Allied Telesis 86251-08 - Manuals

Allied Telesis 86251-08 – Manual in PDF format online.

Manuals:

Manual

Manual Allied Telesis 86251-08

Summary

Page 8 - Level: 2

8 Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I When the device received a version 1 Query packet, it become a non-querier on that interface, even if it should have remained as the querier. This issue has been resolved. When the TYPE parameter was specified for the...

Page 47 - Availability; ICMP Router Discovery Advertisements; Support for Router; Benefits

Patch 86251-08 For Rapier Series Switches 47 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I The ADD IPV6 HOST command was not accepting the INTERFACE parameter when adding a host with a link-local address. This issue has been resolved. TCP did not send a TCP Reset message under some ci...

Page 49 - Preference Level; Lifetime; Configuration

Patch 86251-08 For Rapier Series Switches 49 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I routers on the same link. By default the minimum is 450 seconds (7.5 minutes), and the maximum is 600 seconds (10 minutes). Preference Level The preference level is the preference of the adverti...

Page 50 - Commands

50 Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I this value. If it should never be used as a default router, set it to NOTDEFAULT. ADD IP INTERFACE= interface IPADDRESS={ ipadd |DHCP} PREFERENCELEVEL={-2147483648..2147483647|NOTDEFAULT} [ other-ip-parameters ] SET ...

Page 51 - DISABLE IP ADVERTISE; ADD IP ADVERTISE INTERFACE

Patch 86251-08 For Rapier Series Switches ADD IP ADVERTISE INTERFACE 51 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I ENABLE IP ADVERTISE Syntax ENABLE IP ADVERTISE Description This command globally enables ICMP Router Discovery advertisements on the router. However the device will no...

Page 52 - See Also; DELETE IP ADVERTISE INTERFACE; Syntax; Description

52 DELETE IP ADVERTISE INTERFACE Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I Description This command adds ICMP Router Discovery advertising to a single physical IP interface. The interface will only send router advertisements if it has been globally enabled with...

Page 53 - Example; SET IP ADVERTISE INTERFACE

Patch 86251-08 For Rapier Series Switches SET IP ADVERTISE INTERFACE 53 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I Example To delete Router Discovery from vlan1, use the command: DELETE IP ADVERTISE INTERFACE=vlan1 See Also DISABLE IP ADVERTISEENABLE IP ADVERTISEADD IP DISCOVERY IN...

Page 56 - Adopting the VRRP IP Address; Risks

56 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I Adopting the VRRP IP Address Benefits The VRRP master router can adopt the IP address of the virtual router (VR), and respond to the following packets destined for the VR IP address, even if it does...

Page 57 - MLD Snooping

Patch 86251-08 For Rapier Series Switches SHOW IP ADVERTISE 57 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I The ADOPTVRIP parameter specifies that when the switch is acting as the VRRP master it should respond to requests directed at any IP address that it is backing up, even if it d...

Page 58 - Ping Polling of Device Reachability

58 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I Note that IPv6 multicast packets will flood the VLAN when MLD snooping is disabled. To enable MLD snooping, use the command: ENABLE MLDSNOOPING To display debugging information, use the command: ENA...

Page 59 - DOWN: device unreachable

Patch 86251-08 For Rapier Series Switches SHOW IP ADVERTISE 59 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I To create a polling instance, use the command: ADD PING POLL= poll-id IPADDRESS={ ipadd | ipv6add [% interface ]} [CRITICALINTERVAL=1..65535] [DESCRIPTION= poll-description ] [...

Page 60 - Enable and Disable ICMP Messages; Network Unreachabl

60 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I After you have configured the ping polling instance, specify a script or scripts to run when the device becomes unreachable, using the command: CREATE TRIGGER= trigger-id MODULE=PING EVENT=DEVICEDOW...

Page 61 - DISABLE IP ICMPREPLY; ENABLE IP ICMPREPLY

Patch 86251-08 For Rapier Series Switches SHOW IP ADVERTISE 61 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I Commands This enhancement introduces three new commands: ■ DISABLE IP ICMPREPLY ■ ENABLE IP ICMPREPLY ■ SHOW IP ICMPREPLY DISABLE IP ICMPREPLY Syntax DISABLE IP ICMPREPLY[={ALL...

