Allied Telesis 48W - Manuals

Installation and Safety Guide 5 Package Contents These items are included with each Rapier 48w switch. Contact your authorised distributor or reseller if any items are damaged or missing. AC model package contents ■ one serial cable for connecting the switch to a terminal or PC ■ one AC power cord ■...

Rapier 48w Switch 6 Selecting a Site Before you install the switch, review the following considerations about its location. ■ The Rapier 48w switch requires an ambient temperature from 0º C to 50ºC (32º F to 122º F). ■ There should be adequate front-to-back airflow around the switch and its vents. ■...

Installation and Safety Guide 7 Installing the Switch You can install the switch on a level surface, such as a desktop or bench, in a standard 19-inch rack, or in a 23-inch rack. The ports on the switch must not be metallically connected to interfaces that connect to Outside Plant or its wiring (NEB...

Rapier 48w Switch 8 Rack-mount the switch 1. Ensure the rack has sufficient space for the switch and its cables. For the switch’s requirements, see “Selecting a Site” on page 6 . 2. Install cage nuts, if required, so they are ready for the rack-mount screws in the following steps. The Rapier 48w can...

Installation and Safety Guide 9 Install the air filters (NEBS installation only) Rapier 48w DC switches are shipped with air filters that you must install in each of the fan units for Network Equipment Building System (NEBS) compliance. To install an air filter: 1. Using a flat screwdriver, undo the...

Rapier 48w Switch 10 Applying Power to the Switch The specific power supply requirements for the Rapier 48w are clearly displayed on the rear of the switch. If the supply is outside the accepted range for the switch, the switch may not operate or damage to the switch may result. Warning All versions...

Installation and Safety Guide 11 Rapier 48w DC switch Follow these instructions when connecting the DC switch variant. Read “Safety” on page 23 of this document before connecting a DC power supply. Warning Only trained and qualified personnel should connect a DC power supply. For centralised DC powe...

Rapier 48w Switch 12 Connect the switch to ground The protective earth connection should be connected before proceeding with the following power connections. The primary ground for the equipment is a two stud grounding block (bearing the grounding symbol) located on the left rear of the chassis, adj...

Rapier 48w Switch 14 Connecting Data Cables to the Switch Once initial configuration is complete, connect the switch to the network. Warning The Ethernet, DS3, T1, and management/asyn ports of the equipment are suitable for connection to intra-building or unexposed wiring or cabling only. These port...

Installation and Safety Guide 15 The SFP transceiver must be inserted the right way in the slot: ■ To install an SFP in port 49 (upper), the release lever hinge must be at the bottom. ■ To install an SFP in port 50 (lower), the release lever hinge must be at the top. To insert an SFP transceiver, sl...

Rapier 48w Switch 16 Configuring the Switch The Rapier 48w switch can be configured with the Command Line Interface (CLI). Before configuring the switch, you must make some basic connections explained in the following procedure. Before starting the procedure, ensure that the switch is installed and ...

Rapier 48w Switch 18 Checking LEDs The following tables describe how the switch and expansion modules report faults and operational activities. Expansion modules are optional and must be purchased separately. Contact your authorised Allied Telesis distributer or reseller, or visit www.alliedtelesis....

Rapier 48w Switch 20 Documentation Set The complete document set for Rapier Series switches includes the following: ■ This Installation and Safety Guide for the Rapier 48w switch ■ The Rapier 48w Switch Removable Fan Installation Guide , which describes how to install AT-FAN04 fan-only modules (FOMs...

Installation and Safety Guide 21 AC Model Standards The Rapier 48w-B AC switch meets the following standards: Category Approval Agency and Requirement Electrical Safety UL60950-1 CAN/CSA-C22.2 No. 60950-1-03 EN60950-1 AS/NZS 60950.1 EN 60825-1 21 CFR 1040 Electromagnetic Compliance FCC CFR47 Part 15...

