Page 3 - © Copyright 2005, Alliance Laundry Systems LLC; Table of Contents; Section 1 – Safety Information
800170 1 © Copyright 2005, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT T...
Page 4 - Section 4 – Grounding
2 800170 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Troubleshooting – EDC Models – Dryer Control ................................................................89 49. Error Code Listing .........................................8950. Cannot Perform Infrared Communication ......
Page 5 - Section 6 – Adjustments
800170 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 123. Dryer Motor and Exhaust Assembly ...........196124. Dryer Front Bulkhead Assembly .................200125. Cylinder Belt ...............................................202126. Dryer Cylinder Assembly .....................
Page 6 - Notes
4 800170 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Notes
Page 7 - Section 1; DANGER; WARNING
800170 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 1 Safety Information Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,” “WARNING” and “DANGER”) followed by specific instructions. These precautions are intended for the...
Page 8 - Section 1 Safety Information; Locating an Authorized Servicer; reconnected to ensure that the washer/dryer is properly grounded.
6 800170 Section 1 Safety Information © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exerci...
Page 9 - Section 2; Customer Service; Nameplate
800170 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 2 Introduction Customer Service If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address ...
Page 10 - Section 2 Introduction; Model Identification
8 800170 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Model Identification Information in this manual is applicable to these models . ModelNumber Coin Drop Installed Coin Drop Ready Card Reader Installed Card Reader Ready Electronic Control Timer Heat HT...
Page 12 - How Your Washer Works
10 800170 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How Your Washer Works Commercial Washer / Dryer WASHER DRYER H159SE3A Coin Drop Motor Control Board (Located inside control cabinet) Pressure Switch (Located inside control cabinet) Mixing Valve Inne...
Page 13 - General; Regular
800170 11 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General This frontload washer provides some of the same principles of operation as the typical topload washers. It senses water level, it dispenses the desired laundry detergent, agitates the clothes...
Page 14 - How Your Dryer Works
12 800170 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How Your Dryer Works The dryer uses heated air to dry loads of laundry. When the motor is started, the exhaust fan pulls fresh air in through louvers at the rear of the dryer and over the heat source...
Page 15 - Section 3; TROUBLESHOOTING COIN DROP; Figure 1
800170 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 16 - Section 3 Troubleshooting
14 800170 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Is machine level? (Machines that aren't level may prevent coins from following through required check stages of drop.) No Yes No Refer to wiring diagram for proper connections. Yes No Yes FLW1687S...
Page 17 - Troubleshooting; Washer; c. Remove the “H3” connector from the motor control board.; TROUBLESHOOTING KNOCKING NOISE; To correct this condition, replace the washer belt. Refer to
800170 15 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 18 - Figure 2
16 800170 Section 3 Troubleshooting (Washer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 2 H006BE3A Out-Of-Balance Switch BallastWeight 1-1/2 Inches Left Front Shock Tape Washer Base Wire Harness (8 inch slack) Plastic Wire Retainer
Page 19 - UNITS; SERVICE PROCEDURE: STUCK BRUSHES; Figure 3; Motor Resistance Values; Table 1
800170 17 Section 3 Troubleshooting (Washer) To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the washer/dryer with any guards/panels ...
Page 20 - Figure 4
18 800170 Section 3 Troubleshooting (Washer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 3 Figure 4 FLW971S Braided wire hangs up on brush holder BRAIDED COPPER WIRE – Must be positioned away from this brush holder. Braided wire should “loop” up and away from bottom of...
Page 21 - SERVICE PROCEDURE: WORN BRUSHES; Figure 5; GOOD BRUSH
800170 19 Section 3 Troubleshooting (Washer) To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the washer/dryer with any guards/panels ...
Page 22 - SERVICE PROCEDURE: CLOGGED BRUSHES; Figure 6; WORN BRUSH
20 800170 Section 3 Troubleshooting (Washer) To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the washer/dryer with any guards/panels ...
Page 23 - EDC Models – Washer Control; EDC ERROR CODE LISTING; This is a fatal error.; dor – Door Open Indicator.; the door is closed, check for wiring or door switches.
