Allied Telesis 86251-05 - Manuals

Allied Telesis 86251-05 – Manual in PDF format online.

Manuals:

Manual

Manual Allied Telesis 86251-05

Summary

Page 2 - This issue will seldom appear, and will cause minor inconvenience.

2 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Features in 86251-05 Patch 86251-05 includes all issue...

Page 4 - Reclaim

4 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F IP routes deleted from the route cache occasionally caused a fatal error. This issue has been resolved. The reconnection to the stream printing TCP port failed after a single successful connection was made. This issue...

Page 8 - Static IGMP

8 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F The ENTRY parameter from the ADD IP FILTER command was not included in the output of the SHOW CONFIG DYNAMIC command. This issue has been resolved. An enhancement allows for the creation of static IGMP group membershi...

Page 9 - Patch file details are listed in Table 2:

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers 9 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Features in 86251-04 Patch file details are listed in Table 2: Patch 86251-04 includes all issues resolved and enhancements released in previous patches for So...

Page 10 - OSPF and RIP

10 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F OSPF and RIP Hello packets were being sent out all trunked ports. Now these Hello packets are only sent out the master port of the trunked group. A device could not Telnet to a device outside its own subnet. This iss...

Page 12 - The SHOW CONFIG=ACC command was not showing the

12 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F An additional check has been added to validate the MASK specified in an ADD IP ROUTE command. The check tests that the mask is contiguous. The SHOW CONFIG=ACC command was not showing the rscript file. This issue has ...

Page 14 - The following issues with DHCP have been resolved:

14 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F The following issues with DHCP have been resolved: • DHCP assigned an incorrect IP address to clients shifting from a relayed to a non-relayed range. Gateway checks have been added to resolve this issue. • DHCP clien...

Page 16 - exclude

16 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F An assert storm sometimes occurred with PIM-DM. This issue has been resolved. The firewall doubled the IPSPOOF event timeout from 2 minutes to 4 minutes. This issue has been resolved. MLD did not respond correctly wh...

Page 18 - Series Switches with multiple STPs on the receiving port.

18 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F Debugging for DHCP and Q931 was not being disabled when a Telnet session finished. This issue has been resolved. A log message is now created when a user is forced to logout from an asynchronous port when another use...

Page 20 - When a Rapier

20 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F When a Rapier i Series Switch was using layer 3 multicast protocols, IGMP group members on the upstream interface for the multicast stream would always be forwarded to, even if they left the group. This issue has bee...

Page 21 - Level: 2

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers 21 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Features in 86251-03 Patch file details are listed in Table 3: Patch 86251-03 includes all issues resolved and enhancements released in previous patches for S...

Page 22 - UP

22 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F When the TX cable was unplugged from a fibre port the operating status was incorrectly reported as UP . This issue has been resolved. When replying to a DHCP REQUEST that had passed through a DHCP relay, the broadcas...

Page 24 - TCP did not send a; Availability; licence or password is not required to use a patch.; This section describes an enhancement to the; Network affecting: No

24 Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F TCP did not send a TCP Reset message under some circumstances, for example when the Telnet server was disabled. This issue has been resolved. If ingress filtering was supported within trunk groups, ports with ingress...

Page 25 - Configuration Example; has already been configured as; This must be done before the static IGMP association is created.

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers 25 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Figure 2: Forwarding multicast data over a specified interface and port. Configuration Example The following configuration example illustrates the steps requi...

Page 26 - Commands; Modified Command; SHOW IP IGMP; Syntax; interface; Description

26 SHOW IP IGMP Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F Commands This enhancement modifies one command: ■ SHOW IP IGMPThis command now includes a DESTINATION parameter. Only the modified parts of the command text are shown below. and has seven new commands: ■...

Page 27 - See Also; SHOW IP IGMP DEBUG

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers SHOW IP IGMP 27 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Figure 3: Example output from the SHOW IP IGMP DESTINATION command showing Static Groups. See Also SHOW IP IGMP DEBUG IGMP Protocol -------------...

