Page 2 - RANGE SAFETY; Your safety and the safety of others are very important.; DANGER; WARNING
2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what canhappen if the instructions are n...
Page 3 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools needed; Location Requirements; IMPORTANT: Observe all governing codes and ordinances.; Mobile Home - Additional Installation Requirements; Mobile home installations require:
3 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Parts supplied Check that all parts are included. ■ 3 - 10-32 hex nuts (attached to terminal block) ■ 3 - T...
Page 4 - Product Dimensions; Cabinet Dimensions
4 Product Dimensions IMPORTANT: Range must be level after installation. Follow the instructions in the “Level Range” section. Using the cooktop as a reference for leveling the range is not recommended. * Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs. ** Front of do...
Page 5 - Electrical Connection; Amps
5 Electrical Requirements - U.S.A. Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord. Be sure that the electrical connection a...
Page 6 - INSTALLATION INSTRUCTIONS; Unpack Range; Remove oven racks and parts package from inside oven.; Install Anti-Tip Bracket; Remove the anti-tip bracket from where it is taped inside the; Determine and mark centerline of the cutout space. The; Excessive Weight Hazard; Tip Over Hazard
6 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer. See the “Storage Drawer” ...
Page 8 - Style 1: Power supply cord strain relief; Power Supply Cord
8 Electrical Connection - U.S.A. Only 1. Disconnect power. 2. Remove the terminal block cover screws located on the back of the range. Pull cover down and toward you to remove cover from range. 3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. 4. Add stra...
Page 10 - Direct Wire Installation: Copper or Aluminum Wire; Allow enough slack in the wire to easily attach the wiring
10 4. Use a Phillips screwdriver to connect the green ground wire from the power supply cord to the range with the ground-link screw and ground-link section. The ground wire must be attached first. 5. Use ³⁄₈ " nut driver to connect the neutral (white) wire to the center terminal block post with...
Page 11 - Bare Wire Torque Specifications
11 1. Part of metal ground strap must be cut out and removed. 2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground link under the screw. 3. Pull the wires through the strain relief on bottom of range. Allow eno...
Page 12 - Verify Anti-Tip Bracket Is Installed and
12 2. Attach terminal lugs to line 2 (red), bare (green) ground, and line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque ...
Page 15 - Moving the Range; Check that the anti-tip bracket is installed and engaged. See; Electrical Shock Hazard
15 Moving the Range When moving range, slide range onto cardboard or hardboard to avoid damaging the floor covering. If removing the range is necessary for cleaning or maintenance: For power supply cord-connected ranges: 1. Slide range forward. 2. Unplug the power supply cord. 3. Complete cleaning o...