Ariens 029-034 - Manuals

Ariens 029-034 – Manual in PDF format online.

Manuals:

Manual

Manual Ariens 029-034

Summary

Page 2 - TABLE OF CONTENTS

2 Section 1 - Introduction . . . . . . . . . . . . . . . . . 1-3 1.1 The Manual . . . . . . . . . . . . . . . . . . . . . . . 1-3 1.2 Service and Replacement Parts . . . . . . . 1-3 1.3 Product Registration . . . . . . . . . . . . . . . . 1-3 1.4 Unauthorized Replacement Parts . . . . . . 1-3 1.5 Di...

Page 3 - SERVICE AND REPLACEMENT PARTS; SECTION 1 - INTRODUCTION

1 - 3 1.1 THE MANUAL It is the purpose of this manual to provide complete instructions for service, maintenance, disassembly, repair, and installation of the mechanical components for the 932 Snow-Thro. Dealer trained service personnel should use this manual as a supplement to and reminder of the tr...

Page 4 - Personal Safety Is Involved!; PRACTICES AND LAWS

2 - 4 2.1 SAFETY ALERTS Look for these symbols to point out important safety precautions. They mean: Attention! Personal Safety Is Involved! Become Alert! Obey The Message! 2.2 SIGNAL WORDS The safety alert symbol is used in decals on the unit and with proper operation procedures in this manual. The...

Page 6 - Storage; Transport

2 - 6 Before maintenance, adjustments, or service (except where specifically recommended), shut off engine. Allow hot parts to cool. Keep unit free of dirt, stones, and other debris. Clean up oil or fuel spills. Storage DO NOT store unit inside a building with fuel in the fuel tank where any ignitio...

Page 7 - SECTION 3 - SPECIFICATIONS

3 - 7 SECTION 3 - SPECIFICATIONS Model Number 932025 932026 932027 932029 932030 Description ST 5+2 ST 524 ST 724 ST 824 ST 5+2 Engine HSK-50 HSK-50 HSK-70 HSK-80 HSK-50 Manufacturer Tecumseh Tecumseh Tecumseh Tecumseh Tecumseh Fuel Unleaded Unleaded Unleaded Unleaded Unleaded Fuel Tank Capacity - q...

Page 11 - CONTROLS AND FEATURES; SECTION 4 - GENERAL MAINTENANCE & ADJUSTMENTS

4 - 11 4.1 CONTROLS AND FEATURES SECTION 4 - GENERAL MAINTENANCE & ADJUSTMENTS 1. Traction Drive Lever2. Attachment Clutch Lever3. Engine Ignition and Key4. Primer Bulb5. Choke6. Throttle7. Speed Selector8. Recoil Starter Handle9. Chute Crank10.Discharge Chute Deflector 11.Discharge Chute12.Auge...

Page 12 - SERVICE POSITIONS; Belt Service Position; FILLING THE FUEL TANK

4 - 12 4.2 SERVICE POSITIONS Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine service be required, contact an Ariens dealer or an authorized engine manufacturer’s service center. Belt Service Position To ensure...

Page 13 - GENERAL LUBRICATION

4 - 13 To add fuel to the fuel tank: 1. Refuel the unit only in a well ventilated, open area. 2. Stop the engine and allow to cool. 3. Clean the fuel cap and the area around the fuel cap to prevent dirt from entering the fuel tank. Remove the cap from the fuel tank. 4. Fill the fuel tank to within 1...

Page 15 - ATTACHMENT DRIVE BELT; To Replace the Attachment Drive Belt:; TRACTION DRIVE BELT

4 - 15 4.8 ATTACHMENT DRIVE BELT To Replace the Attachment Drive Belt: 1. Shut off engine and allow to cool completely. 2. Place unit in Belt Service Position. 3. Support handlebar. 4. Loosen lower cap screws holding attachment to frame (one on each side). 5. Remove upper cap screws. 6. Separate hou...

Page 18 - Attachment Clutch/Impeller Brake

4 - 18 Attachment Clutch/Impeller Brake To check impeller brake: 1. Tip unit forward onto auger/impeller housing. 2. Remove bottom cover by removing four cap screws. 3. Measure distance between impeller brake shoe pad and belt with attachment clutch engaged (Figure 10). Impeller brake shoe should be...

Page 20 - ATTACHMENT CLUTCH HANDLE

5 - 20 5.1 LOWER HANDLEBAR Remove nut and washer attaching lower handlebar to each side of frame and remove lower handlebar. Check parts for wear or replacement. Assemble, using reverse procedure. 5.2 ATTACHMENT CLUTCH HANDLE Remove (2) push nuts, pin and (2) screws holding Clutch Handle and pivot t...

Page 21 - ENGINE TROUBLESHOOTING

6 - 21 6.1 ENGINE TROUBLESHOOTING The following troubleshooting chart is to be used to isolate engine problems and give possible causes and corrective action responses. The troubleshooting key is generic and can be used for several types of engines. Use only those possible causes and corrective acti...

Page 23 - SECTION 7 - REDUCTION DRIVE

7 - 23 7.1 WHEELS AND AXLE The wheels are bolted directly to the axle shaft. To remove the wheels, loosen the bolt and nut. Push the bolt out and slide the wheel hub off of the axle. To remove the axle, 1. Place the unit in the Upright Service Position. 2. Remove both wheels. 3. 724 Models- Remove b...

Page 24 - NOTE: On 824 Models install sprocket and bushing.; SECTION 8 - FRICTION WHEEL DRIVE

8 - 24 8.1 FRICTION WHEEL 1. To replace friction wheel, tip unit up onto housing on a level surface. 2. Remove bottom cover by removing four cap screws. 3. Remove right hand wheel, tire. 4. Remove bearing flange screws on the right hand side of the frame. Remove bearing flange on frame (Figures 16 a...

Page 29 - ALUMINUM GEAR CASE; SECTION 10 - GEAR CASE

10 - 29 10.1 ALUMINUM GEAR CASE 1. Remove auger/impeller and gear case from housing referring to Auger/Impeller Section. 2. Remove six bolts that hold right and left gear case halves together (Figure 23). 3. If flange bushings need replacement, first remove seals from outside of gearcase halves with...