Amana GUSA- Manuals

Page 2 - PRODUCT IDENTIFICATION; WARNING; B: Initial Design Series; CAUTION

PRODUCT IDENTIFICATION 2 Rev. 2 The model and manufacturing number are used for positive identification of component parts used in manufacturing.When engineering and manufacturing changes take place where interchangeability of components are affected, themanufacturing number will change. It is very ...

Page 3 - PRODUCT DIMENSIONS; Cabinet

PRODUCT DIMENSIONS 3 Rev. 2 GUSA___BX__ (Manufacturing Numbers P1239502-06F and P1242002-06F) GUSA___BX__ Cabinet Size Units A B C D 090__50115__50 070__35 090__40 All dimensions are in inches. Small Medium Large 15 19 23 16-1/2 20-1/2 24-1/2 12-5/8 14-5/8 18-5/8 12-3/8 16-3/8 20-3/8 AIR DISCHARGE A...

Page 5 - COMPONENT IDENTIFICATION; Integrated Control Module

5 Rev. 2 COMPONENT IDENTIFICATION GUSA___BX__ (Manufacturing Numbers P1239502-06F and P1242002-06F) Integrated Control Module 17 Two-Speed Induced Draft Blower 18 Electrical Connection Inlet (Alternate) 19 Coil Front Cover Pressure Tap 20 Coil Front Cover Drain Tap 21 Drain Line Penetrations 22 Drai...

Page 7 - PRODUCT DESIGN; High Altitude Derate; General Operation

7 Rev. 2 PRODUCT DESIGN 3. Conversion kits for high altitude natural or propane gas operation are available. See High Altitude Derate chartfor details. 4. Installer must supply the following gas line fittings, de- pending on which entrance is used: Left -- Two 90º Elbows, one close nipple, straight ...

Page 10 - Permanent Minimum Filter Area (in; Filters can also be installed elsewhere; Thermostats

10 Rev. 2 PRODUCT DESIGN Thermostats: The following Amana Thermostats are suggested for use with the GUSA Furnace Models: Filters: Filters are required with this furnace and must be provided by the installer. The filters used must comply with UL900 orCAN/ULCS111 standards. Installing this furnace wi...

Page 11 - FURNACE SPECIFICATIONS

1. These furnaces are manufactured for natural gas operation. Optional kits are available for conversion to propane operation. 2. For elevations above 2000 feet the rating should be reduced by 4% for each 1000 feet above sea level. The furnace must not be derated, orifice changes should only be made...

Page 12 - BLOWER PERFORMANCE SPECIFICATIONS; For most jobs, about 400 CFM per ton when cooling is desirable.

BLOWER PERFORMANCE SPECIFICATIONS 12 Rev. 2 1. Blower speeds for each firing rate are set independently of each other. 2. CFM in chart is without filters(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return filters, this chart assumes b...

Page 13 - MP; CF; U O

13 Rev. 2 BLOWER PERFORMANCE SPECIFICATIONS 3 0 40 50 60 70 80 9 0 11 0 1 2 0 10 0 130 1 4 0 1 5 0 10 0 90 80 70 60 50 40 30 20 10 OUT P UT BTU/ H R x 10 00 B T U OUT P UT v s T E M P E R ATUR E RI SE CHA RT TE MP ER AT URE RI SE 60 0 CF M 700 90 0 100 0 110 0 120 0 1400 160 0 18 0 0 20 0 0 22 0 0 2...

Page 14 - WIRING DIAGRAMS

14 Rev. 2 TO AVOI D P O SSI B L E E L ECTRI CAL SHOCK, PERSONAL I N J URY, OR DEATH, DI SCON NE CT THE POW E R B E FORE SERVI CI NG. WARNING ! WIRING DIAGRAMS GUSA___BX__ (Manufacturing Numbers P1239502-06F and P1242002-06F) WA RNING:DISCONNE CT POW ER BEFORE S ERVICING.WIRING TO UNIT MUS T BEP ROPE...

Page 16 - SCHEMATICS; TYPICAL SCHEMATIC

16 Rev. 2 SCHEMATICS TO AVOI D P O SSI B L E ELECTRI CAL SHOCK , PERSONAL I N JURY, OR DEATH, DI SCON NECT THE POW E R B E FORE SERVI CI NG. WARNING ! TYPICAL SCHEMATIC GUSA___BX__ MODEL FURNACES WR 50M61-288 INTEGRATED IGNITION CONTROL This schematic is for reference only. Not all wiring is as show...