Alliance PHM1401C- Manuals

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 4 F8138801 Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are int...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information F8138801 6 Safety Decals Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician. To provide personal safety...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 7 F8138801 Operator Safety To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating the machine, verify that all warning signs are present and legi...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information F8138801 8 • Water Damage . Do not spray the machine with water. Short circuiting and serious damage may result. Repair immediately all seepage due to worn or damaged gaskets, etc. Machine Location • Foundation . ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 9 F8138801 AC Inverter Drive Machines equipped with the AC inverter drive require special attention with regard to the operating environment. • An especially dusty or linty environment will require more frequent c...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 10 F8138801 Introduction Model Identification Information in this manual is applicable to these models: UW35TV UWL060T3M UWN060T3M UWU060T3M UW60TV UWL060T3V UWN060T3V UWU060T3V UW80TV UWL080T3V UWN080T3V UWU080T3V UW100TV UWL100T3V...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 11 F8138801 Nameplate Location The nameplate is located on the back of the machine and is programmed in the UniLinc Control. To access Machine ID through the control: 1. Press and hold , then , then keypads at the same ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13 F8138801 Preliminary Information About the Control The UniLinc control on the washer-extractor is an advanced, graphical, programmable computer that lets the owner control most machine features by interacting with the control. Un...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Preliminary Information F8138801 14 IR Communications Menu The IR Communications Menu displays while the control is communicating with a PDA. The control will jump back to the previous page when the communication is complete. IR Com...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Preliminary Information 15 F8138801 *Manual Programming = Enabled *If manual programming is disabled, programming changes to UniLinc can only be made with an external communication device. Refer to UniLinc PC and PDA Applications Us...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 16 F8138801 UniLinc Identification Operational Keypad The control includes seven keypads. These functions are available to the operator and are intended to control and manage operation of the washer-extractor. Refer to Figure 5 and ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT UniLinc Identification 17 F8138801 Operation Modes General Modes of Operation In each mode of operation, the user may press keypads or communicate with the control to change the displayed menu. Power-up Mode The control enters this ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 18 F8138801 Machine Cycle Definition and Operation There are 41 machine cycles which can be selected and run. Machine cycles can be modified or made “unavailable” by manually editing them in Modify Cycle Menu or by using the PDA to ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation 19 F8138801 To Start a Cycle 1. Press the or keypad to change cycles. 2. Press the keypad to move the cycle in the rightmost menu box to the center, highlighted position. 3. Press the keypad to...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation F8138801 22 Contrast/Backlight Menu Press the keypad from Cycle Menu or Run Menu to enter the Contrast Adjust/Backlight Menu. The Contrast Adjust/Backlight Menu allows the user to adjust contra...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation 23 F8138801 Lubricate Bearings Menu The Lubricate Bearings Menu displays when the machines has run for 200 hours and the bearing is the type that can be lubricated. The Lubricate Bearings Menu ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation F8138801 24 Speed, Temp and Water Level Menu The Speed, Temp, and Level Menu will display the actual RPM, temperature and level, and program values of the temperature and level during run mode....

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation 25 F8138801 Press keypad to abort the cycle. After two minutes without a keypad press the control will abort the cycle and go to the Cycle Aborted Fatal Menu. Cycle Aborted Fatal Menu The Cycle...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Cycle Definition and Operation F8138801 26 Delayed Start Countdown Menu The Delayed Start Countdown Menu will be shown after the delayed start feature has been activated. Press keypad to return to the Cycle Menu. When there ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 27 F8138801 Menu Navigation The UniLinc The front-end control allows the user to control machine operation by pressing keypads to select options on the display menus and by navigating between display menus. The control has four ways...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Menu Navigation F8138801 28 Display Screen Maps Refer to the following charts for maps of all of the display menus. System Menu Map Tree Figure 20 Cycle Menu System Menu Diagnostic Menu Run Menu Service Menu Contrast Adjust Menu Aut...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Menu Navigation 29 F8138801 Run Menu Map Tree Figure 21 Service Menu Map Tree Figure 22 Cycle Menu Run Menu Service Menu System Menu Contrast Adjust Menu Close Door Menu Lube Bearing Menu Delayed Start Menu Auto - Leak Detect Menu ....