Page 28 - New Commands; ADD IP IGMP DESTINATION; ADD IP IGMP DESTINATION=

28 ADD IP IGMP DESTINATION Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F New Commands ADD IP IGMP DESTINATION Syntax ADD IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address. ■ i...

Page 29 - CREATE IP IGMP DESTINATION; CREATE IP IGMP DESTINATION=; To forward multicast data to 224.1.2.3 out ports 1 to 4 using

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching RoutersCREATE IP IGMP DESTINATION Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F CREATE IP IGMP DESTINATION Syntax CREATE IP IGMP DESTINATION= ipaddress INTERFACE= interface [PORT={ALL| port-list }] where: ■ ipaddres...

Page 30 - DELETE IP IGMP DESTINATION; DELETE IP IGMP DESTINATION=; DESTROY IP IGMP DESTINATION; DESTROY IP IGMP DESTINATION=

30 DELETE IP IGMP DESTINATION Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F DELETE IP IGMP DESTINATION Syntax DELETE IP IGMP DESTINATION= ipaddress INTERFACE= interface PORT={ALL| port-list } where: ■ ipaddress is an existing IGMP group destination address. ■ inter...

Page 31 - DISABLE IP IGMP DEBUG; ENABLE IP IGMP DEBUG

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching RoutersENABLE IP IGMP DEBUG 31 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F DISABLE IP IGMP DEBUG Syntax DISABLE IP IGMP DEBUG Description This command disables all IGMP debugging messages and resets the DESTINATIO...

Page 32 - Examples; Checking the Port Map on Rapier16f; This information is for Rapier16fi switches only.

32 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F SHOW IP IGMP DEBUG Syntax SHOW IP IGMP DEBUG Description This command shows the IGMP debugging options that have been set. Figure 4: Example output from SHOW IP IGMP DEBUG. Examples To display IGMP...

Page 33 - How to check that the port map is correct; ifIndex; A correct port map

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching RoutersSHOW IP IGMP DEBUG 33 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F ■ software release 86s-251 and patch 86251-04 are loaded, but the patch was corrupted after a restart or reboot. The Rapier16f i requires th...

Page 34 - An incorrect port map; How to restore the correct port map

34 SHOW IP IGMP DEBUG Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F Although the ifIndex and Interface numbers do not match, this is the correct port map . You do not need to take any more action if you have the correct port map. An incorrect port map If the 86251-...

Page 35 - PPPoE Client on VLAN Interfaces; servicename

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching RoutersSHOW IP IGMP DEBUG 35 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Figure 3: Router startup messages Enter [Y] when the Force EPROM download (Y)? option appears. 6. Load the 86251-04.paz patch file, and set ...

Page 36 - ADD PPP; callname

36 ADD PPP Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F ADD PPP Syntax ADD PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 to 511. ■ physical-interface is: • SYN n • DS3 n • ISDN- callname •...

Page 37 - CREATE PPP

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers CREATE PPP 37 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F CREATE PPP Syntax CREATE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 ...

Page 38 - DELETE PPP; SET PPP

38 DELETE PPP Patch Release Note Patch 86251-05 for Software Release 2.5.1 C613-10356-00 REV F DELETE PPP Syntax DELETE PPP= ppp-interface OVER= physical-interface [other parameters] where: ■ ppp-interface is the PPP interface number, from 0 to 511. ■ physical-interface is: • SYN n • DS3 n • ISDN- c...

Page 39 - SHOW PPP

Patch 86251-05 For Rapier Switches and AR800 Series Modular Switching Routers SHOW PPP 39 Patch 86251-05 for Software Release 2.5.1C613-10356-00 REV F Description This command is used to change the configuration parameters of a PPP interface running over: ■ a synchronous port ■ a DS3 port ■ an ISDN ...