Alpine SPX-177A - Manuals - manualsarea.com

Page 2 - Attention; Points to Observe for Safe Usage; Caution; Warning; Points à respecter pour une utilisation sûre; Avis

2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LESINSTALLER CORRECTEMENT. L’utilisation d’autrespièces non désignées risque de provoquer desdommages à l’intérieur de l’appareil ou son installa-tion risque de ne pas être faite correctement, et lespièces desserrées peuvent provoquer des dangers. NE...

Page 3 - System Contents / Contenu du système

3 19. Fixed-flush mount cup / Embase fixe à niveau …………………… x2 20. Mounting clip / Attache de montage .....…………………………. x4 21. Swivel-spacer / Swivel-spacer .....………… ………………. x4 22. Screw st4.2x9.5mm / Vis st4.2x9.5mm....…………………….. x2 23. Screw st4.2x19mm / Vis st4.2x19mm….....………………….. x4 24. Screw ...

Page 5 - Woofer: Surface mount; Attach gasket tape as shown.; Installation; Woofer : Montage en surface; Fixez le cordon isolant comme indiqué sur l'illustration.

5 Installation (SPX-177A) Woofer: Surface mount Woofer: Factory/stealth Notes: l Attach gasket tape as shown. l If spacer ring is used with grille, snap-fit tabs on spacer ringmust be removed for proper fit. st4.2x25mm Notes: l Attach gasket tape as shown. st4.2x25mm Installation (SPX-177A) Woofer :...

Page 11 - Remettez le cache du filtre en place.; Filtre de voies

11 Installation Tweeter: Surface-angle mount Notes: l Remove network cover, and mount asshown l Connect wires to terminal blocksaccordingly.(see System Connection Diagrams section) l Make appropriate jumper settings usingjumper puller tool(see Crossover Network Settings section) l Re-secure network ...

Page 12 - System Connections; Single Input; Connexions du système; Entrée simple

12 System Connections Single Input Bi-wire Input Note:Signal link jumpers highlighted in black must be inserted for proper function of singleinput configuration. Wiring for connection of crossover network to amplifier is notincluded.Caution: These jumpers must be removed when using b-wire input. Con...

Page 13 - Crossover Network Settings; Configuration du filtre de voies; Introduction

13 Crossover Network Settings It is common knowledge that the automotive environment poses numerous acoustic challenges toachieving high-fidelity sound. Fortunately, many of these problems can be overcome with properspeaker placement, equalization, digital time correction, or other techniques. Howev...

Page 14 - Kick-Panel or Flat Baffle; fonctionnement de cette configuration.

14 Crossover Network Settings System Type 1 (default) Speaker Placement Description:In this system type, woofer and tweeter are mounted in close proximity to each other,and are mounted in essentially the same plane. Due to positioning limitations in someapplications, additional tuning may be require...

Page 15 - System Type 1; Type de système 1

15 Crossover Network Settings System Type 1 Filter Description:In this setting, the woofer and tweeter are at approximately equal distance fromthe listener. Using the kick-panel for placement is only one of many locationsavailable to mount both drivers together. What is important is that but by put-...

Page 16 - System Type 2; Level and Axis; Type de système 2; Montant

16 Crossover Network Settings System Type 2 Speaker Placement Description:In this system type, woofer and tweeter are mounted different locations and at differentdistances from the listener. Also of significance, is the fact that the tweeter is thenearest driver. All component locations listed below...

Page 19 - System

19 Specifications Specifications System SPX-177A SPX-137A Type Component 2-way speaker Component 2-way speaker Power Handling (peak/RMS) 240/60 W 200/50 W Impedance 4 W 4 W Frequency Response 35-35 kHz 35-35 kHz Net Weight 5 kg 4.5 kg Drivers GeneralSpeaker size 6.5” (SPX-177A) 5.25” (SPX-137A) 26 m...