Avenview RTERM-17T-16 - Manuals

Page 2 - Table of Contents

www.avenview.com 2 Table of Contents Section 1 – Getting Started .................................................................................................................... 5 1.1 Important Safegaurds ..............................................................................................

Page 5 - Section 1 – Getting Started; Important Safegaurds; What the warranty does not cover

www.avenview.com 5 Section 1 – Getting Started 1.1 Important Safegaurds Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover  Any product, on which the serial number has been defaced, modified or removed. ...

Page 6 - Safety Instructions; Regulatory Notices Federal Communications Commission (FCC)

www.avenview.com 6 1.2 Safety Instructions  Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.  Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with temperatures not exceeding 40° C (104° F).  When ...

Page 7 - Package Contents

www.avenview.com 7 1.4 Package Contents 1 Console terminal LCD keyboard drawer x 1 pc 2 RJ45 DB9 female adapter x 1 pc 3 RJ45 DB9 male adapter x 1 4 Fasteners for rear L-brack x 4 pcs 5 330mm rear mounting L-bracket x 1 pair RTERM-17T-16 mounting depth-adjustable from 320mm to 920mm 6 User manual x ...

Page 8 - Cat 5 Cable

www.avenview.com 8 1.5 Before Installation  It is very important to locate the console terminal LCD Keyboard Drawer in a suitable environment.  The surface for placing and fixing the Console Terminal Drawer should be stable and level or mounted into a suitable cabinet.  Make sure the place has go...

Page 9 - Structure Diagram

www.avenview.com 9 1.8 Structure Diagram 1 Carry handle to release the 2-pt lock 2 2-point lock 3 LCD interchangeable module kit 4 LCD membrane 5 Adjustable rear mounting L-bracket 6 Micro switch for screen auto power off 7 Serial port Status LED 8 Keyboard interchangeable module kit

Page 10 - Installation; Figure 1; Figure 2

www.avenview.com 10 1.9 Installation Figure 1  Install each rear L-bracket using two fasteners shown in Figure 1 .  Leave the fasteners slightly loose Figure 2  Measure the front and rear mounting depth of the rack.  Align each rear L-bracket to a suitable length and tighten the fasteners shown ...

Page 11 - How to Use “NCP” Series LCD Keyboard Drawer

www.avenview.com 11 1.10 How to Use “NCP” Series LCD Keyboard Drawer Figure 4 Gently pull the tab toward the front of the LCD, shown in Figure 4 Figure 5 Flip up the LCD to a suitable angle, as shown in Figure 5 Figure 6 Operate the LCD keyboard drawer, as shown in Figure 6

Page 12 - How to Use the Slides; Figure 7; Figure 9

www.avenview.com 12 1.11 How to Use the Slides Figure 7 A white arrow release button is located on the outside of each slide, as shown in Figure 7 Figure 8 Push the white arrow button on either side of the LCD keyboard drawer to unlock, as shown in Figure 8. Avoid pressing the red button located on ...

Page 13 - How to Install “One Man” Installation Slides

www.avenview.com 13 1.12 How to Install “One Man” Installation Slides 1.12.1 Package Contents 1 Mounting bracket x 2 pcs 2 Front mounting ear (left & right ) x 2 pcs 3 Support bracket x 4 pcs 4 M6 cage nut x 8 pcs 5 M6 washer x 8 pcs 6 M6*15mm screw x 8 pcs 7 M3.2*4.5mm screw x 14 pcs 1.12.2 Ins...

Page 14 - Install into Rack

www.avenview.com 14 1.12.3 Install into Rack  Attach the mounting brackets to vertical mounting rails.  Leaving the screws slightly loose.  Attach left and right front mounting ears to vertical rails.  Tighten the screws.  Attach the support brackets to chasis with M3.2*4.5mm screws x 6 pcs  I...

Page 15 - Section 2: How to Connect Console Terminal LCD Keyboard Drawer; On-screen Display Operation

www.avenview.com 15 Section 2: How to Connect Console Terminal LCD Keyboard Drawer 2.1 On-screen Display Operation

Page 16 - Membrane; Power ON

www.avenview.com 16 2.2 Membrane 2.2.1 Power ON Turn off all devices / servers and Cat5 IP serial console Make sure all cables / connectors are properly connected 2.2.2 Front Panel – Port LD Indications 16 ports Power Red Power on indication Link Orange 10BaseT Ethernet Connection Green 100BaseT Eth...

