Amana REMOTE HEAT PUMP- Manuals

5 TRANSPORTATION DAMAGE All units are securely packed in shipping containers tested according to International Safe Transit Association specifications. The carton must be checked upon arrival for external damage. If damage is found, a written request for inspection by the carrier’s agent must be mad...

6 Installation Instructions To ensure that the unit operates safely and efficiently, it must be installed, operated and maintained according to these installation and operating instructions and all local codes and ordinances or, in their absence, with the latest edition of the National Electric Code...

7 Installation Instructions SLEEVE INSTALLATION In order for condensate water to drain properly inside the unit, the sleeve must be installed properly: • Level from right to left. • A slight downward pitch from the indoor side to the outdoor side as shown below. Refer to the Installation Instruction...

8 Chassis Wall Sleeve Outside Wall Screws (3 on each side of unit) Chassis Installation View 2 Installation Instructions Wiring WARNING T O AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK, DO NOT SERVICE THIS UNIT WITHOUT FIRST SHUTTING OFF POWER TO THE UNIT FROM THE CIRCUIT ...

9 Operating Instructions 230/208 Volt Units 265 Volt Units Heater Size (kW ) Power Cord Rating (amp) Power Cord Rating (amp) 1.5 15 20 2.5 15 20 3.5 20 Not Applicable 3.7 Not Applicable 20 5.0 30 30 Power Cord Requirements Table 1 - Power Cord Requirements NOTE : Heaterless units are shipped with an...

10 ON / OFF MASTER SWITCH P11 M2 M1 SW2 P10 COM A COM B P12 P13 IAT BLACK DS 1 D S2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH REM OTE THERMOS TAT AUXILIARY Control Board User Inputs* *NOTE: The PTAC Wire Harness Kit (PWHK01C) is required for the auxiliary or remote thermostat options. ADD...

11 No holes are permitted in chassis basepan or wallsleeve when routing low voltage wire. Route the low voltage wires through the indention on the front of the basepan. Low Voltage Wires Routing VENT CONTROL The vent control allows outside air to be drawn into the condi- tioned area. This outside ai...

12 3. Remove the four (4) nuts which secure the discharge air grilleto the cabinet front. Discharge Air Flow Grille Removal 4. Rotate the grille 180° clockwise. 5. Reinstall the nuts securing the discharge air grille to the cabi-net front. Reinstall the cabinet front on the unit. REMOTE THERMOSTAT T...

13 3. Run 6 to 8 wires during initial installation. Tape or cap off anyunused wires. DS1 DS2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH REMOTE THERMOSTAT AUXILIARY X1 O B** Y W1 W2 G* R Thermostat Connections Control Board Connections Wiring Schematic for Straight Cool Unit *NOTE: For high...

14 WARNING T O AVOID THE RISK OF PROPERTY DAMAGE, ELECTRICAL SHOCK OR PERSONAL INJURY, CLEAN AIR FILTERS AND COILS REGULARLY. C LOGGED OR SEVERLY RESTRICTED FILTERS OR COILS REDUCE AIRFLOW WHICH CAN CAUSE DRASTIC EFFICIENCY LOSS AS WELL AS SEVERE COMPONENT DAMAGE TO COMPRESSORS, ELECTRIC HEATER OR F...

15 Cabinet Front The cabinet front and discharge air grille can be cleaned with a water dampened cloth . Under no circumstances should hydro- carbon-based cleaners (e.g. acetone, benzene, naphtha gaso- line, etc.) be used to clean the front or air grilles. Use care when cleaning the control area . Y...

16 Normal Operating Sounds and Conditions Water trickling sounds Water is picked up and distributed over the coil. This improves the efficiency andhelps with water removal. Water dripping Water will collect in the base pan during high humidity days. This can causeoverflow and drip from the outside o...

18 The Diagnostic Maintenance & Status Report provides detailed information on PTAC control operation and operational status includ-ing present modes, failures, airflow restriction warnings, operating temperatures, and past failures. The lower right hand dot on thecenter display flashes in this ...

19 STATUS DISPLAY ERROR LIGHT SUGGESTED ACTION FP Fre e ze Prote ction Engaged. The room temperature measured by the wireless remote thermostat or indoor ambient thermistor active sensor falls below 40°F. Y N No Action required. This setting will disengage when the room temperature rises above 43°F....