Page 3 - WARNING
F8208501 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are fac...
Page 4 - Table of
© Copyright 2012, Alliance Laundry Systems LLCAll rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 2 F8208501 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT ...
Page 6 - Model Identification
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 4 Model Identification Information in this manual is applicable to these washer-extractor models: HCD020GD2 HCU020GC2 SCD030GD2 SCN080GCF SCU080GLF HCL020GD2 HCU020GD2 SCD040GD2 SCN080GDF SCU080GNF HCL020GN2 HCU020GE2 SCD06...
Page 7 - Preliminary Information; About the Control; Glossary of Terms
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 F8208501 Preliminary Information About the Control This control is a programmable computer that lets the owner control most machine features by setting dip switches and pressing buttons on the back of the control. The control allo...
Page 8 - Control Identification
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 6 Control Identification Figure 1 CHM495R 1 Display 2 Four 7-Segment Digits 3 CYCLE/TEMPERATURE Selector Switch 4 START Switch 5 LED Status Lights 1 2 4 5 3
Page 9 - Display Identification
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7 F8208501 Display Identification Light Emitting Diodes (LEDs)(Refer to Figure 1 ) Light Emitting Diodes (LEDs) are used to indicate the cycle status and door lock information. See below for information on each LED. WASH LED Wash LE...
Page 10 - Washer-Extractor Operation
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 8 Washer-Extractor Operation Start Up When power is applied to the machine, the control will display its software version as “ S xx ” (“ xx ” is the version number) for one (1) second. If the control was not powered down du...
Page 11 - Special Features
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 F8208501 Special Features Programming Control The control allows the machine owner to program the control with the use of buttons on the back of the control. Cycle and vend options may be programmed. For details on programming cyc...
Page 12 - Opening the Top Cover
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 10 Opening the Top Cover To manually program the control, the top cover must be opened. Opening and closing the top cover trips a switch which allows access to various programming options.The top cover is located on the top...
Page 13 - Programming the DIP Switch
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11 F8208501 Programming the DIP Switch There is an 8 position DIP switch on the control board. This switch allows limited programming. 1. To access the DIP switch, open the machine’s top cover. Refer to Opening the Top Cover and Fig...
Page 14 - Entering the Manual Mode; How to Enter the Manual Mode
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 12 Entering the Manual Mode For programming and retrieving information from the control, it is necessary to enter the Manual Mode. How to Enter the Manual Mode 1. Open the top cover. Refer to Opening the Top Cover . 2. Ther...
Page 15 - What Can Be Programmed?; Programmable Options Available
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13 F8208501 Programming Control What Can Be Programmed? This feature allows the owner to program cycle information, vend pricing and other features by using the buttons on the back of the control.This section offers a detailed descr...
Page 20 - How to Program the Vend Price; How to Program Coin #1 Value
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 18 1. Vend Price “AtS” This option allows the owner to set the vend price. How to Program the Vend Price 1. Control must be in Manual Mode. Refer to Entering the Manual Mode . 2. Press the Right or the L...
Page 21 - How to Program Coin #2 Value; Error Codes “ErrS”; How to Program Error Codes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 19 F8208501 3. Coin #2 Value “dEn2” This option allows the owner to set a specific numerical value for a coin entered when using the dual coin drop. For example, the coin value for a dollar coin would be measured...
Page 22 - Coin Audio Beep “CoAU”; How to Program the Coin Audio Beep; Card Display Option “CArd”; How to Program the Card Display Option
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 20 5. Coin Audio Beep “CoAU” This option allows the owner to enable or disable the coin audio beep for each coin insertion. How to Program the Coin Audio Beep 1. Control must be in Manual Mode. Refer to ...
Page 23 - “CyC”; “rCyC”; How to Enter Cycle Programming
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 21 F8208501 7. Total # of Machine Cycles “CyC” This option allows the owner to access Machine Cycle counter audit information. How to Enter Cycle Programming 1. Control must be in Manual Mode. Refer to Entering t...
Page 24 - Prewash Fill Level “PLEU”; How to Program the Prewash Fill Level; Wash Fill Level “ALEU”; How to Program the Wash Fill Level
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 22 9. Prewash Fill Level “PLEU” This option allows the owner to set the prewash fill level to standard or high. How to Program the Prewash Fill Level 1. Control must be in Manual Mode. Refer to Entering ...
Page 25 - “rLEU”; Prewash Enable “PrEn”; How to Program Prewash Enable
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 23 F8208501 11. Rinse #1, #2 and #3 Fill Level “rLEU” This option allows the owner to set the rinse #1, #2 and #3 fill level to standard or high. How to Program the Rinse #1, #2 and #3 Fill Level 1. Control must ...
Page 26 - Prewash Time “PdUr”; How to Program the Prewash Time; How to Program the Wash Time
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 24 13. