Allied Telesis AT-X210-16GT - Manuals

v Figures Figure 1: AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT packaging .............................................................................. 8Figure 2: AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Front Panels .......................................................................... 9Fig...

vii Tables Table 1. AT-x210-9GT POWER LED Functional Descriptions .......................................................................................... 13Table 2. AT-x210-16GT and AT-x210-24GT FAULT LED Functional Descriptions .......................................................... 14Table 3...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 1 Preface This guide contains the installation instructions for the AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Gigabit Ethernet Switches. This preface contains the following sections: ˆ “Symbol Conventions” on page 2 ˆ “Contact...

2 Symbol Conventions This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific a...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 3 Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/suppor...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 5 Chapter 1 Overview This chapter provides descriptions of the AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Gigabit Ethernet Switches and contains the following sections: ˆ “Features” on page 6 ˆ “Package Contents” on page 8 ˆ “F...

Chapter 1: Overview 6 Features Here are the hardware features of the AT-x210-9GT, AT-x210-16GT and AT-x210-24GT Gigabit Ethernet Switches. Twisted Pair Ports Here are the basic features of the 10/100/1000 Mbps twisted-pair ports: „ 9, 16, or 24 ports per switch „ 10Base-T (IEEE 802.3i), 100Base-TX (...

Chapter 1: Overview 8 Package Contents Figure 1 illustrates the package contents for the AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Gigabit Ethernet Switches. Figure 1. AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT packaging 1 Power Cable (1.8m) AT-x210-16GT/AT-x210-24GT 1 x 19” rack mount kit 1 Powe...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 9 Front and Back Panels Figure 2 illustrates the front panels of the AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Gigabit Ethernet Switches. Figure 2. AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Front Panels 1 3 5 7 2 4 6 8 FAULT...

Chapter 1: Overview 10 Figure 3 illustrates the MODE LED toggle button on the front panel of the of the AT-x210-9GT and AT-x210-16GT Gigabit Ethernet Switches. This button changes front panel LEDs for SPEED, DUPLEX, or turns off LEDs. Figure 3. MODE LED Toggle button Figure 4 illustrates the front p...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 11 Management Software The switches are shipped with the management software pre-installed. The software provides a command line interface and a GUI (Graphical User Interface) for in-band, over-the-network management. Refer to t...

Chapter 1: Overview 12 Twisted Pair Ports The AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Layer 2 Gigabit Ethernet Switches feature 9, 16, and 24 twisted pair ports, respectively. All ports are 10Base-T, 100Base-TX, and 1000Base-T compliant. You can set the port speeds and duplex modes either automa...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 13 LEDs There are four types of LEDs on the AT-x210 switches: ˆ “POWER/FAULT/STANDBY LEDs” on page 13 ˆ “10Base-T/100Base-TX/1000 Base-T Link Activity LEDs” on page 15 ˆ “SFP LEDs” on page 17 POWER/ FAULT/ STANDBY LEDs The POWER...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 15 10Base-T/ 100Base-TX/1000 Base-T Link Activity LEDs The Link Activity (L/A) LEDs provide information about the 10Base-T/100Base-TX/1000Base-T ports. AT-x210-9GT Link/Activity and Speed LEDs The AT-x210-9GT switch indicates LI...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 17 See Table 5 for a description for the AT-x210-16GT and AT-x210-24GT Link/Activity and Speed LEDs. Table 5. AT-x210-16GT and AT-x210-24GT LINK/ACT and SPEED/ DUPLEX LED Descriptions . SFP LEDs The SFP LEDs indicate the Link/Ac...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 19 Power Supply Each switch has an internal power supply with a single AC power supply socket on the back panel. To power the switch on or off, connect or disconnect the power cord provided with the switch. A power cord is suppl...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 21 Chapter 2 Installation This chapter contains the following sections: ˆ “Reviewing Safety Precautions” on page 22 ˆ “Selecting a Site for the Switch” on page 24 ˆ “Cable Specifications” on page 25 ˆ “Unpacking the Switch” on p...

Chapter 2: Installation 22 Reviewing Safety Precautions Please review the following safety precautions before you begin to install the chassis or any of its components. Note The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements . ...

Chapter 2: Installation 24 Selecting a Site for the Switch Observe the following requirements when choosing a site for your switch: „ If you plan to install the switch in an equipment rack, verify that the rack is safely secured and will not tip over. Devices in a rack should be installed starting a...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 25 Cable Specifications Table 7 contains the cable specifications for the twisted pair ports. Note The twisted pair ports on the switch feature auto-MDI when operating at 10, 100, or 1000 Mbps. A port is configured as MDI or MDI...

Chapter 2: Installation 26 Unpacking the Switch To unpack the switch, perform the following procedure: 1. Remove all of the components from the shipping package. Note Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 27 Installing the Switch on a Table or a Desktop You can install AT-x210-16GT and AT-x210-24GT switches on a desktop, or in a standard 19-inch equipment rack. To install AT-x210-16GT and AT-x210-24GT switches in a rack, see “Ins...

