Amana W10216187A - Manuals

6 Closet installation - Dryer only A B 14" max.*( 3 56 mm) 18" min.*(457.2 mm) 48 in. 2* ( 3 100 mm 2 ) 24 in. 2* (1550 mm 2 ) 5"**(127 mm) 1"*(25 mm) 3 1½" (800 mm) 3 "* (76 mm) 3 "* (76 mm) A. Side view - closet or confined areaB. Closet door with vents * Required spaci...

7 Electrical Requirements Electrical S hock Hazard Plu g into a g rounded 3 pron g outlet. Do not remove g round pron g . Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. WARNING ■ 120 Volt, 60 Hz., AC only, 15-...

8 ■ If your dryer has been converted to use LP gas, 3 / 8 " LP compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe. NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON ®† tape. ■ Must inc...

9 If this is a new vent system Vent material ■ Use a heavy metal vent. Do not use plastic or metal foil vent. ■ 4" (102 mm) heavy metal exhaust vent and clamps must be used. DURASAFE™ venting products are recommended. 4" (102 mm) heavy metal exhaust vent 4" 102 mm DURASAFE™ vent products...

11 Install Vent System 1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood. 2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. 3. Run vent to dryer location. Use the straightest path...

12 A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size, and location. A. 3 / 8 " flexible gas connector B. 3 / 8 " dryer pipe C. 3 / 8 " to ...

13 3. Move the large hole screw to the opposite side. Remove the 2 plug screws and plastic plugs, and insert them in the original screw holes on the opposite side. A. Hinge screwsB. Large hole screw C. Plug screws and plastic plugs A C B 4. Move hinge to the other side and reattach with the 4 screws...

14 4. Check that the dryer is level. See “Level Dryer.” Electrical S hock Hazard Plu g into a g rounded 3 pron g outlet. Do not remove g round pron g . Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. WARNING 5....

17 Delicate Use this cycle to get extra-low heat to gently dry items such as lingerie, blouses, or washable knit fabrics. Automatic Dry Preset Cycle Settings Automatic Cycles Loa d Type Temperature Time* (Minutes) HEAVY DUTY Heavyweight mixed loads, cotton towels, bedspreads High 45 DENIM Denim jean...

18 ■ Stop Wrinkle Prevent at any time by pressing WRINKLE PREVENT or opening the dryer door. ■ For the Casual cycle, Wrinkle Prevent is preset to ON. The other cycles will retain the Wrinkle Prevent setting. For example, if you select Wrinkle Prevent in the Normal cycle, Wrinkle Prevent will be on t...

19 End of Cycle Signal En d of Cycle Signal The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling. Press CYCLE SIGNAL to adjust the sound level or turn off the signal. NOTE: When Wrinkle Prevent is sel...

20 DRYER CARE Cleaning the Dryer Location Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air. Cleaning the Lint Screen Every loa d cleaning The lint screen is located in the door opening of the dryer. The control panel has an indicator light to r...

21 Moving care 1. Unplug the power supply cord. 2. Close shutoff valve in gas supply line. 3. Disconnect gas supply line pipe and remove fittings attached to dryer pipe. 4. Cap the open fuel supply line. 5. Make sure leveling legs are secure in dryer base. 6. Use masking tape to secure dryer door Ch...

22 Dryer Results Clothes are not d rying satisfactorily, d rying times are too long, or loa d is too hot ■ Is the lint screen clogge d with lint? Lint screen should be cleaned before each load. WARNIN G Fire Hazar d Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Fai...

23 ASSISTANCE OR SERVICE Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance...