Page 2 - RANGE SAFETY; You; DANGER
2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what canhappen if the instructions are n...
Page 3 - WARNING
3 In the State of Massachusetts, the following installation instructions apply: ■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. ■ If using a ball valve, it shall be a T-handle type. ■ A fl...
Page 4 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools needed; Location Requirements; Mobile Home - Additional Installation Requirements; Mobile home installations require:
4 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Parts supplied Check that all parts are included. ■ Literature bag ■ Conversion orifice spuds (inside bag c...
Page 6 - Type of Gas
6 Electrical Requirements IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition. If codes permit and a separate ground wire is used, it is recommended that a ...
Page 7 - Gas Pressure Regulator
7 Flexible metal appliance connector: ■ If local codes permit, a new CSA design-certified, 4-5 ft (122-152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line. ■ A ½" (1.3 cm) male pipe thread is needed f...
Page 8 - INSTALLATION INSTRUCTIONS; Unpack Range; Floor Mounting; Excessive Weight Hazard; Tip Over Hazard
8 INSTALLATION INSTRUCTIONS Unpack Range 1. Do not use oven door handle to lift or move the range 2. Remove shipping materials, tape and film from range. Keep cardboard bottom under range. 3. Remove oven racks and parts package from inside oven. 4. To place range on its back, take 4 cardboard corner...
Page 9 - Make Gas Connection; Typical rigid pipe connection; Explosion Hazard
9 Make Gas Connection Typical rigid pipe connection A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location. 1. Apply pipe-joint compound made for use with LP gas to all pipe th...
Page 10 - Initial lighting and gas flame adjustments; Electrical Shock Hazard
10 5. Close the broiler door. 6. Remove cooktop burner caps and grates from parts package. Align notches in burner caps with pins in burner base. Burner caps should be level when properly positioned. If burner caps are not properly positioned, surface burners will not light. Place burners, burner ca...
Page 11 - Check Operation of Cooktop Burners; If the low flame needs adjusting:; Check Operation of Oven/Broil Burner; If the flame needs adjusting:
11 Check Operation of Cooktop Burners 1. If control panel and knobs were removed earlier, reinstall knobs. 2. Push in and turn each surface unit control knob to the “LITE” position. The flame should light within 4 seconds. 3. Turn control knob to the “HI” position after burner lights. 4. Check each ...
Page 12 - Complete Installation; If range does not operate, check the following:; If you need Assistance or Service:; GAS CONVERSIONS; LP Gas Conversion; To Convert Gas Pressure Regulator
12 7. Tighten the shutter screw. 8. Reinstall flame spreader and oven tray. Reinstall the oven racks. 9. Close the oven door. 10. Close the broiler door. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skippe...
Page 13 - To Convert Surface Burners
13 3. Open broiler door and remove broiler pan. The gas pressure regulator is located in the back right hand corner of the broiler compartment. IMPORTANT: Do not remove the gas pressure regulator. 4. Remove the cap from the gas pressure regulator using a flat-blade screwdriver. NOTE: Do not remove t...
Page 14 - To Convert Oven Burner; Complete Conversion
14 To Convert Oven Burner 1. Open the oven door and remove oven racks, oven tray and flame spreader and set aside. 2. Lift oven burner. The orifice spud is behind the oven burner air shutter. 3. Locate LP gas orifice spud stamped “58” in the package containing literature supplied with the range. 4. ...