Allied Telesis AT-FS708LE - Manuals

10 Caution Cautions informs you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings informs you that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn This section provides Allied Telesyn contact...

AT-FS708LE Installation Guide 11 E-mail and Telephone Support For Technical Support via E-mail or telephone, refer to the Support & Services section of the Allied Telesyn web site: http://www.alliedtelesyn.com. Returning Products Products for return or repair must first be assigned a Return Mate...

13 AT-FS708LE Fast Ethernet Switch Overview The AT-FS708LE unit is a 10Base-T/100Base-TX Fast Ethernet Switch. The unit provides you with a simple, cost-effective solution for Ethernet switching between end-nodes operating at either 10 or 100 Mbps. Figure 1 and Figure 2 show the front and back panel...

14 Figure 2 Back Panel Key Features The AT-FS708LE Ethernet Switch has the following features: ❑ LEDs for unit and port status ❑ 8 Auto-Negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ Auto MDI/MDI-X on all ports ❑ IEEE 802.3 and IEEE 802.3u compliant ❑ Store and forward switching ...

AT-FS708LE Installation Guide 15 Status LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description PWR Green Indicates the switch is receiving power. 100M Green OFF Indicates the port is operating at 100 Mbps. Indicates the port is operating at 10 Mbps. ...

18 The AT-FS708LE supports TX Flow Control only. This means a PAUSE packet will be transmitted to the end-node connection if it receives data faster than it can switch the packets. The AT-FS708LE does not support RX Flow Control, however, and it will not respond to PAUSE packets sent to it by an end...

AT-FS708LE Installation Guide 19 port on the switch and the end-node are operating at the same speed and that they are communicating at the highest possible common speed of the devices. Duplex Mode Duplex mode refers to the way an end-node sends and receives data on the network. An end-node can oper...

22 Network Topologies The AT-FS708LE switch can be used in a variety of network topologies, such as a standalone or cascade. Both topologies are described below. Standalone Topology Figure 3 illustrates the standalone topology where each end-node is directly connected directly to a 10/100Base-TX por...

AT-FS708LE Installation Guide 23 Cascade Topology Figure 4 illustrates the cascade topology where Port 1 on the AT-FS708LE switch is connected to Port 8 on the AT-FS716E switch. Since Port 1 is wired as auto MDI/MDI-X, a crossover or straight-through Category 5 or better twisted pair cable can be us...

24 Note Cascading switches, as shown in Figure 4, can result in data loss between switches if the data rate exceeds 100 Mbps. Symptoms may include inability of certain workstations to “Log-On” to a server or unusually slow data transfer rates between workstations or servers. Planning the Installatio...

AT-FS708LE Installation Guide 25 Selecting a Site Be sure to observe the following site requirements: ❑ Make sure you are placing the device in a dust-free and moisture-free environment. ❑ Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the fro...

26 Table 2 10Base-T/100Base-TX Twisted Pair Port Cabling Specifications Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the device. Warning Power cord is used as a disconnection device: To de-energize equipment, disconnect the power cord. 5 Opera...

28 Installing the Unit on a Desktop To wall-mount the switch on a wall, refer to “Installing the Unit on a Wall” on page 29. To install the switch on the desktop, perform the following procedure. 1. Attach the four self-adhesive rubber feet to the bottom of the device, positioning them in the indent...

AT-FS708LE Installation Guide 29 6. Power ON the end-nodes connected to the switch. 7. Check that the LNK/ACT LED for each port on the switch is green. If a LED is OFF, refer to “Troubleshooting” on page 31. The AT-FS708LE switch is now ready for use. Installing the Unit on a Wall For wall-mount ins...

AT-FS708LE Installation Guide 31 Warranty Registration When you finish installing the product, you should register you product by completing the enclosed warranty card and sending it in. Troubleshooting The following procedure should be perform after you have initially installed the unit to check to...

32 ❑ Verify that the node connected to the port on the switch is powered ON. If the node is OFF, power the unit ON. ❑ Verify that the distance between the switch and the connected network device is no greater than 100 meters (328 feet). ❑ Check to be sure that you are using the correct type of cable...

AT-FS708LE Installation Guide 33 Technical Specifications Standards Compatibility: IEEE 802.3, IEEE802.3u Power Supply: Input: 120V @ 1A Connectors: RJ-45 Address Table: Up to 4,000 entries Queue Buffer: 256K bytes Physical Dimensions: W x D x H 14.6 x 8.2 x 2.6 cm (5.8 x 3.3 x 1.0 in) Weight: 350 g...