800170 21 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 24 - CANNOT PERFORM INFRARED COMMUNICATION
22 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 6. CANNOT PERFORM INFRARED COMMUNICATION Attempt to communicate with electronic control from Micro-wand. Aim Micro-wand closer and try again. Yes Yes No No Is there a...
Page 25 - Section 3 Troubleshooting (EDC Models – Washer Control); COINS IGNORED WHEN ENTERED
800170 23 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ 7. COINS IGNORED WHEN ENTERED Start Coin drop Diagnostic test. Enter several coins Open control panel Check coin drop Make sure control is reset properly and prompti...
Page 26 - ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – WASHER
24 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 8. ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – WASHER Electronic control has no LED or VFD functioning on control board. Plug electronic control washer into electrica...
Page 27 - ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – WASHER
800170 25 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – WASHER BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL...
Page 28 - WASHER WILL NOT START (DOOR AND DOOR LOCK SWITCH) – NO DOOR LOCK ONLY
26 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9. WASHER WILL NOT START (DOOR AND DOOR LOCK SWITCH) – NO DOOR LOCK ONLY Washer will not start (coin inserted) Replace Door Lock Assembly. Replace Door Lock Assembly....
Page 29 - WASHER WILL NOT START (DOOR AND DOOR LOCK SWITCH) – NO DOOR LOCK ONLY
800170 27 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT START (DOOR AND DOOR LOCK SWITCH) – NO DOOR LOCK ONLY BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT ...
Page 31 - WASHER WILL NOT START (ELECTRONIC CONTROL ANALYSIS)
800170 29 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT START (ELECTRONIC CONTROL ANALYSIS) BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YE...
Page 32 - WASHER WILL NOT FILL
30 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11. WASHER WILL NOT FILL Washer will not fill Change inoperative pressure switch. Yes (1) "AC" (2) "AC" (3) "AC" No Still no voltage. Yes No I...
Page 33 - WASHER WILL NOT FILL
800170 31 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT FILL BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/Y...
Page 35 - WASHER OVERFLOWS
800170 33 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER OVERFLOWS BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/YEL R...
Page 36 - WASHER WILL NOT PUMP
34 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13. WASHER WILL NOT PUMP Washer will not pump Correct wiring between pump and electronic control board. Check for a kink or blockage in drain hose. Change inoperative...
Page 37 - WASHER WILL NOT PUMP
800170 35 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT PUMP BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/Y...
Page 39 - “E:SP” ERROR ANALYSIS
800170 37 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ “E:SP” ERROR ANALYSIS BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/...
Page 41 - EDC FRONT LOAD WASHER MODEL
800170 39 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ DOOR LOCKED, MOTOR DOES NOT RUN (E:DF ON DISPLAY) BRN BLU PNK ORG/BLU T A N/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL...
Page 42 - START UP SEQUENCE; e. The “K4” relay is closed on electronic control board.
40 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 16. START UP SEQUENCE a. Insert money and/or card and push the button next to the flashing light. b. Both door closed switches need to be in the closed position, afte...
Page 43 - START UP SEQUENCE
800170 41 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ START UP SEQUENCE BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/YEL ...
Page 44 - SHUT DOWN SEQUENCE; electronic control is opened.
42 800170 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17. SHUT DOWN SEQUENCE a. Towards end of cycle, “:01” is on display. The door lock actuator is powered down and “K2” relay on electronic control is opened. b. The doo...
Page 45 - SHUT DOWN SEQUENCE
800170 43 Section 3 Troubleshooting (EDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ SHUT DOWN SEQUENCE BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/YEL...
Page 47 - MDC Models – Washer Control; ERROR CODE LISTING; Serial communication error.; dor
800170 45 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 48 - Section 3 Troubleshooting (MDC Models – Washer Control); COINS IGNORED WHEN ENTERED; Coins Ignored When Entered.
46 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 19. COINS IGNORED WHEN ENTERED Coins Ignored When Entered. Start Coin Drop Diagnostic Test. Refer to programming manual. Reset control to ready mode. Yes No Is "H...