Page 62 - Static IGMP

62 SHOW IP ADVERTISE Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I SHOW IP ICMPREPLY Syntax SHOW IP ICMPREPLY Description This command display the status of configurable ICMP messages (Figure Figure 4: Example output from the SHOW IP ICMPREPLY command: Static IGMP ...

Page 63 - Configuration Example

Patch 86251-08 For Rapier Series Switches SHOW IP ADVERTISE 63 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I Figure 6: Forwarding multicast data over a specified interface and port. Configuration Example The following configuration example illustrates the steps required to create a st...

Page 64 - Modified Command; SHOW IP IGMP

64 SHOW IP IGMP Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I Commands This enhancement modifies one command: ■ SHOW IP IGMPThis command now includes a DESTINATION parameter. Only the modified parts of the command text are shown below. and has seven new commands: ■...

Page 66 - New Commands; ADD IP IGMP DESTINATION

66 ADD IP IGMP DESTINATION Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I New Commands ADD IP IGMP DESTINATION Syntax ADD IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address. ■ i...

Page 67 - CREATE IP IGMP DESTINATION

Patch 86251-08 For Rapier Series Switches CREATE IP IGMP DESTINATION 67 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I CREATE IP IGMP DESTINATION Syntax CREATE IP IGMP DESTINATION= ipaddress INTERFACE= interface [PORT={ALL| port-list }] where: ■ ipaddress is an existing IGMP group dest...

Page 68 - DELETE IP IGMP DESTINATION; DESTROY IP IGMP DESTINATION

68 DELETE IP IGMP DESTINATION Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I DELETE IP IGMP DESTINATION Syntax DELETE IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address. ■ inter...

Page 69 - DISABLE IP IGMP DEBUG; ENABLE IP IGMP DEBUG

Patch 86251-08 For Rapier Series Switches ENABLE IP IGMP DEBUG 69 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I DISABLE IP IGMP DEBUG Syntax DISABLE IP IGMP DEBUG Description This command disables all IGMP debugging messages and resets the DESTINATION and SOURCEIPADDRESS parameters se...

Page 70 - Examples; Checking the Port Map on Rapier16f

70 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I SHOW IP IGMP DEBUG Syntax SHOW IP IGMP DEBUG Description This command shows the IGMP debugging options that have been set. Figure 8: Example output from SHOW IP IGMP DEBUG. Examples To display IGMP...

Page 71 - How to check that the port map is correct; A correct port map

Patch 86251-08 For Rapier Series Switches SHOW IP IGMP DEBUG 71 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I ■ software release 86s-251 and patch 86251-04 are loaded, but the patch was corrupted after a restart or reboot. The Rapier16f i requires the 86251-04 patch to operate correct...

Page 72 - An incorrect port map; How to restore the correct port map

72 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I Although the ifIndex and Interface numbers do not match, this is the correct port map . You do not need to take any more action if you have the correct port map. An incorrect port map If the 86251-...

Page 73 - PPPoE Client on VLAN Interfaces

Patch 86251-08 For Rapier Series Switches SHOW IP IGMP DEBUG 73 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I Figure 3: Router startup messages Enter [Y] when the Force EPROM download (Y)? option appears. 11. Load the 86251-04.paz patch file, and set it as the preferred patch. To load...

Page 74 - ADD PPP

74 ADD PPP Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I ADD PPP Syntax ADD PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 to 511. ■ physical-interface is: • SYN n • DS3 n • ISDN- callname •...

Page 75 - CREATE PPP

Patch 86251-08 For Rapier Series Switches CREATE PPP 75 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I CREATE PPP Syntax CREATE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 to 511. ■ physical-interface is: • S...

Page 76 - DELETE PPP; SET PPP

76 DELETE PPP Patch Release Note Patch 86251-08 for Software Release 2.5.1 C613-10356-00 REV I DELETE PPP Syntax DELETE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 to 511. ■ physical-interface is: • SYN n • DS3 n • ISDN- c...

Page 77 - SHOW PPP

Patch 86251-08 For Rapier Series Switches SHOW PPP 77 Patch 86251-08 for Software Release 2.5.1C613-10356-00 REV I Description This command is used to change the configuration parameters of a PPP interface running over: ■ a synchronous port ■ a DS3 port ■ an ISDN call ■ an ACC call ■ a MIOX circuit ...