Allied Telesis Switch Controller - Manuals

Page 3 - Quick Install Guide; Models Covered By This Guide; AT-SB4211 Switch Controller; Package Contents; One SwitchBlade Switch Controller.; Documentation Roadmap

Quick Install Guide 3 C613-04031-01 REV B Models Covered By This Guide This Quick Install Guide includes information on installing the following card: ■ AT-SB4211 Switch Controller Information on installing line cards can be found in the SwitchBlade Line Card Quick Install Guide . Quick Install Guid...

Page 4 - SwitchBlade Switch Controller; Related items that can be purchased separately:; Installing A Switch Controller; Follow these steps to install a switch controller:; Read the safety information; For safety information, see the; Gather the tools and equipment you will need

4 SwitchBlade Switch Controller C613-04031-01 REV B Related items that can be purchased separately: ■ CPU memory pack, 256 MByte DRAM (2 x 128 MByte DIMMs). ■ SwitchCAM (Content Addressable Memory) for enhanced L2/L3 forwarding-database table size, 128 k-entry modules. ■ Blank faceplates for switch ...

Page 5 - In an antistatic environment:; Figure 2: Installing DIMM on the AT-SB4211 Switch Controller.; CAM Quick Install Guide

Quick Install Guide 5 C613-04031-01 REV B Figure 1: ESD socket on the SwitchBlade 8 chassis. 5. Install the CPU memory pack Only Allied Telesyn supplied DIMMS have been tested and approved for use with SwitchBlade switch controllers. Using DIMM that has not been approved may cause unreliable operati...

Page 6 - To remove a bay’s faceplate:; Insert the new switch controller

6 SwitchBlade Switch Controller C613-04031-01 REV B 7. Prepare the switch controller bay Remove the switch controller bay faceplate or existing switch controller To remove a bay’s faceplate: Loosen the faceplate’s two Phillips mounting screws until they disengage from the chassis, then remove the fa...

Page 7 - If the power LED fails to light:; Extractor lever

Quick Install Guide 7 C613-04031-01 REV B When inserting a switch controller, take care to slide the back-panel along both guides at an equal rate. If a switch controller becomes tight, it must not be forced. Instead, gently withdraw the controller and try again, taking extra care to keep the contro...

Page 8 - Configuring The Switch Controller; Using the CLI to configure a switch controller:; Set the communication parameters; SwitchBlade Hardware Reference

8 SwitchBlade Switch Controller C613-04031-01 REV B For DC chassis models, ensure that: • The correct DC terminal blocks on the chassis’s rear panel are wired. The blocks should correspond to PSU bays that have PSUs installed. • The DC terminals are wired to the correct polarity. • The circuit break...

Page 9 - Load help files; SwitchBlade Software Reference; Using the GUI to configure a switch controller

Quick Install Guide 9 C613-04031-01 REV B 3. Check the power supply Ensure the chassis’s standby switch is in the Run position and the switch controller is receiving power (Power LED lights green). 4. Log in After the switch controller has booted, the log in prompt appears. If the log in prompt does...

Page 10 - Connect a PC to ETH0; The PC should be running Internet Explorer version 5.; Access the GUI; At the log in prompt, enter the log in name and password.; To access context-sensitive help

10 SwitchBlade Switch Controller C613-04031-01 REV B For instructions on using ASYN0 and the CLI to change ETH0’s IP address, see the “Graphical User Interface” section in the “Operations” chapter of the SwitchBlade Software Reference . 1. Connect a PC to ETH0 Use a straight-through Ethernet patch c...

Page 11 - Switch Controller LEDs; The; LED

Quick Install Guide 11 C613-04031-01 REV B Switch Controller LEDs The following LEDs will operate if the switch controller is receiving power. The SwitchBlade Hardware Reference has further troubleshooting information, including information on line card and power supply unit LEDs. Table 1: LEDs on t...

Page 12 - Documentation And Tools CD-ROM

12 SwitchBlade Switch Controller C613-04031-01 REV B Documentation And Tools CD-ROM The Documentation and Tools CD-ROM bundled with every switch controller and every chassis contains the complete Documentation Set for your switch and its expansion options, as well as tools for managing the switch. T...