Page 50 - NO VISIBLE DISPLAY ON CONTROL; Control Has No Visible Display
48 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. NO VISIBLE DISPLAY ON CONTROL Control Has No Visible Display The electronic control has no LED or VFD functioning on the control board. Is the power cord plugged ...
Page 51 - NO VISIBLE DISPLAY ON CONTROL
800170 49 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ NO VISIBLE DISPLAY ON CONTROL 801182 1 2 3
Page 52 - WASHER WILL NOT START – NO DOOR LOCK
50 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21. WASHER WILL NOT START – NO DOOR LOCK Washer Will Not Start. No Door Lock. Washer will not start. Vend satisfied. Is there 120 Volt AC across "H4-5" and &#...
Page 53 - WASHER WILL NOT START – NO DOOR LOCK
800170 51 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT START – NO DOOR LOCK 801182 5 2 3 1 4
Page 54 - WASHER WILL NOT START – CONTROL ANALYSIS; Washer Will Not Start. Control Analysis.
52 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 22. WASHER WILL NOT START – CONTROL ANALYSIS Washer Will Not Start. Control Analysis. Is there 120 Volt AC across "H6-6" to "H6-5" on the control boar...
Page 55 - WASHER WILL NOT START – CONTROL ANALYSIS
800170 53 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ WASHER WILL NOT START – CONTROL ANALYSIS 801182 1
Page 56 - WASHER WILL NOT FILL; Washer Will Not Fill.
54 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 23. WASHER WILL NOT FILL Washer Will Not Fill. Is there 120 Volt AC across the input side of the pressure switch to "FS2" on the motor control board? Correct ...
Page 58 - Washer Overflows
56 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 24. WASHER OVERFLOWS Washer Overflows Is there voltage to the over level terminal on pressure switch to "FS2"? Yes No Replace inoperative pressure switch. Is ...
Page 60 - PUMP DOES NOT OPERATE; Pump Does Not Operate
58 800170 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 25. PUMP DOES NOT OPERATE Pump Does Not Operate Is there voltage across the wht/blk and the white wire going to the motor? Is there voltage across terminals "H6-2...
Page 61 - PUMP DOES NOT OPERATE
800170 59 Section 3 Troubleshooting (MDC Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ PUMP DOES NOT OPERATE 801182 2 1
Page 65 - NetMaster Models – Washer Control; ERROR CODE LISTING
800170 63 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 66 - Section 3 Troubleshooting (NetMaster Models – Washer Control); Display
64 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT EC:06 Invalid Data Code Incorrect machine type. Before downloading, ensure data is for current machine type. EC:09 Corrupted Data Error Communication error. Try...
Page 68 - MICROWAND DOES NOT COMMUNICATE WITH CONTROL; Microwand Does Not Communicate With Control.
66 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 28. MICROWAND DOES NOT COMMUNICATE WITH CONTROL Microwand Does Not Communicate With Control. Attempt to communicate with the electronic control from the Microwa...
Page 69 - COINS IGNORED WHEN ENTERED
800170 67 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ 29. COINS IGNORED WHEN ENTERED Coins Ignored When Entered. Start Coin Drop Diagnostic Test. Refer to programming manual. Reset control to ready mode. Yes No Is...
Page 70 - NO VISIBLE DISPLAY ON CONTROL
68 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 30. NO VISIBLE DISPLAY ON CONTROL Control Has No Visible Display The electronic control has no LED or VFD functioning on the control board. Is the power cord pl...
Page 72 - WASHER WILL NOT START – NO DOOR LOCK
70 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 31. WASHER WILL NOT START – NO DOOR LOCK Washer Will Not Start. No Door Lock. Washer will not start. Vend satisfied. Is there 120 Volt AC across "H4-5" ...
Page 74 - WASHER WILL NOT START – CONTROL ANALYSIS
72 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32. WASHER WILL NOT START – CONTROL ANALYSIS Washer Will Not Start. Control Analysis. Is there 120 Volt AC across "H6-6" to "H6-5" on the contro...