Page 17 - Configuring the Local Console; Switch on the power on the rear of RTERM-17T-16; Entering SETUP; Hold down the; Alt; key and then depress the; Esc; key to enter the SETUP mode.

www.avenview.com 17 2.3 Configuring the Local Console Switch on the power on the rear of RTERM-17T-16 2.3.1 Entering SETUP Hold down the Alt key and then depress the Esc key to enter the SETUP mode. When you enter SETUP mode, and text on the screen temporarily disappears, and the main SETUP director...

Page 18 - Saving and Exiting SETUP; Spacebar; YES

www.avenview.com 18 2.3.2 Saving and Exiting SETUP The first menu seen when entering SETUP mode serves as a directory to the other SETUP menus. When you depress F12 to exit Setup, you will return to this main directory and be given the option of saving your selections. The highlighted field at the r...

Page 19 - Complete the configuration and select to confirm

www.avenview.com 19 The 16-port serial console drawer with serial-to-serial local access function which the data transfer can be between one designated serial port (ESP) and one of the other serial ports.  Select the access port and configure each setting & type in the value for Inactivity time...

Page 21 - Changing Operating Parameters

www.avenview.com 21 2.4 Changing Operating Parameters To select one of the setup menu’s shown, press the indicated function key.  The screen for that menu appears with the name highlighted.  The fields in the middle of the screen, indicate the parameters that you can change in that menu.  The top...

Page 26 - Netmask; Gateway

www.avenview.com 26 You can program a message of up to 20 characters to identify the terminal to the computer. Enter the message at the cursor position. Correct errors by pressing to delete characters or to clear the message. CONCEAL hides the answerback message, so it is not displayed in SETUP mode...

Page 28 - Color Palettes Table; Palette

www.avenview.com 28 2.4.1 Color Palettes Table Palette Display Attribute Foreground Color Background Color 0 Normal Reverse ( or Blank) *1 Intensity *2 Intensity *2 and reverse (or Blank) *1 Underline Underline and reverse (or Blank) *1 Underline and Intensity *2 Underline, Intensity *2 and reverse ...

Page 30 - Local Keyboard Command in Native Mode; Commands

www.avenview.com 30 2.5 Local Keyboard Command in Native Mode Commands Key Sequence by keyboard Style Enhanced PC Toggle CAPS LOCK on/off CAPS LOCK Toggle NUM LOCK on/off NUM LOCK Put terminal in SETUP mode ALT ESC Partially reset terminal, including communication unlock keyboard, turn off all print...

Page 31 - Connector Pin Assignment; Console port & serial port ping assignment; Pin; Command Guide

www.avenview.com 31 2.6 Connector Pin Assignment Console port & serial port ping assignment Pin Signal Direction 1 DSR In 2 RTS Out 3 GND - 4 TxD Out 5 RxD In 6 DSR 7 CTS In 8 DTR Out 2.7 Command Guide Commands Supported in ASCII Personalities Below table lists all the ASCII commands recognized ...

Page 43 - Device Setup; Setup the IP address from Ethernet Port; The Operation procedures are as follows:; Access IP Serial Console

www.avenview.com 43 2.8 Device Setup 2.8.1 Setup the IP address from Ethernet Port In addition to VT100 interface, we also provide a Network Setup Software tool (IPCS Setup) fro the network settings to the IP Serial Console. The Operation procedures are as follows:  Run the software tool IpcsSeeker...

Page 44 - User Name; Web Management Interface

www.avenview.com 44 There are Two levels of access privileges. User Name Default Password Access Privileges root root Full access (user define) (user define) Limited access to Serial Port The administrator can add or remove a user easily via the web pages of System administrations. 2.8.2 Web Managem...

Page 45 - Section 3: IP Setting; IP Configuration

www.avenview.com 45 Section 3: IP Setting 3.1 IP Configuration User can do the network IP settings via V-100 or web pages. This chapter describes the usage of web pages. The default IP settings are as follows. 3.1.1 IP Configuration The IP serial console requires a valid IP address to operate within...

Page 46 - IP Filtering; Specified Host Range

www.avenview.com 46 Secondary SMTP configuration is also provided so that mail can be delivered even when the primary SMTP server fails. Only when the primary SMTP server fails, the secondary SMTP server will be tried for mail delivery. 3.2 IP Filtering 3.2.1 IP Filtering The IP filtering function k...

Page 48 - Web Server Configuration

www.avenview.com 48 In the example above, no host is allowed to connect to the IPCS through http (port 80) by the #3 rule but the hosts whose subnet is 192.168.1.x is allowed by the #1 rule and 192.168.2.x by the rule #2. So, only the hosts which belong to the subnet 192.168.1.x or 192.168.2.x can a...

