Arcam A32 - Manuals - manualsarea.com

Page 3 - Using this handbook; SAFETY; CONTENTS; OTHER LANGUAGES

3 Using this handbook This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam A32 integrated amplifier or the P35 power amplifier. The A32 amplifier is described first, then the P35. The CR-389 remote control handset supplied with the A3...

Page 4 - Safety guidelines; SAFETY INSTRUCTIONS; SAFETY COMPLIANCE

4 Safety guidelines SAFETY INSTRUCTIONS This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions: 1. Take heed of warnings and instructions You should read all the safety and operating ...

Page 5 - Installation: A32 integrated amplifi er; 9 bk bl bm bn bo bp

5 POSITIONING THE UNIT Place your amplifier on a level, firm surface. Avoid placing the unit in direct sunlight or near sources of heat or damp. Ensure adequate ventilation. Do not place the unit in an enclosed space such as a bookcase or cabinet as both of these will impede air flow through the ven...

Page 6 - CONNECTING TO A POWER SUPPLY; MAINS LEAD; STANDBY POWER; CONNECTING TO OTHER EQUIPMENT; PRE/POWER AMPLIFIER CONNECTIONS

6 CONNECTING TO A POWER SUPPLY WRONG PLUG? Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting (115V or 230V) indicated on the rear panel of the unit 2 before plugging in. If your mains supply voltage or mains plug is differe...

Page 7 - Using your A32 integrated amplifi er; FRONT PANEL CONTROLS; bm; bk

7 Using your A32 integrated amplifi er FRONT PANEL CONTROLS This section describes how to operate your amplifier. If your amplifier has not been installed for you, you should first read the section ‘Installation: A32’ on page 5. POWER (and power indicator light) bm Switches the unit on and off. (You...

Page 8 - RECORDING

8 RECORDING With the Arcam A32 it is possible to listen to and record from one source, or to listen to one source while recording another. Both sets of tape sockets are identical in sensitivity and suitable for use with almost any type of recorder (cassette, CDR, MD, VCR, reel-to-reel, etc.). The re...

Page 9 - Setting up your A32 integrated amplifi er; INTRODUCTION

9 Setting up your A32 integrated amplifi er Choose setting Adjust BALANCE Adjust BASS Adjust TREBLE Adjust LEFT RIGHT –dB +dB –dB +dB Customize -> DOWN UP edit STANDARDFINEREFERENCE continue VolumeResolution GRAPHIC/NUMERIC edit GLOBAL/PERSOURCE continue edit ARCAM Amp continue edit AUX/PHONO con...

Page 10 - Using the remote control; CR-389 REMOTE CONTROL

10 Using the remote control NOTE Remember to install the two AAA batteries supplied before tr ying to use your remote control.Do not place anything in front of the FMJ badge on the top left of the CD player (where the IR receiver is located), or the remote control may not work. CR-389 REMOTE CONTROL...

Page 11 - Installation: P35 power amplifi er; REMOTE SWITCHING

11 Installation: P35 power amplifi er CONNECTING TO OTHER EQUIPMENT Follow the installation instructions for the integrated amplifier on pages 4–6. AUDIO IN – Connect this input to the output sockets of your pre- amplifier or the PRE OUT sockets of an integrated amplifier. MONO LINK – The power ampl...

Page 12 - Using your P35 power amplifi er

12 Using your P35 power amplifi er POWER (AND POWER INDICATOR LIGHT) Switches the unit on and off. The light indicates the status of the amplifier. When you switch your amplifier on, the light glows amber for a few seconds, during which time the speakers are disconnected. The light changes to green ...

Page 14 - Technical specifi cations; CONTINUAL IMPROVEMENT POLICY

14 Technical specifi cations NOTE : All specification values are typical unless otherwise stated. CONTINUAL IMPROVEMENT POLICY Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice. A32 P35 Continuous power outpu...

Page 15 - Service information; SOUND CUTS OUT FOR NO REASON; ON LINE REGISTRATION; Guarantee

15 Service information Before returning your amplifier for ser vice, please check the following: SOUND CUTS OUT FOR NO REASON If the temperature of the internal heatsink rises above a safe level, then a thermal cutout inside the amplifier will operate. The power indicator on the front panel flashes ...