Altinex MT110-101 - Manuals

Page 2 - MULTITASKERTM; TABLE OF CONTENTS

MULTITASKER™ 400-0197-005 1 1 TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS ............... 2 GENERAL .......................................................... 2 INSTALLATION ................................................. 2 CLEANING............................................................

Page 3 - PRECAUTIONS / SAFETY WARNINGS

MULTITASKER™ 400-0197-005 2 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your MT110-101/103 . Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MT110-101/103 and to prevent fire and shock hazard. Please read...

Page 4 - TECHNICAL SPECIFICATIONS

MULTITASKER™ 400-0197-005 3 3 ABOUT YOUR MT110-101/103 2 The MT110-101/103 is a Balanced Audio Matrix Switching Card. This card allows any input to be independently switched to any of the outputs. All inputs and outputs can be wired for unbalanced audio, or balanced audio allowing longer cable runs ...

Page 6 - APPLICATION DIAGRAM; Diagram 1: Typical Setup

MULTITASKER™ 400-0197-005 5 5 APPLICATION DIAGRAM 5 Diagram 1: Typical Setup

Page 9 - OPERATION; Use uppercase letters for all commands.

MULTITASKER™ 400-0197-005 8 8 INSTALLING YOUR MT110-101/103 6 Step 1. Turn off power to the MultiTasker™ enclosure. Step 2. Slide the MT110-101/103 into an available slot in the MultiTasker™ Basic Enclosure in order to connect to the bus. Make sure that the MT110-101/103 card fits into place. Secure...

Page 11 - = Matrix Configuration

MULTITASKER™ 400-0197-005 10 10 Example: If Input 1 is connected to all outputs, but only 1 through 4 are on, the feedback after sending the command [C4S], for slot 4, would be similar to the following: CONFIGURATION:Matrix:8x8, In-Offset=0, Out-Offset=0CONNECTION OUTPUT VOLUME In01-Out01 ON 32/32 I...

Page 15 - Ui

MULTITASKER™ 400-0197-005 14 14 Command Format: [ImO * CnUi] m = Input (m = # from 1 to 8) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Connect Input 1 to all outputs for the MT110-103 in slot 5. Send the command [I1O*C5] and Input 1 will be connected to al...

Page 16 - Ci

MULTITASKER™ 400-0197-005 15 15 ID COMMANDS: RSI, SIDn, SIDnCi, SID+, RSN The default Card ID is the same as the card slot number. The next several commands allow the user to change the Card ID to a value other than the slot number. Once the ID is changed, moving the card to another slot will not ch...

Page 22 - There is an

MULTITASKER™ 400-0197-005 21 21 42. [RAMP=x] MT110-103 ONLY This command sets the ramp rate for 32 steps. The settings range from 4 to 18 seconds, in two-second intervals. Command Format: [RAMP=xCnUi] x = Rate in Seconds 4 = 0.13 seconds/step 6 = 0.19 seconds /step 8 = 0.25 seconds /step 10 = 0.31 s...

Page 24 - TROUBLESHOOTING GUIDE; we would like to offer suggestions for the following:

MULTITASKER™ 400-0197-005 23 23 32) [ + ] Increment volume 33) [ - ] Decrement volume 34) [RUP] Ramp UP to max (32) 35) [RDN] Ramp DOWN to mon (0) 36) [RUPm] Ramp volume UP to max (32) 37) [RUPm=] Ramp volume UP to a value 38) [RDNm] Ramp volume DOWN to min (1) 39) [RDNm=] Ramp volume DOWN to a valu...

Page 25 - Solution 2

MULTITASKER™ 400-0197-005 24 24 Cause 2: The card and its serial device are not communicating. Solution 1: Turn the system off and then onagain. If there is still an error, see Cause 3. Cause 3: RS485 communication error Solution 1: Make sure that the card is pushed all the way into the slot. If the...

Page 26 - ALTINEX POLICY; Please see the Altinex website at; CONTACT INFORMATION

MULTITASKER™ 400-0197-005 25 25 ALTINEX POLICY 9 9.1 LIMITED WARRANTY/RETURN POLICY Please see the Altinex website at www.altinex.com for details on warranty and return policies. 9.2 CONTACT INFORMATION ALTINEX, Inc. 592 Apollo Street Brea, CA 92821 USA TEL: 714 990-2300 TOLL FREE: 1-800-ALTINEX FAX...