Page 76 - WASHER WILL NOT FILL
74 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33. WASHER WILL NOT FILL Washer Will Not Fill. Is there 120 Volt AC across the input side of the pressure switch to "FS2" on the motor control board? Co...
Page 80 - PUMP DOES NOT OPERATE
78 800170 Section 3 Troubleshooting (NetMaster Models – Washer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 35. PUMP DOES NOT OPERATE Pump Does Not Operate Is there voltage across the wht/blk and the white wire going to the motor? Is there voltage across terminals ...
Page 83 - Dryer; MOTOR DOES NOT RUN; POSSIBLE CAUSE
800170 81 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 84 - CYCLES ON MOTOR THERMAL PROTECTOR; Installation Instructions
82 800170 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befo...
Page 85 - MOTOR RUNS BUT CYLINDER DOES NOT TURN
800170 83 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer bef...
Page 86 - HEATING ASSEMBLY DOES NOT HEAT OR BURNER DOES NOT IGNITE
84 800170 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befo...
Page 87 - BURNER IGNITES AND GOES OUT REPEATEDLY – GAS MODELS
800170 85 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer bef...
Page 88 - HEATER ASSEMBLY OR BURNER SHUTS OFF PREMATURELY
86 800170 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befo...
Page 89 - HEATER ASSEMBLY OR BURNER DOES NOT SHUT OFF
800170 87 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer bef...
Page 90 - CLOTHES ARE TOO HOT WHEN REMOVED FROM DRYER
88 800170 Section 3 Troubleshooting (Dryer) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befo...
Page 91 - EDC Models – Dryer Control; ERROR CODE LISTING
800170 89 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the was...
Page 92 - CANNOT PERFORM INFRARED COMMUNICATION
90 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 50. CANNOT PERFORM INFRARED COMMUNICATION Attempt to communicate with electronic control from Micro-wand. Aim Micro-wand closer and try again. Yes Yes No No Is there a...
Page 93 - Section 3 Troubleshooting (EDC Models – Dryer Control); COINS IGNORED WHEN ENTERED
800170 91 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ 51. COINS IGNORED WHEN ENTERED Start Coin drop Diagnostic test. Enter several coins Open control panel Check coin drop Make sure control is reset properly and prompti...
Page 94 - ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – DRYER; ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – – DRYER; YES
92 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 52. ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – DRYER The electronic controlhas no LED or VFDfunctioning on thecontrol board. Replace electroniccontrol. OpenControlPan...
Page 95 - ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – DRYER; SCHEMATIC
800170 93 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – DRYER 4 1 2 6 3 MOTOR LIMIT HEATING ELEMENT THERMALFUSE FS-2 H4-4 H3-3 THERMISTOR RELAY "K1" H6-2 H6-1 H4-2 FS-1 D...
Page 96 - AUDIT SWITCH FUNCTION ANALYSIS
94 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 53. AUDIT SWITCH FUNCTION ANALYSIS NO NO Incorrect audit counts: Coin drop. Service door. Coin vault. Cycle. Investigate– Tampering.– Service door and mach. cycle var ...
Page 98 - ELECTRONIC CONTROL ELECTRIC DRYER; NO HEAT ANALYSIS
96 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 54. ELECTRONIC CONTROL ELECTRIC DRYER — NO HEAT ANALYSIS Replace inoperativewiring at terminal block to electronic control. NO HEAT ANALYSIS NO NO During operation an ...
Page 99 - ELECTRONIC CONTROL ELECTRIC DRYER
800170 97 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL ELECTRIC DRYER — NO HEAT ANALYSIS 4 1 2 6 3 MOTOR LIMIT HEATING ELEMENT THERMALFUSE FS-2 H4-4 H3-3 THERMISTOR RELAY "K1" H6-2 H6-1 H4-2 FS-...
Page 100 - ELECTRONIC CONTROL ELECTRIC DRYER —
98 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 55. ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS "Push Start" is flashing and there is no motor run on the dryer. Go through the fo...
