Altinex MX2226AT - Manuals - manualsarea.com

Page 2 - SWITCHERS; TABLE OF CONTENTS; Page

SWITCHERS 1 1 TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS .............. 2 GENERAL ......................................................... 2 INSTALLATION ................................................. 2 CLEANING ........................................................ 2 FCC / CE NOTICE...

Page 3 - PRECAUTIONS / SAFETY WARNINGS

SWITCHERS 2 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your MX2226AT Switcher. Keep this manual handy for future reference. These safety instructions are toensure the long life of your MX2226AT and to prevent fire and shock hazard. Please read themcarefully and ...

Page 4 - ABOUT YOUR SWITCHER

SWITCHERS 3 3 • Any changes or modifications to the unit notexpressly approved by ALTINEX, Inc. couldvoid the user’s authority to operate theequipment. ABOUT YOUR SWITCHER 2 The MX2226AT , a 6-in 1-out RGBHV Switcher is controllable using its built-in front panel or viaRS-232 commands. The MX2226AT ...

Page 5 - Output Sync Signal; DESCRIPTION OF MODEL NAME

SWITCHERS 4 4 (pass-through) Output Sync Signal Composite Sync TTL(+/-), Analog 0.3-1.0V (unbuffered) Sync on Green -0.3V Impedance Pass-through Frequency Compatibility Typical Video Bandwidth 400 MHz @ -3 dB Horizontal 15-200 kHz Vertical 30-190 Hz Horizontal Position Range 20 % Cross-talk -48 dB @...

Page 6 - APPLICATION DIAGRAM

Page 7 - INSTALLING YOUR SWITCHER

SWITCHERS 6 6 INSTALLING YOUR SWITCHER 6 Step 1 . Make sure that the window on the fuse is set to the proper AC voltage in yourcountry. An incorrect setting can result inunit damage, which is not covered bywarranty. Step 2 . Connect the power cord to the unit and plug it into the power outlet. Make ...

Page 9 - Description

SWITCHERS 8 8 5 GND RS-232 connection of PC with DB-9 port MX2226AT Terminal Block PC DB-25 port pin no. IBM PIN No. MX2226AT Terminal block pin 2 RX 3 TX 7 GND RS-232 connection to MX2226AT Terminal Block of PC with DB-25 port Port settings of the control system or computerbeing used to control the...

Page 10 - Terminal block pin; FREQUENTLY ASKED QUESTIONS

SWITCHERS 9 9 7.5 MASTER/SLAVE CONTROL (RS-232): The feedback codes allow multiple MX2226AT Switchers to be connected in a Master-Slaveconfiguration, if desired. When the control port of two units are connectedas shown below, the slave unit duplicates theactions of the master unit. The slave unit ca...

Page 11 - CABLES AND ACCESSORIES

SWITCHERS 10 10 Why? OFF mode. 3 Can the MX2226AT be used topassCompositeVideo,S-Video, andComponentVideo? Yes, simply use thecorresponding channels topass the signals (e.g. Forcomposite video, you mayuse the red channel or youmay use the blue channel).Since the MX2226AT is a relay switcher, it can ...

Page 12 - SUPER HIGH RESOLUTION 5 BNC TO 5 BNC; CHANNEL COAX CABLE; TROUBLE SHOOTING GUIDE

SWITCHERS 11 11 CB4206MR 6 feet, 5-BNC M to 5-BNC M CB4212MR 12 feet, 5-BNC M to 5-BNC M CB4225MR 25 feet, 5-BNC M to 5-BNC M CB4250MR 50 feet, 5-BNC M to 5-BNC M CB4275MR 75 feet, 5-BNC M to 5-BNC M CB42100MR 100 feet, 5-BNC M to 5-BNC M CB42150MR 150 feet, 5-BNC M to 5-BNC M SUPER HIGH RESOLUTION ...

Page 13 - is connected to the TX pin of; ALTINEX POLICY; LIMITED WARRANTY

SWITCHERS 12 12 www.altinex.com . When using RS-232 commands to the switcher where the RX pin ofthe MX2226AT is connected to the TX pin of the computer, make sure that the cable ismade according to the manual. ALTINEX POLICY 11 11.1 LIMITED WARRANTY ALTINEX warrants that its products and cablesare f...