Allied Telesis R800 Series - Manuals

Page 2 - Patch Release Note; A byte of data from FLASH was incorrectly returning the value 0xFF.; Network affecting: No

2 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U Features in 86222-22 The firewall was blocking outbound ICMP packets when the associated private interface had a ‘deny all’ rule. The passing of ICMP packets should be controlled by the ICMP_FORWARDING and PING parame...

Page 4 - The source net mask has been removed from DVMRP; Base Software Release File

4 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U When the switch was under heavy learning load, some MAC address were lost. This issue has been resolved. In the ADD IP ROUTE FILTER command, when the optional parameter INTERFACE was included, the filter was not appli...

Page 6 - Patch file details for Patch 86222-20 are listed in Table 3:

6 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U Features in 86222-20 Patch file details for Patch 86222-20 are listed in Table 3: Patch 86222-20 includes all issues resolved and enhancements released in previous patches for Software Release 2.2.2, and the following...

Page 8 - The PURGE IP command now resets the IP route cache counters to zero.

8 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U When the only feature licence in the feature licence file was disabled, the licence file stored on FLASH memory did not change. This was due to a previous enhancement in PCR 02184 which prevented existing files being ...

Page 10 - Patch file details for Patch 86222-19 are listed in Table 4:

10 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U VRRP used the wrong source IP address in ICMP redirects. RFC 2338 states that the source IP address of ICMP redirects should be the IP address that the end host used when making its next hop routing decision. In the ...

Page 12 - Patch file details for Patch 86222-18 are listed in Table 5:

12 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U Features in 86222-18 Patch file details for Patch 86222-18 are listed in Table 5: There is no patch release 86222-17 because this patch was withdrawn. Patch 86222-18 includes all issues resolved and enhancements rele...

Page 13 - Patch file details for Patch 86222-16 are listed in Table 6:

Patch 86222-22 For Rapier Switches and AR800 Series Modular Switching Routers 13 Patch 86222-22 for Software Release 2.2.2C613-10319-00 REV U Port mirroring on the Rapier 48 and 48i was not operating correctly because Destination Lookup Failure (DLF) frames were sent from the mirror port. This issue...

Page 14 - Patch file details for Patch 86222-15 are listed in Table 7:

14 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U A switch sometimes restarted if it was configured with static DHCP entries and was handling a large number of DHCP clients. This issue has been resolved. Features in 86222-15 Patch file details for Patch 86222-15 are...

Page 19 - Patch file details for Patch 86222-11 are listed in Table 11.

Patch 86222-22 For Rapier Switches and AR800 Series Modular Switching Routers 19 Patch 86222-22 for Software Release 2.2.2C613-10319-00 REV U The first periodic after day trigger boundary (i.e. midnight) did not occur. A range check error occurred due to an incorrect comparison. These issues have be...

Page 20 - ENABLE SWI STPFORWARD

20 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U Features in 86222-10 Patch file details for Patch 86222-10 are listed in Table 12. Table 12: Patch file details for Patch 86222-10. Patch 86222-10 includes all issues resolved and enhancements released in previous pa...

Page 21 - Patch file details for Patch 86222-08 are listed in Table 14.

Patch 86222-22 For Rapier Switches and AR800 Series Modular Switching Routers 21 Patch 86222-22 for Software Release 2.2.2C613-10319-00 REV U The default setting for the switch port parameter INFILTERING is now OFF, as specified in IEEE802.1Q. A VLAN will still reject these packets if they are not f...

Page 22 - The dot1dBridge MIB implementation now complies with RFC1493.

22 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U When IGMP snooping was enabled, if a member left a group on a port, it could not re-join the group on that port. This issue has been resolved. Substantial changes have been made to PIM in more recent code releases. T...

Page 23 - MD5 Authentication now works correctly with RIP packets.

Patch 86222-22 For Rapier Switches and AR800 Series Modular Switching Routers 23 Patch 86222-22 for Software Release 2.2.2C613-10319-00 REV U MD5 Authentication now works correctly with RIP packets. The SET IP LOCAL command caused a fatal error if the router was configured with a default route over ...

Page 24 - triggerLastTriggerActivated

24 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U In some conditions it was possible for ISAKMP packets to be lost and not retransmitted. Incoming ISAKMP messages are now validated before stopping retransmission of the previous message. The COS_DST bit on ARL for L3...

Page 25 - Patch file details for Patch 86222-06 are listed in Table 16.

Patch 86222-22 For Rapier Switches and AR800 Series Modular Switching Routers 25 Patch 86222-22 for Software Release 2.2.2C613-10319-00 REV U The CREATE CONFIG command did not include all required L3FILTER parameters in the generated script file. The L3 table on the Rapier G6 is now cleared when a s...

Page 30 - Availability; licence or password is not required to use a patch.

30 Patch Release Note Patch 86222-22 for Software Release 2.2.2 C613-10319-00 REV U Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html . A licence or password is not required to use a patch.