Alliance UW100TV- Manuals

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information F8138601 4 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked. Safety Decals Safety decals appear at cruci...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 F8138601 Introduction Model Identification Information in this manual is applicable to these models: UW35TVUW60TVUW80TV UW100TVUW125TVUW150TV

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction F8138601 6 This manual is designed as a guide to the installation of the Pocket Hardmount washer-extractor. NOTE: All information, illustrations, and specifications contained in this manual are based on the latest produ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 7 F8138601 Figure 2 Model Number Familiarization Guide Sample Model Number: UW60TVQU10001 UW Model Number Prefix 60 Washer-Extractor Capacity (60 pounds dry weight of laundry) T Type of Electrical Control T = UniLinc Co...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8138601 8 Specifications and Dimensions . Specifications 35 60 80 100 125 150 Overall Dimensions Overall width, in (mm) 32.5 (826) 36.625 (930) 41.5 (1054) 41.5 (1054) 48 (1219) 50.25 (1277) Overall height, in (mm) 55.5 (1410) 64.5...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 10 Machine Dimensions Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 6 inches (15.24 cm) at the sides for maintenance, inspection, and adjustment. Allow at least 6 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 13 F8138601 Machine Foundation Requirements A 6 inch (153 mm) (for 35 and 60 2-speed, L-speed and M-speed models) or a 12 inch (305 mm) (for all other models) thickness of 3500 psi reinforced concrete f...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 14 Concrete Foundation Pad Installation A concrete foundation and pad may be constructed to elevate the machines. Care must be exercised in the design of the foundation pad due to the force exe...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 16 Floor Load Data Static and dynamic loads on the floor or foundation are shown in Table 2 . UWTV Pocket Hardmount Floor Load Data Specifications Design Series 35 60 80 100 125 150 Static floo...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 17 F8138601 Mounting Bolt Installation Requirements Approved Foundations Only NOTE: If installing expansion bolts into an elevated concrete foundation pad, the concrete foundation pad should extend a mi...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 18 Machine Mounting and Grouting After the concrete has cured, proceed as follows: 1. Place the washer-extractor adjacent to the foundation. Do not attempt to move the machine by pushing on the...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 19 F8138601 NOTE: Mounting holes marked “A” need to be used on all V-Speed Models only. Mounting Bolt Hole Locations Figure 8 PHM630N 26.125 in. (664 mm) 30.125 in. (765 mm) 0.75 in. (19 mm) 2 in. (51 m...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 20 PHM631N Figure 9 1.25 in. (32 mm) 2 in. (51 mm) 44.8125 in. (1138 mm) 39.25 in. (997 mm) 34.5625 in. (878 mm) 34.125 in. (867 mm) 31.625 in. (803 mm) 35.625 in. (905 mm) 2 in. (51 mm) 9 in. ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 21 F8138601 PHM632N Figure 10 0.75 in. (19 mm) 39.625 in. (1008 mm) 0.75 in. (19 mm) 6.75 in. (171 mm) 9 in. (229 mm) 13.625 in. (346 mm) 13.625 in. (346 mm) 43 .75 i n . (1 11 1 mm) 0.75 in. (19 mm) 3 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 24 Grout Placement Figure 13 PHM605N PHM574N PHM575N 150 MODEL 50 in. (1270 mm) 56 in. (1422 mm) PHM574N 35 VARIABLE-SPEED MODEL PHM575N 60 VARIABLE-SPEED MODEL 30.125 in. (765 mm) 17.88 in. (4...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 25 F8138601 Gap Setting for Vibration Switch After the machine has been properly installed, the vibration switch gap must be verified. To locate the vibration switch refer to Figures 14 , 15 and 16 . Fo...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 26 35 Pound Model Figure 14 PHM794N PHM794N ADJUSTMENT BOLT VIBRATION SWITCH

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 27 F8138601 60, 80, 100 and 125 Pound Models Figure 15 PHM795N PHM795N ADJUSTMENT BOLT VIBRATION SWITCH

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 28 150 Pound Model Figure 16 PHM716N PHM716N VIBRATION SWITCH

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 29 F8138601 Drain Connection Requirements A drain system of adequate capacity is essential to washer-extractor performance. The water can empty directly into a sump or floor drain. Figure 17 shows the d...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 30 IMPORTANT: Do not block the overflow vent above the drain line. If water or suds flow from the overflow vent and the machine has been verified to be operating properly with proper water leve...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 31 F8138601 Water Connection Maximum water inlet temperature is 190 ° Fahrenheit (88 ° Celsius). Connections should be supplied by hot and cold water lines of at least the sizes shown in the Water Suppl...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 32 To connect water service to machine with rubber hoses, use the following procedure: 1. Before installing hoses, flush the water system for at least two minutes. 2. Check filters in the washe...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 33 F8138601 Electrical Installation Requirements IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine. Electrical connec...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 34 The washer-extractor should be connected to an individual branch circuit not shared with lighting or other equipment.The connection should be shielded in a liquid-tight or approved flexible ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 35 F8138601 Voltage Designation Non-Electric Heat Machines (Standard) Electric Heat Machines Model Code Volta g e Cycl e Phase Wire Full Lo ad Amp s Br eak er *A WG *mm 2 Full Load Amp s Br eak er *A WG...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 36 Steam Requirements (Steam Heat Option Only) For washer-extractors equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 37 F8138601 Chemical Injection Supply System Undiluted chemical dripping can damage the washer- extractor. Therefore, all chemical supply dispenser pumps should be mounted below the washer’s injection p...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 38 Figure 24 Connecting External Liquid Supplies to the Washer-Extractor 1. Remove knockout from supply dispenser. Refer to Figure 24 . Plugs are assembled inside the tubing ring. 2. Install PG...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 40 External Supplies For proper communication between the washer- extractor and an external chemical supply system, it is important for the signal power to be connected properly. The included w...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 41 F8138601 Chemical injection Using External AC Power Source NOTE: An External AC Power Source is NOT provided by Alliance Laundry Systems. NOTE: Power for external supplies must not be derived from th...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions F8138601 42 External Supply Signals Wash-cycle signals are provided to the external chemical supply equipment and a “wait for the next step” signal can be received from the supply equipment. For example...