Page 51 - Radius Server Configuration; Section 4: Serial Port Configuration; Serial Port Configuration

www.avenview.com 51 Radius Server Configuration Section 4: Serial Port Configuration 4.1 Serial Port Configuration Under the Serial Port heading, click Configuration will show the list of port summary as below.

Page 54 - Console Server Mode:; Listening TCP port number

www.avenview.com 54 Note:  The Power Control Mode is available in port #1 only.  The last port (e.g. Port#16 of IPCS-16) can also be used as External ESP (Entry Serial Port) in Serial-to-Serial operation mode. Refer to the section Serial-to-Serial Function for details. Console Server Mode: Configu...

Page 57 - Connection

www.avenview.com 57 If Port logging option is enabled, the user can let the IP serial console to search a defined keyword from the port logging data and send an email to an administrator by Port event handling configurations. Each reaction can be configured individually upon each keyword. Reaction c...

Page 59 - Serial Power Control Function

www.avenview.com 59 4.3 Serial-to-Serial Function 4.2.1 Serial-to-Serial Function The web page also gives read-only settings of Serial-to-Serial function, it will auto-changed upon the setting change on VT100 console. Click Cancel will refresh the values. 4.2.2 Serial Power Control Function The Seri...

Page 61 - Section 6: System Settings; System Administration; Check the users at the User Administration Screen

www.avenview.com 61 Section 6: System Settings 6.1 System Administration 6.1.1 User Administration At startup of the AP, the system will prompt user to enter the password to access to the system. The administrator can add or remove a user easily via the web pages. There are two levels of access priv...

Page 64 - Date and Time

www.avenview.com 64 6.2 Date and Time The IPCS maintains current date and time information. The IPCS clock and calendar settings are backed up by internal battery power. The user can change the current date and time. There are two methods of date and time settings. The first is to use the NTP server...

Page 65 - Firmware Upgrade; Prepare Upgrade Environment

www.avenview.com 65 6.3 Firmware Upgrade Firmware can be easily upgraded via web page. This section describes the upgrade procedures. *Pls contact you the latest firmware version is available on the web site. 6.3.1 Prepare Upgrade Environment 1 Need to obtain a TFTP server software program. 2 Startu...

Page 67 - Section 7: Operations

www.avenview.com 67 Section 7: Operations 7.1 On-screen Display Operation 17" LCD membrane Membrane Switch Function Power light Green = On Orange = Power saving Power on / off LCD Display the OSD menu Scrolls through menu options and adjusts the displayed control Exit the OSD screen Shortcut key...

Page 68 - RESET

www.avenview.com 68 7.2 On-screen Menu BRIGHTNESS / CONTRAST Brightness Adjust background black level of the screen image. Contrast Adjust the difference between the image background (black level) and the foreground (white level) AUTO ADJUST Auto Adjust Fine tunes the video signal to eliminate wavin...

Page 70 - Section 8: Specifications

www.avenview.com 70 Section 8: Specifications Item Description Form Factor 1U rack mounting on slide-out rails LCD Manufacturer Diagonal Size 17" TFT Max. Resolution 1280 x 1024 (Native) Brightness (cd/m²) 300 Color Support 16.2 Mil. Contrast Ratio (typ.) 700:1 Viewing Angle (H/V) 150˚ x 135˚ Di...

Page 71 - N Keyboard with full numerical pad; PS/2 or USB Connection; DC Power Option; Model; Input Voltage; Input Current; Output Voltage; Efficiency

www.avenview.com 71 1.13 Keyboard & Mouse N Keyboard with full numerical pad  104 Keys (US / European / Chinese / Korean layout)  106 Keys (Japan layout)  PS/2 or USB Connection 1.14 DC Power Option Model 12V 24V 48V Input Rating Input Voltage 12 Volt 24 Volt 48 Volt Input Rage 9 ~ 18V 18 ~ 3...

Page 72 - Section 9: Troubleshooting; The membrane button power light is not ON; How does the CAT5e cable connect to the servers?

www.avenview.com 72 Section 9: Troubleshooting 1. The membrane button power light is not ON Press the power On /Off on LCD membrane button to check if the monitor is in the ON mode. Check the power cord is properly connected to the LCD keyboard drawer and power outlet. 2. Screen image is not centere...

Page 74 - Section 10: Dimensions

www.avenview.com 74 Section 10: Dimensions Model Product Dimension (W x D x H) Package Dimension (W x D x H) Net Weight Gross Weight RTERM-17T-16 442 x 650 x 44 mm 17.4 x 25.6 x 1.75 in 589 x 856 x 168 mm 23.2 x 33.7 x 6.6 in 16kg 35lb 22kg 48lb