Amana AGR5630BDS2 - Manuals

5 Electrical Requirements IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1. This range is equipped with an electronic ignition sys...

6 Flexible metal appliance connector: ■ If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line. ■ A ½" (1.3 cm) male pipe thread is ne...

7 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer. See the “Storage Drawer” ...

8 Floor Mounting Wall Mounting 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1 ⁵⁄₈ " screws provided. 6. Move range close enough to opening to allow for final gas and electrical connections. Remove shipping base, cardboard or hardboard from und...

9 3. Use a ¹⁵⁄₁₆ " combination wrench and adjustable wrench to attach the flexible connector to the adapters. Check that connector is not kinked. Complete Connection 1. Check that the gas pressure regulator shutoff valve is in the “on” position. 2. Open the manual shutoff valve in the gas supply...

10 IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held ...

11 If the “low” flame needs to be adjusted: 1. Light 1 burner and turn to lowest setting. 2. Remove the control knob. Hold the knob stem with a pair of pliers. Use a small flat-blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size. 3. R...

12 If flame needs to be adjusted:1. Loosen the lock screw on the air shutter located at the rear of the broil burner. 2. Adjust the air shutter as needed. 3. Tighten lock screw. 4. Press CANCEL/OFF when finished. Warming Drawer or Premium Storage Drawer (on some models) Remove all items from inside ...

13 To Replace: 1. Lift up the front of the drawer and place the rear of the drawer inside the range so that the drawer stop notch is behind the drawer glide. 2. Lower the drawer so that the edge of the slide rail drops into the slot in the drawer glide. 3. Slowly push the drawer into the range. NOTE...

14 GAS CONVERSIONS Gas conversions from Natural gas to LP gas or from LP gas to Natural gas must be done by a qualified installer. LP Gas Conversion 1. Turn the manual shutoff valve to the closed position. 2. Unplug range or disconnect power. To Convert Gas Pressure Regulator (Natural Gas to LP Gas)...

15 3. Remove plastic cover from gas pressure regulator cap. 4. Turn gas pressure regulator cap counterclockwise with a ⁵⁄₈ " combination wrench to remove. NOTE: Do not remove the spring beneath the cap. 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the hollow end...

16 4. Remove 2 screws from the front tabs of the flame spreader. Lift front of the flame spreader and pull forward to remove tabs from rear of oven and set it aside on a covered surface. 5. Remove 2 screws from the bake burner. 6. Slide the front of the bake burner to the side to remove tab from fro...

17 Complete Installation (Natural Gas to LP Gas) 1. Refer to the “Make Gas Connection” section for properly connecting the range to the gas supply. 2. Refer to the “Electronic Ignition System” section for proper burner ignition, operation and burner flame adjustments. IMPORTANT: You may have to adju...

18 3. Apply masking tape to the end of a ⁹⁄₃₂ " (7 mm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. 4. Gas orifice spuds are...