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 30 F8138801 Programming UniLinc System Menu The System Menu allows the user to access: cycle programming, diagnostics, laundry management, bearing timer reset/reset bearing timer. Press and hold , then, , then to enter the System Me...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 31 F8138801 Program Menu Program Menu In System Menu, select Program and press . To program cycles, select Modify Cycle and press . To change properties that will affect the machine globally, select Global Setup (i.e., water tempera...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu F8138801 32 NOTE: Refer to Table 2 for a chart of available letters, numbers and symbols. Press the keypad to move highlighted box to Segment Number or press the keypad to move the highlighted box back to the Cycle Numb...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu 33 F8138801 Cycle, Segment and Step Programming Flow Diagram Figure 27 Step Menu Navigation Step Menus are a subgroup of the Modify Cycle Menu and the navigation is very similar to the navigation of the Modify Cycle Men...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu F8138801 34 To set parameters in the step menus, move highlight box to desired step parameter and press , the and keypads to change values. In menus that do not have many values or items to choose from the vertical arro...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu 35 F8138801 The next parameter controls the heater while the machine is actually in the Agitate Step. This parameter is only displayed if a heater is present. There are three choices on heater equipped machines. The cho...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu F8138801 36 The and keypads are used to move the cursor to the different parameters and Internal Supplies 1 through 5. The and keypads are used to move the cursor to the External Supplies 1 through 8. Once a supply has ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu 37 F8138801 Drain Step Menu The Drain Step Menu allows the user to activate or deactivate the drain step and control where the water is drained. The Drain cycle step can be turned on or off by pressing the keypad. If tu...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Menu F8138801 38 Extract Step Menu The Extract Step Menu is used to program the motor speed and time for the Extract Step. The Extract Step can be turned on or off by using the keypad. If turned off, the control will advance...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 39 F8138801 Global Setup Global Setup Menu The Global Setup Menu allows the user to make changes to global properties of the machine. Use the , , , and keypads to navigate the menu. Select a menu item by pressing the keypad. Press t...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup F8138801 40 Press the keypad to return to Global Setup Menu. If no changes were made, press the or keypad to return to Global Setup Menu. The control’s Clock will automatically adjust for leap-year. The control may be p...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup 41 F8138801 Press and keypads to move the highlighted box through the different items in the menu. Once the item is highlighted, press the and keypads to change the values. Press the or keypad to jump to the Save Change...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup F8138801 42 Water Management Menu The Water Management 1 Menu allows the user to set the water reuse and water recirculation options to Yes or No. If water reuse option is turned off, the Reuse Fill Menu will not be dis...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup F8138801 44 Alarms Program Menu The Alarms Program Menu is used to set the fill, drain, and heat alarm times. The and keypads are used to move the highlighted box through the different items in the Alarm Program Menu. O...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup 45 F8138801 Shakeout Menu The Shakeout Menu is used to set the Shakeout time after the Extract Step. The and keypads adjust the time. The time can be set from 0-120 seconds in increments of 20 seconds. Press the or keyp...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup F8138801 46 Water Level Confirmation Menu The Water Level Confirmation Menu is used to confirm that water levels are to be set back to factory defaults. This screen is displayed when the Water Level Only option is selec...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Global Setup 47 F8138801 Audio Confirmation Menu The Audio Confirmation Menu is used to confirm that the audio is to be set back to factory defaults. This screen is displayed when the Audio Only option is selected in the Factory Def...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 48 F8138801 Diagnostic Diagnostic Menu The Diagnostic Menu contains Test, Alarm and Machine ID Menus. The menus contain specific diagnostic information and manufacturing data for the machine. The and keypads position the highlighted...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic 49 F8138801 Test Cycle STEP Test Cycle Step Displayed Description STEP ADVANCE COMMENTS 1 Keypad Test Step FEC and Output Board S/W versions and “Press Each Keypad To Advance” Advance after all keypads depressed. 2 Door a...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic 51 F8138801 Factory Valve Purge Menu The Factory Valve Purge Menu is used to allow the factory to purge all the valves inside the machine after the machine has been manufactured and tested. Press the keypad to activate th...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic F8138801 52 Inputs Outputs Menu When the Inputs Outputs Menu is accessed through the Diagnostic Menu, the user can change outputs. The Close Door Menu will come up if the door is not closed. The user can scroll through th...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic F8138801 54 Water Leak Detection Diagnostic The Water Leak Detection menu is used to display the result of the Water Leak Detection test. Press the keypad to initiate the test. To end the test before it is complete, press...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 56 F8138801 Machine Identification The Machine ID Menu provides several different types of manufacturing and machine information that can be useful to the user, chemical supplier, and technician. The Machine ID Menu cannot be naviga...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Identification F8138801 58 Unbalance Error If the control detects an unbalanced load during a cycle, the control will run the subsequent Spray Rinse Extract and Extract steps but only at a reduced speed and will continue the...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 60 F8138801 Laundry Management The Laundry Management Menu contains three screens displaying the number of operations per cycle, total cycle counts, and total hours run. The Laundry Management 1 of 3 screens displays Total Cycle Cou...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62 F8138801 Maintenance Service Schedule Menu Press from Cycle Menu to enter Service Schedule Menu. The Service Schedule Menu provides a user with a time based service reminder list. The list is broken up into “DAILY”, “WEEKLY”, “MO...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 63 F8138801 Monthly Menu (Service) The Monthly Menu contains all monthly service reminders that need to be performed. Press or to view Monthly Menu (2 of 2). Press the keypad to return to Service Menu. Quarterly Menu (Se...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 64 F8138801 Cycle Charts Cycle No. Cycle Name Cycle Display Name Segment Number & Name Reuse Fill Step Fill Supply A Supply B Agitate Step Cool Dow n Drain Spray Rinse Extract Extract EOS 1 Towels,White, Bleach TowelsWhiteBleach...