Page 2 - Unpacking; WARNING
2 OWNER'S PRODUCT IDENTIFICATION MODEL NUMBER SERIAL NUMBER MANUFACTURING NUMBER Owner's Name Address City State Zip / / Date of Purchase Authorized Dealer Address City State Zip ( ) Phone Number To avoid death, personal injury or propertydamage due to electrical shock: • Observe all local codes and...
Page 3 - Electrical Requirements; Grounding Instructions; Installation; Unit with a window mounting kit; Room Heat Pumps; CAUTION
3 NEMA No. 5-15P NEMA No. 5-15R 125V-15AMP 115V NEMA No. 6-15P NEMA No. 6-15R 250V-15AMP 230/208V ratedat 12 amperes orless NEMA No. 6-20P NEMA No. 6-20R 250V-20AMP 230/208V ratedover 12 amperes,but not more than16 amperes NEMA No. 6-30P NEMA No. 6-30R 250V-30AMP 208V rated over16 amperes, butnot mo...
Page 4 - by Control Released; Figure H
4 Annual Inspection It is suggested that your unit be inspected by your dealer orservicer once a year. It is advisable to have the outer caseremoved and the unit thoroughly cleaned. Note: The life of your unit may be greatly reduced if you livein a salt air or other corrosive type environment. Under...
Page 5 - Air Conditioner; BEFORE YOU BEGIN; ELECTRICAL REQUIREMENTS
5 InstallationInstructions Air Conditioner BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. • IMPORTANT - Observe all governing codes and ordinances. • Note to Installer - Be sure to leave these instructions with the ...
Page 6 - PARTS INCLUDED; Installation Instructions
6 Type A (6) V-support (2) Win do w lo c kin g br a c ke t (2) Top mounting rail Rig h t accordion panel Foam top window gasket Win do w sash seal Left accordion pa n e l Type B (4) Type C (7) Type E (6) Bolt (2) & nuts (2) PARTS INCLUDED ( A ppe a r a n c e m a y v a r y ) Installation Instruct...
Page 7 - WINDOW REQUIREMENTS; STORM WINDOW REQUIREMENTS
7 17 3/8" min. 30 to 41" min. (With accordion panels) 26" min. (Without accordion panels) 1/2" higherthan frame Stormwindowframe Wood Stool • These instructions are for a standard double-hung window. You will need to modify them forother types of windows. • The air conditioner can be...
Page 8 - PREPARE THE CASE; I n s t a l l a t i o n I n s t r u c t i o n s
8 PREPARE THE CASE Ins tall the top m ounting rail w ith 4 ty pe Bs crew s from the ins ide of the cas e. Insert the frames for the accordion panelsinto the top mounting rail and the bottomframe guides. Attach the accordion panels to the side of the case using 3 type A screwson each s ide. N ote: Wh...
Page 9 - I n s t a l l a t i o n I n s t r u c t i o n s
9 I n s t a l l a t i o n I n s t r u c t i o n s INSTALL THE CASEIN THE WINDOW (cont.) A djus t the leveling bolts and nuts agains t theouts ide w all s o that the cas e has a s light tiltto the outs ide. T ighten nuts w ith an adjus table wrench. Use a level; about a 1/2 bubble willbe the correct ...
Page 10 - INS TALL THE AIR CONDITIONER; IN THE CASE; INSTALL THE AIR CONDITIONER; Reins tall the filter.
10 INS TALL THE AIR CONDITIONER IN THE CASE Slide the airconditioner into the cas e. Do notpus h on thecontrols or thefinned coils . Make s ure the air conditioner is firm ly s eated. Reins tall the locking bracket and s crewrem oved earlier . Reconnect the ground w ire to the airconditioner us ing ...
Page 11 - General Operating Instructions; Operating Controls; See page 12 under; only
11 General Operating Instructions While operation of all units is similar, controls vary slightlyfrom model to model. Operating Controls section shows control panel of unit purchased and gives detailed informationabout operation of controls. Initial Start-Up and Cooling Select the highest fan speed ...
Page 12 - COMFORT ZONE; AND HEAT PUMP MODELS; CIRCULAIRE
12 Fan Control OFF – Completely shuts off the unit. To prevent blowingfuses, wait three minutes after turning the unit off beforeturning it on again. LOW COOL – Filters and circulates room air with the fanrunning continuously on low speed. Also cools and dehu-midifies while the compressor is running...
Page 13 - Before Calling Service; If the problem cannot be fixed using the suggested remedies, see
13 Before Calling Service PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY UNIT W ILL NOT RUN No power to unit Push reset button on power cord. Set Fan Control to position other than OFF. Make sure plug is firm ly seated in outlet. Check for blown fuses, tripped circuit breakers. LITTLE OR NO COOLING LITTLE ...
Page 14 - When Service Is Required; An accurate description of problem.
14 When Service Is Required Your room air conditioner dealer can give you the name ofyour nearest Authorized Service Center. Help them giveyou prompt service by providing: • An accurate description of problem. • Complete model, serial, and manufacturing numbersfrom serial plate. • Proof of purchase ...
Page 15 - Outer Case Dimensions; General Instructions; All Amana; Introduction; Air Conditioner Dimensions; Thru-wall Installation Instructions; for Amana
15 26" Dimension of Bottom Rail " 4” Front ofouter case Bottom rail Outer Case Dimensions (chassis removed) General Instructions All Amana ® brand Compact Room Air Conditioners feature a slide-out chassis. Chassis and front cover must be re-moved from outer case for installation. Introductio...
Page 16 - Brick Veneer or Frame Wall Construction; Framing; Framed/Finished Opening; Placement of Outer Case in Opening; Dimensions of Finished Opening; Masonry Construction; See CAUTION under General Instructions.
16 In order to reinstall the chassis and re-attach the air conditioner front cover, theinstalled outercase must be square and level from side to side. Use wood shimsbetween sides of case and finished open-ing - especially where case is secured toopening - to prevent warping or distorting.Check insta...
Page 17 - Installed Case; (brick veneer or frame wall construction shown)
17 When case is properly positioned in opening, use woodshims to fill any gaps between case and finished opening,especially in area where case will be secured to opening. Take care not to warp or distort case when installingshims . For condensate drainage, install drainage cup in drain hole on basep...