Alpine SPX-F17M - Manuals - manualsarea.com

Page 2 - Attention; Points to Observe for Safe Usage; Caution; Warning; Points à respecter pour une utilisation sûre; Avis

2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LESINSTALLER CORRECTEMENT. L’utilisation d’autrespièces non désignées risque de provoquer desdommages à l’intérieur de l’appareil ou son installa-tion risque de ne pas être faite correctement, et lespièces desserrées peuvent provoquer des dangers. NE...

Page 3 - Grille ring / Collier da la grille ................................................; For Tweeter Mounting / Pour le Montage du tweeter; System Contents / Contenu du système

3 19. Screw st4.2x9.5mm / Vis st4.2x9.5 mm …………….......………. x1 20. Screw st4.2x19mm / Vis st4.2x19 mm ...………………...……… x2 21. Screw st4.2x19mm / Vis st4.2x19 mm .........……………………… x1 22. Wing nut M4 / Écrou à oreilles M4 ....……………………………… x1 For Network Mounting / Pour le montage du filtre 23. Crossov...

Page 5 - Attach gasket tape as shown, then lock speaker into grille ring.; Installation; Fixez le cordon isolant comme indiqué sur l'illustration.

5 Installation Woofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ringmust be removed for proper fit. st4.2x25mm Woofer: Flush mount Notes: l Attach gasket tape as shown. l Carefully cut openin...

Page 7 - Attach gasket tape as shown.; Tweeter : Montage tronqué en surface

7 Installation Woofer: Factory/Size-down Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break awayany unused tabs. Hardware: l Use st4.2x25mm for adapter to vehicle l Use M4x10mm for speaker to adapter (adapter only) l Use M4x18mm for speaker to adapter (ad...

Page 8 - Pass wires through terminal cover and connect to terminals.; Press mounting clips at center and secure with screw.; Tweeter : Montage à niveau; Appuyez sur les attaches au centre et fixez à l'aide d'une vis.

8 Tweeter: Flush mount Notes: l Pass wires through terminal cover and connect to terminals. l Press terminal cover snuggly over tweeter housing, making sure connectionsare not exposed. l Attach mounting spring, adjusting screw depth and spring tension as needed.Do not over tighten. Wing nut M4 M4x25...

Page 9 - Single Input; Remettez le cache du filtre en place.; Entrée simple

9 Notes: l Remove network cover, and secure base asshown. l Connect wires to terminal blocks accordingly.(see System Connection Diagrams section) l Make appropriate jumper settings usingjumper puller tool.(see Crossover Network Settings section) l Re-secure network cover. Crossover Network Setting I...

Page 19 - Description du filtre :

19 Crossover Network Settings System Type 4 Filter Description:Fully active systems have often been considered to be the most flexible, but they arecertainly not the most effective in all cases. While it is usually considered best to haveindividual channels of amplification for each driver, it may n...

Page 20 - Sealed box; Système; Specifications; Designed by Alpine Electronics of America, Inc.

System Type Component 2-way speaker Power Handling (peak/RMS) 300/75W Impedance 4 W Frequency Response 30-35 kHz Net Weight 2.5 kg Drivers GeneralSpeaker size 6,5” 28 mm Speaker Type Woofer/Midrange Tweeter Power Handling (RMS) 75 W 150 W Voice Coil Impedance (nom) 4 W 4 W Frequency Response (-10dB)...