Rapier 48w Switch 22 DC Model Standards The DC models of the Rapier 48w and 48w-B switches meet the following standards: Category Approval Agency and Requirement Electrical Safety UL60950-1 CAN/CSA-C22.2 No. 60950-1-03 21 CFR 1040EN60950-1AS/NZS 60950.1EN60825-1 Electromagnetic Compliance FCC CFR47 ...

Installation and Safety Guide 23 Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Class 1 Laser product. WARNING: Do not stare into the laser beam. CAUTION: Use of controls or adjustments of...

Rapier 48w Switch 24 ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. WARNING: For centralized DC power connection, install only in a restricted access area. WARNING: Only trained and qualified personnel are allowed to install or replace this equipment. WARNING:...

Rapier 48w Switch 26 Nehmen Sie STETS zuerst die Verkabelung der LAN-Einrichtung vor, bevor Sie die Kabel an den Leistungsschalter anschließen. Arbeiten Sie nie mit SPANNUNGSFÜHRENDEN Kabeln, um Körperverletzungen durch Stromschlag zu vermeiden. Achten Sie stets darauf, daß sich der Leistungsschalte...

Rapier 48w Switch 28 Advarsel: “Fare” Se omhyggeligt efter om der stikker blanke kobbertråde ud fra klemmeforbindelserne. Ved korrekt montering er det ikke tilfældet. Enhver afisoleret leder kan lede farlig strømstyrke til personer, som kommer til at røre ved dem. Bemærk: Dette udstyr kan køre både ...

Rapier 48w Switch 30 Sécurité MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. ATTENTION Producit laser di classe 1. ATTENTION Ne pas fixer le faisceau des yeux. INFORMATION ...

Rapier 48w Switch 32 Turvallisuus VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. VAROITUS Luokan 1 Lasertuote. VAROITUS Älä katso säteeseen. SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA VAR...

Installation and Safety Guide 33 Varoitus: KESKITETTY TASAVIRTAKYTKENTÄ ASENNETTAVA AINOASTAAN TILAAN, JOHON ON RAJOITETTU PÄÄSY. Varoitus: TÄMÄN LAITTEEN SAA ASENTAA TAI VAIHTAA AINOASTAAN KOULUTETTU JA AMMATTITAITOINEN HENKILÖKUNTA. Varoitus: Tämän LAN-laitteen kanssa käytettävän kaapelin syöttöpä...

Installation and Safety Guide 35 cavi SOTTO TENSIONE. Prima di collegare il cavo all’interruttore di sicurezza, accertarsi sempre che quest’ultimo sia disinserito. Avvertenza: Per evitare i possibili pericoli associati all’esposizione dei fili sulla morsettiera dopo l’installazione, non rimuovere l’...

Installation and Safety Guide 37 Segurança AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. AVISO Produto laser de classe 1 AVISO Não olhe fixamente para o raio. AVISOS SOBRE CARACTERÍSTI...

Installation and Safety Guide 39 Seguridad ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. ¡ADVERTENCIA! Producto láser Clase 1. ¡ADVERTENCIA! No mirat fijamente e...

Installation and Safety Guide 41 Säkerhet VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. VARNING! Laserprodukt av klass 1. VARNING! Laserstrålning när enheten är öppen. TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITE...

Rapier 48w Switch 42 Varning: INSTALLATION OCH UTBYTE AV DENNA UTRUSTNING FÅR ENDAST UTFÖRAS AV AUKTORISERAD ELINSTALLATÖR. Varning: Av säkerhetsskäl skall en 15 A automatsäkring anslutas till försörjningsänden på kabeln som används till denna LAN-utrustning. Ledningar skall ALLTID anslutas till LAN...

Installation and Safety Guide 43 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. 5. Remove the telephone cord from the unit prior to making changes to the ex...

Rapier 48w Switch 44 US Federal Communications Commission (FCC) This equipment complies with Part 68 of the Federal Communications Commission (FCC) rules for the United States. A label is located on the underside of the base unit containing the FCC registration number. You must, upon request, provid...