Altinex MT108-102 - Manuals

Page 2 - MULTI-TASKER; TABLE OF CONTENTS; Page

MULTI-TASKER 1 TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS .............. 2 1.1 GENERAL ................................................... 2 1.2 INSTALLATION .......................................... 2 1.3 CLEANING.................................................. 2 1.4 FCC / CE NOTICE .....

Page 3 - PRECAUTIONS / SAFETY WARNINGS

MULTI-TASKER 2 PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your MT108-102/(103) Distribution Amplifier. Keep this manual handy for future reference. These safetyinstructions are to ensure the long life of your MT108-102/(103) and to prevent fire and shock hazard. P...

Page 4 - TECHNICAL SPECIFICATIONS; MECHANICAL

MULTI-TASKER 3 ABOUT YOUR MT108-102/(103) 2 MT108-102/(103)1-in 4-out Stereo Audio DistributionAmplifier Cards The MT108-102 and MT108-103 are Stereo, Audio Distribution Amplifier Cards designed for use withthe Multi-Tasker  system. When installed in a Multi-Tasker  , these cards allow the connect...

Page 5 - APPLICATION DIAGRAM; Application 1

MULTI-TASKER 4 DESCRIPTION OF MT108-102/(103) 4 APPLICATION DIAGRAM 5 Application 1

Page 7 - Use uppercase letters for all commands.

MULTI-TASKER 6 INSTALLING YOUR MT108-102/(103) 6 Step 1. Slide the MT108-102/(103) into an available slot in the Multi-Tasker™ BasicEnclosure in order to connect to the bus.Make sure that the MT108-102/(103) Stereo Audio DA Card fits into place. Secure the card to the Multi-Tasker™ bytightening the ...

Page 8 - refer to the

MULTI-TASKER 7 Ui = Unit ID (i = # from 0 to 9) ( refer to the MT100-100 user’s guide for explanation) Example: If one MT108-103 card is plugged in slot #2 of unit 3: Sending the command [VERC2U3] , will yield the following feedback from theMulti-Tasker™ MT108-103 690-0127-007 MT108-103 = card type ...

Page 9 - PF

MULTI-TASKER 8 Example: 1. [ON1G5U1] : Turns ON output 1 for each card in group 5 of unit 1. 2. [ONG5U1] : Turns ON all outputs for each card in group 5 of unit 1. [ON…P]: sets path This command will set the path for the output,but it is not active until the switch command,[SW], is executed. Command...

Page 10 - If 2 cards are in slots 6 and 7 of unit 3:; command or the [OFFmCnUi; FP

MULTI-TASKER 9 Example: If 2 cards are in slots 6 and 7 of unit 3: To disable outputs 1 and 2 of card 6 andoutputs 3 and 4 of card 7 simultaneously, usethe following commands: [OFF12C6U3 P ] [OFF34C7U3 P ] [SW ] If "F" is included use the [OFFmCnUi PF ] command or the [OFFmCnUi FP ] command....

Page 11 - will return feedback as

MULTI-TASKER 10 14. [G] This command is used to request group data.With the command, the user can identify whichinput or output of a particular group is on. Command Format: [GkUi] k = group number (k = # from 1-9) i = unit number (i = # from 0-9) Example: If group 1 has DA Cards with outputs 1 and 2...

Page 12 - TROUBLESHOOTING GUIDE; SOUND DISTORTION

MULTI-TASKER 11 TROUBLESHOOTING GUIDE 8 We have carefully tested and have found noproblems in the supplied MT108-102/(103) ; however, we would like to offer suggestions for thefollowing : 8.1 LED IS NOT LIT Cause 1: Card cage is not plugged in. Solution: Plug card cage in. If the LED lights,the prob...

Page 13 - SOUND LEVEL IS LOW; ALTINEX POLICY; CONTACT INFORMATION

MULTI-TASKER 12 8.4 SOUND LEVEL IS LOW Cause 1: The volume levels are inappropriate. Solution 1: Turn up the source volume. If sound level is still low, see Solution 2. Solution 2: Turn up the destination amplifier volume. If the sound level is still low,see Cause 2. Cause 2: Poor signal transmissio...