Altinex PE1004CF - Manuals - manualsarea.com

Page 2 - SPECIAL APPLICATION; TABLE OF CONTENTS

SPECIAL APPLICATION 400-0210-001 1 TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS ............... 2 GENERAL .......................................................... 2 INSTALLATION ................................................. 2 CLEANING.......................................................

Page 3 - PRECAUTIONS / SAFETY WARNINGS

SPECIAL APPLICATION 400-0210-001 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your PE1004CF . Keep this manual handy for future reference. These safety instructions are to ensurethe long life of your PE1004CF and to prevent fire and shock hazard. Please read them ...

Page 4 - TECHNICAL SPECIFICATIONS

SPECIAL APPLICATION 400-0210-001 3 ABOUT YOUR PE1004CF 2 PE1004CF CAT-5 RECEIVER CARD FOR PIONEER PLASMA EXPANSION The PE1004CF CAT-5 Receiver Card is designed to receive RGBHV/YPbPr video and audio signals over twisted pair (CAT-5) type cable. The encoded CAT-5 signals are Altinex Standard Audio+ V...

Page 5 - APPLICATION DIAGRAMS; DIAGRAM 1: INPUT SELECTION

SPECIAL APPLICATION 400-0210-001 4 DESCRIPTION OF PE1004CF 4 APPLICATION DIAGRAMS 5 DIAGRAM 1: INPUT SELECTION AUTOMATIC INPUT SELECTION Selecting plasma Input 3 displays PE1004CF CAT-5 #1 Input image on the plasma Input 3.Selecting plasma Input 4 displays PE1004CF CAT-5 #2 Input image on the plasma...

Page 6 - DIAGRAM 2: TYPICAL SETUP

SPECIAL APPLICATION 400-0210-001 5 DIAGRAM 2: TYPICAL SETUP TYPICAL APPLICATION RS-232 DA1930CT DA1931CT DA1930CT DA1930CT PE1004CF

Page 7 - DIAGRAM 3: INTERNAL VIEW

SPECIAL APPLICATION 400-0210-001 6 DIAGRAM 3: INTERNAL VIEW PE1004CF BLOCK DIAGRAM AUDIO SEPARATOR CLOCK GENERATOR AUDIO MODULATION EDGE CONNECTOR POWER CAT5 RJ45 AUDIO INPUT4 3.5mm STEREO AUDIO POWER SUPPLY CONTROL AUDIO INPUT 1 PAIR4 of UTP + - EDGE CONNECTOR BUS CONTROL CAT5 RJ45 VIDEO INPUT415P ...

Page 8 - DIAGRAM 4: SWITCH SETTINGS

SPECIAL APPLICATION 400-0210-001 7 DIAGRAM 4: SWITCH SETTINGS SW2 EQUALIZATION EQ VIDEO EQUALIZATION Set SW2 to the HW position for hardware equalization. Set SW2 to the SW position for software equalization. HARDWARE CONTROL Install the jumper for default input. POWER UP DEFAULT In this case, CAT-5...

Page 9 - OPERATION; DESCRIPTION OF COMMANDS

SPECIAL APPLICATION 400-0210-001 8 INSTALLING YOUR PE1004CF 6 Step 1. Use ESD safety precautions and always wear a ground strap when handling the PE1004CF expansion card. Step 2. Prepare the card per the drawing in Diagram 4. Set SW2 for either hardware or software equalization control and set the p...

Page 12 - TROUBLESHOOTING GUIDE; Solution

SPECIAL APPLICATION 400-0210-001 11 12. […S] This command will save the configuration command being sent to the PE1004CF into its nonvolatile memory. Example: Equalization If Input 4 is currently the active input, send the command [EQ100S] to save the equalization value of 100 for this input. After ...

Page 13 - Cable connections are incorrect.; ALTINEX POLICY; Please see the Altinex website at; CONTACT INFORMATION

SPECIAL APPLICATION 400-0210-001 12 Cause 3: Cable connections are incorrect. Solution: Make sure that the cables are connected properly. Also, make sure that the continuity and wiring are good. If there is still no sound present, see Cause 4. Cause 4: Destination amplifier has a problem. Solution 1...