Allied Telesis 86253-07 - Manuals

Allied Telesis 86253-07 – Manual in PDF format online.

Manuals:

Manual

Manual Allied Telesis 86253-07

Summary

Page 3 - Query; SMTP third; Full

Patch 86253-07 For Rapier Series Switches 3 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E A memory leak occurred if DNS relay was configured, and the device kept receiving DNS Query packets. This issue has been resolved. PIM6 could not send unicast bootstrap messages to a new neighbou...

Page 4 - Patch Release Note; name; When the DHCP server rejected a

4 Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E A filter entry was lost when the SET SWITCH L3FILTER ENTRY command did not succeed. This issue has been resolved. Link-local addresses can only be unicast addresses. If a link-local address was added as an anycast add...

Page 8 - IGMP Snooping is active, L3FILT is activated; NAT is

8 Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E When two devices are BSR candidates, and have the same preference set with the SET PIM BSRCANDIDATE PREFERENCE command, the device with the higher IP address was not elected as the candidate. This issue has been resol...

Page 9 - ifAdminStatus

Patch 86253-07 For Rapier Series Switches 9 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E The warning given when a QoS policy is active on a port operating at reduced speed has been changed to reflect the problem more accurately. The old message was: Warning (2087343): Port <Port n...

Page 11 - ADD IGMPSNOOPING ROUTERADDRESS; Syntax; Description; ipaddr; Syntax; SET IGMPSNOOPING ROUTERMODE=; Description; This command sets the mode of operation for IGMP Snooping.; DELETE IGMPSNOOPING ROUTERADDRESS; Syntax; where

Patch 86253-07 For Rapier Series Switches DELETE IGMPSNOOPING ROUTERADDRESS 11 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E ADD IGMPSNOOPING ROUTERADDRESS Syntax ADD IGMPSNOOPING ROUTERADDRESS= ipaddr [, ... ] Description where: • ipaddr is a reserved IP multicast address in dotted d...

Page 12 - SHOW IGMPSNOOPING ROUTERADDRESS; Figure 1: Example output for SHOW IGMPSNOOPING ROUTERADDRESS; IGMP Snooping Router Address; Level: 2

12 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E Description This command deletes reserved IP multicast addresses from the list of router multicast addresses. The IP address specified must be within the range 224.0.0.1 to 224.0.0.255...

Page 15 - Base Software Release File; Level: 4

Patch 86253-07 For Rapier Series Switches SHOW IGMPSNOOPING ROUTERADDRESS 15 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E When static port security was enabled with the RELEARN parameter in the SET SWITCH PORT command, and a switch port was reset or unplugged, the MAC entries were re...

Page 16 - DISABLE IP; Enable and Disable ICMP Messages

16 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E When using MVR on a Rapier 48 or Rapier 48 i , multicast packets were not forwarded correctly between ports 1-24 and 25-48. This issue has been resolved. The switch filter was not oper...

Page 17 - SET ENCO DHPADDING=OFF; reachable

Patch 86253-07 For Rapier Series Switches SHOW IGMPSNOOPING ROUTERADDRESS 17 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E For example, to turn off the Diffie Hellman padding, use the command: SET ENCO DHPADDING=OFF Also, the output of the SHOW ENCO command now contains a new line sho...

Page 26 - invalid; error message. Also, when the TRACE command

26 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E When adding a port to a VLAN, any STP ports that had been disabled in the default STP were re-enabled. This issue has been resolved. When the DELETE DHCP RANGE command was executed, DH...

Page 28 - Internet Control Message Protocol; Network Unreachabl; target is located on the same; Commands; DISABLE IP ICMPREPLY

28 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E Enable and Disable ICMP Messages The Internet Control Message Protocol (ICMP) allows routers to send error and control messages to other routers or hosts. It provides the communication...

Page 29 - DISABLE IP ICMPREPLY=ALL; ENABLE IP ICMPREPLY; ENABLE IP; ENABLE IP ICMPREPLY=ALL; SHOW IP ICMPREPLY; SHOW IP ICMP REPLY MESSAGES

Patch 86253-07 For Rapier Series Switches SHOW IGMPSNOOPING ROUTERADDRESS 29 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E If ALL is specified, all configurable ICMP message replies are disabled. If NETUNREACH is specified, all network unreachable message replies are disabled (RFC792 ...

Page 30 - MLD Snooping; MLD snooping is enabled by default. To disable it, use the command:; DISABLE MLDSNOOPING; To display debugging information, use the command:; ENABLE MLDSNOOPING DEBUG; To display information about MLD snooping, use the command:; SHOW MLDSNOOPING COUNTER; IPv6 Multicasting; ICMP Reply Messages

30 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E MLD Snooping Multicast Listener Discovery (MLD) snooping enables the switch to forward IPv6 multicast traffic intelligently, instead of flooding it out all ports in the VLAN. With MLD ...

Page 31 - IGMP Snooping All-Group Entry; IGMP snooping; This enhancement modifies one command:

Patch 86253-07 For Rapier Series Switches SHOW IGMPSNOOPING ROUTERADDRESS 31 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E IGMP Snooping All-Group Entry Because IGMP is an IP-based protocol, multicast group membership for VLAN aware devices is on a per-VLAN basis. If at least one port...

Page 32 - Modified Command; interface; This enhancement includes the line “; Disabled All-groups ports; ” on the output; Examples; To show information about IGMP, use the command:; SHOW IP IGMP; See Also; IGMP Protocol

32 SHOW IP IGMP Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E Modified Command SHOW IP IGMP Syntax SHOW IP IGMP [COUNTER] [INTERFACE= interface ] Description This command displays information about IGMP, and multicast group membership for each IP interface. This en...

Page 33 - DISABLE IP IGMP ALLGROUP; New Commands; ENABLE IP IGMP ALLGROUP

Patch 86253-07 For Rapier Series Switches DISABLE IP IGMP ALLGROUP 33 Patch 86253-07 for Software Release 2.5.3C613-10382-00 REV E New Commands This enhancement request introduces two new commands from enabling/disabling all-group entries on switch ports. ENABLE IP IGMP ALLGROUP Syntax ENABLE IP IGM...

Page 34 - Availability; licence or password is not required to use a patch.

34 DISABLE IP IGMP ALLGROUP Patch Release Note Patch 86253-07 for Software Release 2.5.3 C613-10382-00 REV E Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html . A licence or password is not req...