Page 2 - Installation Requirements; To reduce risk of fire, use only metal duct.
2 Important Safety Instructions Recognize this symbol as a SAFETY message Installation Requirements Caution To avoid personal injury, mountingsurface must be capable of supportingmicrowave oven (65 lbs.) and oven loads(up to 50 lbs.) for a total weight of 115 lbs. Caution To avoid personal injury, d...
Page 3 - Hood Exhaust Duct; Description
3 Materials Needed (Not Supplied) • Phillips screwdriver • Pencil • Ruler or tape measure and straight edge • Protective gloves • Carpenter square (optional) • Tin snips (in some applications) • Electric drill with 1 / 2 , 3 / 16 , and 5 / 8 inch drill bits • Hammer • Stud finder (optional) • Filler...
Page 4 - Installation Instructions; Lift off blower plate.; B. Preparing Microwave Exhaust Duct; NOTE: Microwave oven is shipped assembled for top; Removing Mounting Plate
4 Installation Instructions Outside Back Exhaust (Horizontal Duct) 1. Slide exhaust adaptor to one side, squeeze sides andremove. Save damper and exhaust adaptor. Seediagram above. 2. Remove and save 3 screws holding blower plate tomicrowave oven. 3. Lift off blower plate. Outside Top Exhaust (Verti...
Page 5 - Caution
5 7. Guide wires into duct while placing blower unit backinto opening. Secure blower motor with screwremoved in step 4. 9. Fit exhaust adaptor into house duct. Be sure damperhinge is on top and damper swings free into walloutlet. 10. Remove paper from sticky side of 28 inch foam tape strip. Press st...
Page 6 - Remove 2 screws on front of grille. Remove grille.; C. Preparing Top Cabinet; Read instructions on top cabinet template.; D. Mounting Bracket Assembly to Wall; Replace blower plate using 5 screws.
6 5. Carefully pull out blower unit. Wires extend farenough to allow blower adjustments. 6. Roll blower unit so blades face towards front ofmicrowave oven. Wires should be routed in front ofmotor frame. 7. Guide wires into duct while placing blower unit backinto opening. Secure blower motor with scr...
Page 7 - E. Preparing Rear Wall Cutout Opening for; Note: After locating stud or studs, stud center can be
7 6. Draw third circle through one of top or bottomholes to match location of stud. NOTE: For outside back exhaust, microwave oven requires rear wall cutout opening for rear wallduct. See "Preparing Rear Wall Cutout Openingfor Outside Back Exhaust" section. 3. Verify exhaust adaptor (with da...
Page 2 - Installation Requirements; To reduce risk of fire, use only metal duct.
2 Important Safety Instructions Recognize this symbol as a SAFETY message Installation Requirements Caution To avoid personal injury, mountingsurface must be capable of supportingmicrowave oven (65 lbs.) and oven loads(up to 50 lbs.) for a total weight of 115 lbs. Caution To avoid personal injury, d...
Page 3 - Hood Exhaust Duct; Description
3 Materials Needed (Not Supplied) • Phillips screwdriver • Pencil • Ruler or tape measure and straight edge • Protective gloves • Carpenter square (optional) • Tin snips (in some applications) • Electric drill with 1 / 2 , 3 / 16 , and 5 / 8 inch drill bits • Hammer • Stud finder (optional) • Filler...
Page 4 - Installation Instructions; Lift off blower plate.; B. Preparing Microwave Exhaust Duct; NOTE: Microwave oven is shipped assembled for top; Removing Mounting Plate
4 Installation Instructions Outside Back Exhaust (Horizontal Duct) 1. Slide exhaust adaptor to one side, squeeze sides andremove. Save damper and exhaust adaptor. Seediagram above. 2. Remove and save 3 screws holding blower plate tomicrowave oven. 3. Lift off blower plate. Outside Top Exhaust (Verti...
Page 5 - Caution
5 7. Guide wires into duct while placing blower unit backinto opening. Secure blower motor with screwremoved in step 4. 9. Fit exhaust adaptor into house duct. Be sure damperhinge is on top and damper swings free into walloutlet. 10. Remove paper from sticky side of 28 inch foam tape strip. Press st...
Page 6 - Remove 2 screws on front of grille. Remove grille.; C. Preparing Top Cabinet; Read instructions on top cabinet template.; D. Mounting Bracket Assembly to Wall; Replace blower plate using 5 screws.
6 5. Carefully pull out blower unit. Wires extend farenough to allow blower adjustments. 6. Roll blower unit so blades face towards front ofmicrowave oven. Wires should be routed in front ofmotor frame. 7. Guide wires into duct while placing blower unit backinto opening. Secure blower motor with scr...
Page 7 - E. Preparing Rear Wall Cutout Opening for; Note: After locating stud or studs, stud center can be
7 6. Draw third circle through one of top or bottomholes to match location of stud. NOTE: For outside back exhaust, microwave oven requires rear wall cutout opening for rear wallduct. See "Preparing Rear Wall Cutout Openingfor Outside Back Exhaust" section. 3. Verify exhaust adaptor (with da...