AMX AXB-DTMF+ - Manuals

AMX AXB-DTMF+ – Manual in PDF format online.

Manuals:

Manual

Manual AMX AXB-DTMF+

Summary

Page 2 - AMX Limited Warranty and Disclaimer; determination of rights.

AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted fo...

Page 3 - Table of Contents

Table of Contents i AXB-DTMF+ DTMF+ Interface Table of Contents Product Information ................................................................................................. 1 Specifications ........................................................................................................

Page 5 - Product Information; calls to any pager or cellular phone.; Specifications

Product Information 1 AXB-DTMF+ DTMF+ Interface Product Information The AXB-DTMF+ DTMF Interface (FIG. 1) links an Axcess central controller to a telephone network, enabling dual tone multi-frequency (DTMF) and audio pass-through control. The AXB- DTMF+, with a programmed central controller, process...

Page 7 - Configuration and Installation; setting for a leased line or phone operation.; to; Remove the jumper from pins 2 and 3, and place it on pins 1 and 2.

Configuration and Installation 3 AXB-DTMF+ DTMF+ Interface Configuration and Installation Setting the Internal Jumpers There are two 2-position jumpers on the AXB-DTMF+ circuit card (FIG. 1). Each jumper is set to a default pin setting. These jumpers are positioned to enable automatic call answering...

Page 8 - Line Setting mode; Preparing captive wires; Wiring Guidelines at 80 mA

Configuration and Installation 4 AXB-DTMF+ DTMF+ Interface Line Setting mode The 2-position jumper JP1 selects PHONE or LEASED line operation when system powers on. FIG. 3 shows the default setting. To change the line setting default from PHONE to LEASED : 1. Remove the AXB-DTMF+ cover from the unit...

Page 9 - Connecting External Telephone Lines

Configuration and Installation 5 AXB-DTMF+ DTMF+ Interface Connecting External Telephone Lines Telephone cabling for both the input and extension lines are standard RJ-11 type connections. Follow these steps to connect external telephone lines. 1. Check the circuit card jumper settings to match line...

Page 10 - Off-hook line and off-hook phone troubleshooting

Configuration and Installation 6 AXB-DTMF+ DTMF+ Interface Testing the AXB-DTMF+ Follow these steps to test the AXB-DTMF+: 1. Disconnect AXlink power. 2. Remove the cover from the unit housing and set the AUTO ANSWER jumper to AUTO ANSWER ON then reinstall the cover on the unit housing. 3. Reconnect...

Page 11 - Programming; the control; Operative; : commands that define distinctive ring patterns.; Operative System Send_Commands

Programming 7 AXB-DTMF+ DTMF+ Interface Programming Program the AXB-DTMF+ to send outbound DTMF codes using Axcess Send_Commands from the control Fine Tuning - commands allowing experienced users the ability to obtain performance in adverse system. Use the commands described in this section with the...

Page 14 - Timing System Send_Commands

Programming 10 AXB-DTMF+ DTMF+ Interface Timing System Send_Commands The following table lists the commands, which establish normal signal timing. The commands are listed alphabetically by operation and include syntax, syntax descriptions, usage examples, time increments, and reset default values. O...

Page 18 - Fine Tuning Send_Commands

Programming 14 AXB-DTMF+ DTMF+ Interface Fine Tuning Send_Commands The following table lists the commands that fine tune AXB-DTMF+ signal timing. Most likely, you will not have to change Fine Tuning parameters.The commands are listed alphabetically by operation and include syntax, syntax description...

Page 19 - Distinctive Ring Patterns and Send_Commands

Programming 15 AXB-DTMF+ DTMF+ Interface Distinctive Ring Patterns and Send_Commands Distinctive ringing is a service provided by the local telephone company. Distinctive ring allows additional phone numbers to be assigned to a single phone line. Then, depending upon the number dialed, the ringing p...

Page 20 - Changing a Default Ring Pattern

Programming 16 AXB-DTMF+ DTMF+ Interface Changing a Default Ring Pattern Change a default ring pattern using the appropriate Send_Command when programming the AXB- DTMF+. Each ring pattern consists of five parts with each part having a specific Send_Command. For more information on distinctive ring ...

Page 21 - Distinctive Ring Send_Commands

Programming 17 AXB-DTMF+ DTMF+ Interface Distinctive Ring Send_Commands The following Send_Commands are available for changing the default distinctive ring patterns. Each ring pattern consists of five parts with each part requiring a Send_Command. Distinctive ring Send_Commands produce four patterns...

Page 22 - Axcess Program Example

Programming 18 AXB-DTMF+ DTMF+ Interface Axcess Program Example To program the AXB-DTMF+, you will need a personal computer with the Axcess software program, an Axcess Central controller, an AXlink power/data cable, as well as an CC-COM Axcess programming cable. For the program example, complete the...

Page 26 - Channel Codes

Programming 22 AXB-DTMF+ DTMF+ Interface Channel Codes Channel codes on the AXB-DTMF+ are stored in memory (firmware) and process all outbound or inbound DTMF from a set of program instructions downloaded to the Axcess Central controller. Channel Codes Operation Channel # Description (ON Indicates) ...

Page 28 - description and format use are also described.; Caller ID

Programming 24 AXB-DTMF+ DTMF+ Interface Caller ID The AXB-DTMF+ provides report capability for receiving Caller ID information. The following table shows the Caller ID data string sent to the Axcess AXC-EM Enhanced Master Card. A description and format use are also described. Program Example for Ca...