page 14 - RS232 Serial Port Control

www.avenview.com 14 1.11 RS232 Serial Port Control Scan: Press Scan button, the machine will scan the all com port and show them. Select the RS232 serial port connected to the machine. And set device ID 255 is for all device. Only the same device id or 255 can get the command you sent. Press OK. Get...

Page 15 - Fast select; One by one setting

www.avenview.com 15 Linkage: Press Linkage button to read back all status Open / Close : Press this button to Close or Open COM Port. Mapping Button: Select All Output: Select “set all output”, then select the source on main menu. You can quickly set all output to the same source. Unselect All Outpu...

Page 16 - Group setting; bit

www.avenview.com 16 Group setting First select output ports one by one. Then select the input source. The selected output ports change the setting at the same time. By using Terminal: Baud rate: 9600 Data length: 8bit Parity check: No Stop bit: 1 1.11.1RS232 Commands COMMAND ACTION COMMAND ACTION CO...

Page 17 - Environmental

www.avenview.com 17 Section 2: Specifications Item Description Units SW-HDM3D-C5-4X4 HDM3D-C5SW-R Unit Description 4X4 HDMI Matrix Switch with 3D over CAT-5 with IR Pass-Through HDMI Matrix Switch with 3D Receiver HDMI Compliance Support HDMI Deep Color & full 3D HDCP Compliance Yes Video Bandwi...

Page 18 - Notice; retrieve and provide DVI/HDMI EDID information.

www.avenview.com 18 Notice 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI/HDMI EDID information. 2. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz LAN cable and ASTRODESIGN Video Signal Gen...