Amana AGR6303MMB - Manuals

7 Location Requirements IMPORTANT: Observe all governing codes and ordinances. � It is the installer’s responsibility to comply with installationclearances specified on the model/serial/rating plate. Themodel/serial/rating plate is located on the frame behind a topcorner of the door or either side o...

8 Electrical Requirements – U.S.A.Only If codes permit and a separate ground wire is used, it isrecommended that a qualified electrical installer determine thatthe ground path and wire gauge are in accordance with localcodes. Do not use an extension cord. Be sure that the electrical connection and w...

9 INSTALLATION Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install or uninstallappliance. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do no...

12 � Tighten strain relief screw against the power supply cord. Style 2: Direct wire strain relief � Remove the knockout as needed for the flexible conduitconnection. � Assemble a UL listed conduit connector in the opening. A. Removable retaining nutB. Conduit � Tighten strain relief screw against t...

13 5. Use 3/8" (9.5 mm) nut driver to connect the neutral (white)wire to the center terminal block post with one of the 10-32hex nuts. A. 10-32 hex nutB. Ground-link screwC. Line 2 (red) D. Green ground wireE. Neutral (center) wireF. Line 1 (black) 6. Connect line 2 (red) and line 1 (black) wire...

16 Level Range Determine if you have AquaLift ® Technology or Steam Clean by referring to the “Range Maintenance and Care” section. For Ranges with AquaLift ® Technology or Steam Clean: 1. Place level on the oven bottom as indicated in one of the twofigures below depending on the size of the level. ...

17 Storage Drawer (on some models) The storage drawer can be removed. Before removing, make suredrawer is cool and empty. To Remove: 1. Pull the storage drawer straight back to the drawer stop. A. Drawer stop notch 2. Lift up the front of the drawer and pull the drawer out. To Replace: 1. Lift up th...

5 Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.If the cabinet depth is greater than 24" (61.0 cm), oven frame must extend beyond cabinet fronts by 1/2" (1.3 cm) min...

6 Gas Supply Requirements Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CG...

7 Burner Input Requirements Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada). Gas Supply Pressure Testi...

8 3. Determine and mark centerline of the cutout space. The mounting can be installed on either the left side or right side of the cutout. Position mounting bracket against the wall in the cutout so that the V-notch of the bracket is 9 5 ⁄ 8 " (24.6 cm) from centerline as shown. A. 9 5 ⁄ 8 "...

9 Complete Connection 1. Locate gas pressure regulator in the back of the range. A. Gas pressure regulator IMPORTANT: Do not remove the gas pressure regulator. 2. Check that the gas pressure regulator shut-off valve is in the “ON” position. A. “ON” positionB. “OFF” position IMPORTANT: The factory de...

10 IMPORTANT: If the back of the range is more than 2" (5.1 cm) from the mounting wall, the rear range foot may not engage the bracket. Slide the range forward and determine if there is an obstruction between the range and the mounting wall. Changes to the gas supply must be performed by a quali...

11 Check Operation of Oven/Broil Burner Electronic oven control (on some models): 1. Open broiler door. 2. Press the “BAKE” pad. n The “BAKE” indicator will light. n “350” will appear in the display. 3. Press the START/ENTER pad. n The “TEMP” and “ON” indicators will appear. n The display will show ...

12 GAS CONVERSIONS Gas conversions from Natural gas to Propane gas or from Propane gas to Natural gas must be done by a qualified installer. Propane Gas Conversion 1. Turn manual shut-off valve to the “closed” position. A. Gas supply lineB. Manual shut-off valve “closed” positionC. To range 2. Unplu...

14 3. Locate Propane gas orifice spud stamped “58” in the bag containing literature supplied with the range. 4. Use a 3/8" (1 cm) combination wrench to remove the Natural gas orifice spud. 5. Install the number “58” Propane gas spud. A. Propane oven orifice spud stamped with “58” IMPORTANT: Do n...

15 2. Remove the cap from the gas pressure regulator using a flat-blade screwdriver. NOTE: Make sure sealing washer remains in the same position. A. Cap 3. To convert to Natural gas, unscrew the plastic adjustment screw by hand, turn it over, and screw it in again. A. CapB. Sealing washerC. Adjustme...

To Convert Oven Burner 1. Open the oven door and remove oven racks and oven tray with flame spreader, and set aside. 2. Remove screw from the oven burner. Lift oven burner and pull the burner toward you. The orifice spud is behind the oven burner air shutter. A. Oven burnerB. Air shutterC. Screw 3. ...