Asko D3mmmXL - Manuals - manualsarea.com

Page 2 - Tip Guards

Page 2 T O O L S T O O L S T O O L S T O O L S T O O L S 1) Phillips No. 2 screwdriver 2) Flat blade screwdriver 3) Torx screwdriver size T 20 4) Adjustable wrenches (if you use copper fittings) 5) Open-ended wrench (1/2" [12 mm] or 5/8" [16 mm]) 6) Tape measure 7) Spirit level 8) Electric d...

Page 4 - Plumbing connections must comply with; ” clearance; Drain hose boot; Water supply; Electrical cord

Page 4 WARNING! Plumbing connections must comply with applicable sanitary, safety and plumbing codes in yourarea. The machine can be connected to either a hot or coldwater supply. If a cold water supply is used, the washingtimes will be longer but the performance will not beaffected. The dishwasher ...

Page 5 - DRAIN CONNECTIONS

Page 5 ASKO provides a 7/8” (22 mm) corregated drain hosewhich is connected to the back of the unit to form a highloop. If additional drain hose is the added hose andany joints or connections can be no smaller than 7/8"O.D. Stock. NOTE: Do not use any fittings anywhere in the drainline that are ...

Page 6 - M a k e s u r e t h e w a t e r s u p p l y l i n e ,; immediately

Page 6 WARNING! B e f o r e w o r k i n g o n w i r i n g f o r a n y e l e c t r i c a l a p p l i a n c e , b e s u r e t h e e l e c t r i c a l p o w e rh a s b e e n t u r n e d o f f a t t h e b r e a k e r / f u s e b o x . WARNING! D i s c o n n e c t e l e c t r i c a l p o w e r s u p p l ...

Page 7 - Be careful of sharp edges.

Page 7 WARNING! Make sure you put the protective slides on the legs toprevent damaging the floor when you slide the unitinto place (see page 6). 1. P o s i t i o n t h e m a c h i n e i n f r o n t o f t h e c a b i n e topening. 2. Make the height adjustment while the dishwasheris in front of the o...

Page 8 - Turn on the water supply and check for leaks.; Before starting this procedure, be sure

Page 8 TESTING FOR LEAKS TESTING FOR LEAKS TESTING FOR LEAKS TESTING FOR LEAKS TESTING FOR LEAKS 1. Turn on the water supply and check for leaks. 2. Turn the power on at breaker/fuse box and test the dishwasher operation by running a Rinse cycle.(This should take about four minutes.) 3. Turn off the...

Page 9 - M o u n t i n g

Page 9 Now that all the connections are made and the machineis in place under the cabinet, you should make the finalheight adjustment. 1. Yo u s h o u l d s e t t h e rear foot first. To dot h i s , u s e ascrewdriver to rotatet h e a d j u s t i n g s c r e won the bottom front ofthe machine. Turn ...

Page 11 - Custom panel extends to cabinet top

Page 11 4-inc 4-inc 4-inc 4-inc 4-inch h h h h T T T T Toe Kic oe Kic oe Kic oe Kic oe Kick Installa k Installa k Installa k Installa k Installations tions tions tions tions Custom panel extends to cabinet top One installation option for a 4” toe kick is to extend thecustom panel to the cabinet top ...

Page 12 - installing 4; I N D E X

Page 12 A A A A A Access holes 3 C C C C C Cabinet, fastening unit to 9 Cabinet opening dimensions 3 Connecting to water supply 9 Corner installation 4 Cosmetic damage 2 D D D D D Dimensions, unit 3 Door panels, fully-integrated 11 Door springs, adjusting 10 Drain connections 4 E E E E E Electrical ...