Chapter 2: Installation 28 Installing the Switch in an Equipment Rack Note: These instructions show you how to install an AT-x210-9GT, AT-x210-16GT or AT-x210-24GT switch in an equipment rack. Rack mount kit brackets are included with AT-x210-16GT and AT-x210-24GT switches. The AT-x210-9GT switch is...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 29 4. Mount an AT-x210-24GT switch in a 19-inch equipment rack using four equipment rack screws (not provided with the switch). Figure 17. Mounting an AT-x210-24GT Switch in an Equipment Rack 5 7 6 8 9 11 13 15R 10 12 14 16R 17 ...

Chapter 2: Installation 30 5. For AT-x210-16GT Switches, attach the two rack mount brackets to the sides of the switch using the bracket screws that come with the unit. See the bracket position as shown in Figure 18 and Figure 19. Figure 18. Attaching the brackets level with the front of an AT-x210-...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 31 6. Mount an AT-x210-16GT switch in a 19-inch equipment rack using the provided spacer bracket mounts with four equipment rack screws (not provided with the switch), as shown in Figure 20. Figure 20. Mounting an AT-x210-16GT S...

Chapter 2: Installation 32 7. For AT-x210-9GT switches, first fit the rack mount handles to the brackets using the supplied M3x6mm pan head screws, as shown below in Figure 21. Figure 21. Fitting rack mount handles to the brackets for an AT-x210-9GT 8. After fitting the rack mount handles to the bra...

Chapter 2: Installation 34 11. Mount an AT-x210-9GT switch in a 19-inch equipment rack using the provided spacer bracket mounts with four equipment rack screws, as shown in Figure 25. Figure 25. Mounting an AT-x210-9GT Switch in an Equipment Rack 12. Secure cables to the cable tray fitted earlier, a...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 35 Installing Optional SFP Transceivers To install an SFP transceiver, perform the following procedure: Note The transceiver can be hot-swapped; you do not need to power off the switch to install a transceiver. However, always r...

Chapter 2: Installation 36 4. For an AT-x210-24GT Switch, gently slide the transceiver into the SFP slot until it clicks into place, as shown in Figure 28. Figure 28. Inserting the SFP on an AT-x210-24GT 5. For an AT-x210-16GT Switch, gently slide the transceiver into the SFP slot until it clicks in...

Chapter 2: Installation 38 Note SFP transceivers are dust sensitive. Always keep the plug in the optical bores when a fiber optic cable is not installed, or when storing the SFP. When you do remove the plug, keep it for future use. Note Unnecessary removal and insertion of an SFP can lead to prematu...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 39 Cabling the Switch Observe the following guidelines when connecting twisted pair and fiber optic cables to the ports on the switch: „ The connector on the cable should fit snugly into the port on the switch. The tab on the co...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 41 Powering On the Switch To power on the AT-x210-24GT, AT-x210-16GT, or AT-x210-9GT switch, perform the following procedure: 1. Plug the power cord into the AC power connector, as shown in Figure 32 on the back of an AT-x210-16...

Chapter 2: Installation 42 Warning Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. E3 Pluggable Equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. E5 4. Verify that the POWER LED is green. If the LED i...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 43 Monitoring the Initialization Processes It takes about thirty seconds for the switch to initialize its management software programs and features, and load the default configuration. You may also monitor the bootup sequence by...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 47 Chapter 3 Troubleshooting This chapter contains information on how to troubleshoot the switch if a problem occurs. Note For further assistance, please contact Allied Telesis Technical Support at www.alliedtelesis.com/support ...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 49 Problem 5: A port’s LINK/ACT LED is blinking. Solutions: The link between the port and the network device is intermittent. Try the following: „ Connect another network device with a different cable to the port. If the Link LE...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 51 Appendix A Technical Specifications

Appendix A: Technical Specifications 52 Physical Specifications Dimensions Weight Environmental Specifications Table 8. Chassis Dimensions Model W x D x H mm (in) AT-x210-9GT 263 mm x 179 mm x 38 mm (10.35 in x 7.05 in x 1.50 in) AT-x210-16GT 341 mm x 210 mm x 44 mm (13.42 in x 8.26 in x 1.73 in) AT...

AT-x210-9GT, AT-x210-16GT, and AT-x210-24GT Switches Installation Guide 53 Power Specifications Input Supply Voltage - 100-240 VAC, 50 - 60 Hz Electrical Safety and Electromagnetic Emissions Certifications Table 11. Power Specifications AT-x210-9GT 12 W AT-x210-16GT 19 W AT-x210-24GT 28 W Table 12. ...

Appendix A: Technical Specifications 54 Connectors and Port Pinouts This section lists the connectors and connector pinouts. Figure 37 illustrates the pin layout for an RJ-45 connector and port. Figure 37. RJ-45 Connector and Port Pin Layout Table 13 lists the RJ-45 pin signals when a twisted pair p...