Altinex PE1005 - Manuals

Altinex PE1005 – Manual in PDF format online.

Manuals:

Manual

Manual Altinex PE1005

Summary

Page 2 - SPECIAL APPLICATION; TABLE OF CONTENTS

SPECIAL APPLICATION 400-0384-003 1 TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS ................ 2 GENERAL .......................................................... 2 INSTALLATION.................................................. 2 CLEANING......................................................

Page 3 - PRECAUTIONS / SAFETY WARNINGS

SPECIAL APPLICATION 400-0384-003 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your PE1005 . Keep this manual handy for future reference. These safety instructions are to ensure the long life of your PE1005 and to prevent fire and shock hazards. Please read them ca...

Page 4 - PIONEER CONTROL CARD; Real Time Clock/Alarms; TECHNICAL SPECIFICATIONS; Compatibility; General; MECHANICAL; Mechanical; ELECTRICAL; Electrical

SPECIAL APPLICATION 400-0384-003 3 ABOUT YOUR PE1005 2 PE1005 PIONEER CONTROL CARD The PE1005 Pioneer Control card allows users to control events on Pioneer Plasma displays using many different control protocols and programmed functions. Key features include: > USB control > RS-232 > RS-485...

Page 5 - APPLICATION DIAGRAMS; DIAGRAM 1: TYPICAL SETUP; CONNECTOR

SPECIAL APPLICATION 400-0384-003 4 DESCRIPTION OF PE1005 4 APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP CONNECTOR RJ-45 NETWORK JACK CONNECTOR TCP/IP DIGITAL I/O USB 25-PIN D-SUB

Page 6 - DIAGRAM 2: INTERNAL VIEW

SPECIAL APPLICATION 400-0384-003 5 DIAGRAM 2: INTERNAL VIEW ETHERNET RJ-45 USB TX/RXRC-232 RS485 TX/RX TX TX TX TX TX TX TX PDP RX PDP RX VIDEO CARD TX VIDEO CARD EDGE CONNECTORPE 1005 MAIN MP TX OC OC OC OC INPUT CONTROL 11 12 14 13 ADC DETECTOR MONITOR INPUT REAL TIME RELAY CONTROL 3 4 2 1 CONTACT...

Page 7 - DIAGRAM 3: CARD DETAILS; BATTERY

SPECIAL APPLICATION 400-0384-003 6 DIAGRAM 3: CARD DETAILS LED1 BATTERY 3V LithiumCR1225 P3 Test connector used for circuit card evaluation. SW1 RS-232/RS-485 selection. The RS-232 position is shown. P5 Test connector used for circuit card evaluation.

Page 8 - DIAGRAM 5: MOTION DETECTOR DETAILS

SPECIAL APPLICATION 400-0384-003 7 DIAGRAM 4: 25-PIN HD DETAILS PIN Description PIN Description 1 Input 1 5 Relay 1 Throw 2 Input 2 6 Relay 1 Pole 3 Input 3 7 Relay 2 Throw 4 Input 4 8 Relay 2 Pole 9 Relay 3 Throw 10 Relay 3 Pole 11 Relay 4 Throw 12 Relay 4 Pole DIAGRAM 5: MOTION DETECTOR DETAILS PI...

Page 9 - USB SETUP

SPECIAL APPLICATION 400-0384-003 8 INSTALLING YOUR PE1005 6 Step 1. Turn off the power to the plasma display. Step 2. Use ESD safety precautions and always wear a ground strap when handling the PE1005 . Step 3. Prepare the card if necessary using the application diagrams on page 7. Step 4. Remove th...

Page 10 - NOTE: If you want to assign the IP manually, click

SPECIAL APPLICATION 400-0384-003 9 6. Click on the “Search” button to check fornew devices on the LAN. NOTE: If you want to assign the IP manually, click “Assign IP”. This method will require the hardware address on the device and the assistance of your IT Administrator. THE IP ADDRESS 7. Once the d...

Page 11 - OPERATION; DESCRIPTION OF COMMANDS

SPECIAL APPLICATION 400-0384-003 10 OPERATION 7 7.1 RS-232 CONTROL The PE1005 has many advanced remote control capabilities, which are accessible through standard RS-232 communication. Actual controlling may be achieved using a computer control system or other device capable of sending RS-232 comman...

Page 12 - Reset the

SPECIAL APPLICATION 400-0384-003 11 Example: Reset the PE1005 with unit ID 1 to its default settings by sending the command [FRESETC1].The card will display a notice that a reset is in process: PLEASE WAITCARD IS PERFORMING FACTORY RESET When the reset is complete, the following message will be disp...

Page 13 - Ci

SPECIAL APPLICATION 400-0384-003 12 7. [RDRL] This command is used to read the status of one or all of the internal relays. A ‘1’ indicates the relay is on (closed). A ‘0’ indicates the relay is off (open). Command Format: [RDRLnCi] n = Relay No. (1, 2, 3, 4 or * for all) Ci = Unit ID (i = # from 1 ...

Page 21 - Mode 3: When minutes and seconds match 30:00

SPECIAL APPLICATION 400-0384-003 20 ALARM CONTROLS 36. [ALRMON] This command activates Alarm #1 and Alarm #2. After turning the alarm on, the functions assigned to the alarm with the [ALRMn=SUBk] command will be executed at the alarm time. Command Format: [ALRMONnCi] n = Alarm No. (n = 1 or 2) Ci = ...

Page 27 - SUMMARY OF COMMANDS

SPECIAL APPLICATION 400-0384-003 26 REMEMBER: A command sent without the unit ID will be executed by all the PE1005 s connected to the RS-232 port. 66. [SIDnCi] This command sets the ID number of a single card to a new ID number. Only the cards that have the matching ID will be changed. Command Form...

Page 28 - PLASMA CONTROL WITH INTERNAL BUS

SPECIAL APPLICATION 400-0384-003 27 46) [MODERSI] Set internal baud rate 47) [RDRSI] Read internal baud rate 48) [OUTRSM] Send memory data via external RS-232 49) [OUTBSM] Send memory data via internal RS-232 50) [OUTPDPM] Send memory data to plasma main card 51) [OUTVCM] Send memory data to plasma ...

Page 29 - Select Input 1; PIONEER PLASMA COMMANDS; TROUBLESHOOTING GUIDE; THERE IS NO COMMUNICATION

SPECIAL APPLICATION 400-0384-003 28 Example 2: Adjust Brightness Now that the plasma is in adjustment mode, various settings may be changed. Set the brightness to a value of 100 by sending the following commands directly to the internal bus: [SENDBS<%02%2A%2A>][SENDBS<BRT150%03>] NOTE: T...

Page 30 - INPUT PORTS DO NOT RESPOND; The input pin is not grounded.; ALTINEX POLICIES; Please see the ALTINEX website at; CONTACT INFORMATION

SPECIAL APPLICATION 400-0384-003 29 8.3 INPUT PORTS DO NOT RESPOND Cause 1: The input pin is not grounded. Solution : Short the input port to ground using a switch or jumper and send the command [RDI*]. The status of all input ports will be displayed. A ‘1’ is for on (shorted) and a ‘0’ is for off. ...