Page 101 - ELECTRONIC CONTROL ELECTRIC DRYER —
800170 99 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS 4 1 2 6 3 MOTOR LIMIT HEATING ELEMENT THERMALFUSE FS-2 H4-4 H3-3 THERMISTOR RELAY "K1"...
Page 102 - ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “DOOR OPEN”
100 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 56. ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS Check main powerto dryer. Line voltage to electroniccontrol board. Check and replace inope...
Page 103 - ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “DOOR OPEN”
800170 101 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL ELECTRIC DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS 4 1 2 6 3 MOTOR LIMIT HEATING ELEMENT THERMALFUSE FS-2 H4-4 H3-3 THERMISTOR RELAY "K1"...
Page 104 - ELECTRONIC CONTROL GAS DRYER — NO HEAT ANALYSIS
102 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 57. ELECTRONIC CONTROL GAS DRYER — NO HEAT ANALYSIS Replace inoperativewiring at terminalblock to electroniccontrol. NO HEAT ANALYSIS NO NO During operation an "O...
Page 105 - ELECTRONIC CONTROL GAS DRYER — NO HEAT ANALYSIS
800170 103 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL GAS DRYER — NO HEAT ANALYSIS 4 1 2 6 3 MOTOR SECONDARY COIL HOLDING COIL SENSOR LIMIT FS-2 H4-4 H3-3 THERMISTOR RELAY "K1" H6-2 H6-1 H4-2 ...
Page 106 - ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS
104 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 58. ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS "PUSH START" is flashingand there is no motorrun on the dryer. Go through thefollowing...
Page 107 - ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS
800170 105 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “PUSH START” ANALYSIS 4 1 2 6 3 MOTOR SECONDARY COIL HOLDING COIL SENSOR LIMIT FS-2 H4-4 H3-3 THERMISTOR RELAY "K1&...
Page 108 - ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS
106 800170 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 59. ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS (#) Numbers next to voltage checks correspond to the locations marked on the wiring schematic. ...
Page 109 - ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS
800170 107 Section 3 Troubleshooting (EDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ ELECTRONIC CONTROL GAS DRYER — NO MOTOR RUN — “DOOR OPEN” ANALYSIS 4 1 2 6 3 MOTOR SECONDARY COIL HOLDING COIL SENSOR LIMIT FS-2 H4-4 H3-3 THERMISTOR RELAY "K1&#...
Page 111 - MDC Models – Dryer Control; ERROR CODE LISTING
800170 109 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the wa...
Page 112 - Section 3 Troubleshooting (MDC Models – Dryer Control); COINS IGNORED WHEN ENTERED; Coins Ignored When Entered
110 800170 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 61. COINS IGNORED WHEN ENTERED Does the display on the electronic control increment properly? Is connector H5 on the control firmly seated in its receptacle? Is the 3...
Page 114 - NO VISIBLE DISPLAY ON CONTROL – DRYER; No Display
112 800170 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62. NO VISIBLE DISPLAY ON CONTROL – DRYER Replace the control. Correct wiring between the transformer and the control. Replace the transformer. Are there 24 volts AC ...
Page 115 - NO VISIBLE DISPLAY ON CONTROL – DRYER
800170 113 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ NO VISIBLE DISPLAY ON CONTROL – DRYER 1 2 3
Page 116 - Door Open
114 800170 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 63. DOOR OPEN Replace electronic control. Correct wiring between door switch and control. Also check neutral supply to control. Correct wiring to door switch. Check o...
Page 117 - DOOR OPEN
800170 115 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ DOOR OPEN 1 2 3
Page 118 - MOTOR WILL NOT START; Motor Will Not Start
116 800170 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 64. MOTOR WILL NOT START Is there voltage across terminals 5 and 4 of the motor? Is there voltage across H2-4 and H2-6 on the control? Is there voltage across H2-1 an...
Page 119 - MOTOR WILL NOT START
800170 117 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ MOTOR WILL NOT START 1 2 3
Page 122 - No Heat Gas
120 800170 Section 3 Troubleshooting (MDC Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 66. NO HEAT (GAS) Is there voltage across the pink wire of the gas valve to terminal 2 on the motor? Is there voltage at the output of the limit thermostat referenced...
