Asus AAM6020BI-T4- Manuals

AAM6030BI User Manual 3. Getting Start This chapter provides basic instructions for connecting the CPE to a computer or a LAN and to the Internet via ADSL. f Part 1 provides instructions to set up the hardware. f Part 2 describes how to configure Internet properties on your computer(s). f Part 3 sho...

AAM6030BI User Manual 4. Setting up your CPE This section will guide you through your CPE’s configuration. The CPE is shipped with a standard default bridge configuration; for most users, you may want to change the CPE from a bridge to a router. 4.1 Log into your CPE To configure your CPE, open your...

AAM6030BI User Manual Figure 2 (Home page) 4.3 Setup To setup your CPE with a basic configuration, from the Home page, select Setup. Figure 3 illustrates the setup page. The page is broken into two subsections the WAN configuration and the LAN configuration. Before configuring the router, there are ...

AAM6030BI User Manual 4.3.1 Wide Area Network connection On the other side of the router is where your Wide Area Network (WAN) connection; also referred to as a broadband connection. This WAN connection is different for every WAN supplier. Most of the configuration you will perform will be in this a...

AAM6030BI User Manual and VCI settings; your DSL service provider or your ISP will supply these; in this case the DSL service provider is using 0,35. Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not provide this information. Figure 4 (Bridge Conn...

AAM6030BI User Manual c. On-Demand: Enables on-demand mode. The connection will disconnect if no activity is detected after the specified idle timeout value. d. Idle Timeout: Specifies that PPPoA connection should disconnect if the link has no activity detected for n seconds. This field is used in c...

AAM6030BI User Manual 4.4.1.4 DHCP Connection Setup Dynamic Host Configuration Protocol (DHCP) allows the CPE to automatically obtain the IP address from the server. This option is commonly used in situations where IP is dynamically assigned and is not known prior to assignment. To configure the CPE...

AAM6030BI User Manual 4.5 Configuring the LAN By default, your CPE has DHCP server (LAN side) enabled. If you already have a DHCP server running on your network, you must disable one of the two DHCP servers; if you plug a second DHCP server into the network, you will experience network errors and th...

AAM6030BI User Manual Figure 10 (Example of a DHCP Relay configuration) By turning off the DHCP server and relay the network administrator must carefully configure the IP address, Subnet Mask and DNS settings of every computer on your network. Do not assign the same IP address to more than one compu...

AAM6030BI User Manual 4.6.7 Multicast/IGMP Snooping Multicasting is a form of limited broadcast. UDP is used to send datagrams to all hosts that belong to what is called a "host group." A host group is a set of zero or more hosts identified by the same destination IP address. The following s...

AAM6030BI User Manual Figure 16-2 (IGMP SNOOPING) 4.6.8 Static Routing If the CPE is connected to more than one network, you may need to set up a static route between them. A static route is a pre-defined pathway that network information must travel to reach a specific host or network. You can use s...

AAM6030BI User Manual Figure 20 (Ping test) 4.7.6 Modem Test The Modem Test is used to check whether your Modem is properly connected to the WAN Network. This test may take a few seconds to complete. To perform the test, select your connection from the list and press the Test button. Before running ...

AAM6030BI User Manual 4.8.6 System Log You can display the CPE’s log by going to the Home screen, under the Status title, click System log. From here you can view all logged information. Depending upon the severity level, this logged info will generate log reports to a remote host (if remote logging...

AAM6030BI User Manual 5. Appendix A: Troubleshooting Below is a list of commonly asked questions. Before calling technical support, please look through these issues to see if they help solve your problem. 5.1 The CPE is not functional 1. Check to see that the power LED is green and than the network ...

AAM6030BI User Manual 5.4 The DSL Link LED continues to blink but does not go solid 1. This means that the DSL line is trying to train but for some reason it cannot establish a valid connection. The main cause of this is that you are too far away from the central office. Contact your DSL service pro...

AAM6030BI User Manual 6. Router terms What is a firewall? A firewall is protection between the Internet and your local network. It acts similarly to the firewall in your car, protecting the interior of the car from the engine. Your car's firewall has very small opening that allow desired connections...