Page 125 - NetMaster Models – Dryer Control; ERROR CODE LISTING
800170 123 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the wa...
Page 126 - Section 3 Troubleshooting (NetMaster Models – Dryer Control)
124 800170 Section 3 Troubleshooting (NetMaster Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT EC:0A Invalid Machine Type Incorrect machine type. Before downloading, ensure data is for current machine type. EC:19 No Card Reader Communication Communication...
Page 128 - COINS IGNORED WHEN ENTERED
126 800170 Section 3 Troubleshooting (NetMaster Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 68. COINS IGNORED WHEN ENTERED Does the display on the electronic control increment properly? Is connector H5 on the control firmly seated in its receptacle? Is...
Page 129 - NO IR COMMUNICATION; No IR Communication
800170 127 Section 3 Troubleshooting (NetMaster Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ 69. NO IR COMMUNICATION Attempt communication with microwand to the control. Bring microwand closer to the IR window, aim properly and try communication again....
Page 131 - NO DISPLAY
800170 129 Section 3 Troubleshooting (NetMaster Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT\ NO DISPLAY 3 2 1 DRY352S_
Page 134 - MOTOR WILL NOT START
132 800170 Section 3 Troubleshooting (NetMaster Models – Dryer Control) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 72. MOTOR WILL NOT START Is there voltage across terminals 5 and 4 of the motor? Is there voltage across H2-4 and H2-6 on the control? Is there voltage across H...
Page 141 - Section 4; Refer to; Figure 7
800170 139 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the wa...
Page 142 - Section 4 Grounding; Figure 8
140 800170 Section 4 Grounding © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing....
Page 143 - GROUND WIRE FROM TERMINAL BLOCK TO REAR BULKHEAD AND FROM REAR; Figure 9
800170 141 Section 4 Grounding © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing....
Page 144 - WASHER GROUND CONNECTIONS
142 800170 Section 4 Grounding © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing....
Page 145 - Ground Wire
800170 143 Section 4 Grounding © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 10 H004GE3A 1 2 3 5 6 7 8 9 10 11 12 4 Ground Wire From Dryer
Page 146 - GROUND WIRES FROM DRYER TO CONTROL CABINET TO CONTROL PANEL
144 800170 Section 4 Grounding © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing....
Page 147 - Section 5; TO REMOVE THE DRYER
800170 145 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the washer/dryer with any guards/panels removed.• Whenever ground wires ar...
Page 148 - Section 5 Service Procedures; b. Pull top of control panel away from control; Remove control panel
146 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 153 - . Use the lock hole in
800170 151 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 156 - Models Equipped With
154 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 159 - WASHER FRONT PANEL
800170 157 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 161 - WASHER MOTOR CONTROL BOARD
800170 159 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 163 - WASHER LOWER ACCESS PANEL; Panel
800170 161 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 164 - ELECTRIC DRAIN PUMP; a. While supporting the lower access panel,
162 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 165 - NOTE: When installing belt, adjust belt tension per
800170 163 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 169 - WASHER LOADING DOOR; b. Remove door bezel to gain access to nuts. Refer; MODELS WITH THE LETTER “E” IN THE
800170 167 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 170 - WASHER DOOR SEAL AND HOSE
168 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 172 - WASHER DOOR SWITCH
170 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 173 - . This will help relocate motor within the
800170 171 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 175 - OUTER TUB FRONT PANEL
800170 173 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 177 - WASHER INNER BASKET PULLEY; or
800170 175 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 179 - WASHER INNER BASKET ASSEMBLY
800170 177 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 180 - IMPORTANT: Always use new nylon locknuts.
178 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 181 - Inner Basket Installation –
800170 179 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 182 - CROSS SECTION OF BEARING HOUSING SEAL AND TRUNNION SHAFT
180 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 38 FLW1707S Trunnion Shaft Inner Basket Bearing Housing Assembly Apply new grease in lips of bearing housing seal Outer Tub Apply grease to this area Apply anti-seize compound to these ...
Page 184 - Bearing Housing Installation –
182 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 185 - DRYER ACCESS PANEL; Access
800170 183 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 186 - Rear
184 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 187 - LOADING DOOR AND DOOR HINGE
800170 185 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 188 - DRYER INNER AND OUTER DOOR; a. Remove four screws holding door assembly to; DRYER DOOR STRIKE; b. Remove screw holding door strike and bracket
186 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 189 - a. Remove inner door panel from outer door; . The split in the seal must be at the
800170 187 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 190 - DRYER FRONT PANEL AND PANEL SEAL; Door
188 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 191 - DRYER DOOR SWITCH
800170 189 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 193 - DRYER DOOR HINGE
800170 191 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 194 - Complete Gas Valve Assembly.; (2) Gently lower the access panel to disengage
192 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 195 - Burner Tube, Igniter and Bracket
800170 193 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 196 - BURNER HOUSING AND HEAT SHROUD; ELECTRIC MODELS
194 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 198 - . If the seal is installed
196 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 199 - CORRECT WAY; Belt on Wrong Side; INCORRECT WAY
800170 197 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 200 - Impeller and housing.
198 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 201 - Motor Connection Block Terminals; (1) Insert the tool into the block on the back of
800170 199 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 202 - DRYER FRONT BULKHEAD ASSEMBLY
200 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 203 - Front Cylinder Seal; (1) The stitching on the seal must face towards; Bulkhead
800170 201 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 204 - Front
202 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 205 - DRYER CYLINDER ASSEMBLY
800170 203 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 206 - . Belt must be positioned around center
204 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 208 - CYLINDER ROLLERS
206 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 209 - REAR BULKHEAD AND HEATER BOX
800170 207 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 211 - TERMINAL BLOCK OR POWER CORD
800170 209 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 212 - wire to rear bulkhead. Refer to
210 800170 Section 5 Service Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before s...
Page 213 - Section 6; CABINET LEVELING LEGS; CAUTION
800170 211 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the wa...
Page 214 - Section 6 Adjustments; WASHER LOADING DOOR
212 800170 Section 6 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicin...
Page 215 - WASHER MOTOR BELT TENSION
800170 213 Section 6 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicin...
Page 216 - WASHER DOOR CATCH; SHOWN CLOSED
214 800170 Section 6 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicin...
Page 217 - Air
800170 215 Section 6 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicin...
Page 218 - CLEANING COIN DROP
216 800170 Section 6 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicin...
Page 221 - Section 7; NOTE: Drive Motor Resistance
800170 219 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the washer/dryer with any guards/panels removed.• Whenever ground wires ar...
Page 222 - Section 7 Dryer Test Procedures; Motor Switch; (Refer to SECTION 8 for Internal Wiring of the Dryer Motor Switch.)
220 800170 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 223 - Motor Windings
800170 221 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 224 - a. Remove motor and exhaust fan assembly. Refer; Motor with Switch on Blower End
222 800170 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 225 - Motor with switch on pulley end; d. Attach the thermal overload protector removed
800170 223 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 227 - ELECTRICAL CIRCUIT TO IGNITION; Secondary; GAS VALVE FOR SILICON CARBIDE IGNITION; COIL TOLERANCE READINGS; Holding Coil – Terminals 1 & 2
800170 225 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 228 - Silicon Carbide Igniter; SILICON CARBIDE IGNITER AND
226 800170 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 229 - CYCLING OR LIMIT THERMOSTAT; KW
800170 227 Section 7 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer befor...
Page 231 - Section 8
800170 229 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer/dryer before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start the wa...
Page 232 - Section 8 Internal Wiring of Dryer Motor Switch
230 800170 Section 8 Internal Wiring of Dryer Motor Switch © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Notes
Alliance AWN432SP113TW01
User Manual
Alliance ATE50FGP171TW01
User Manual
Alliance AWNE82SP113TW01
User Manual
Alliance AWN432SP113TW04
User Manual
Alliance AWN43RSN115TW01
User Manual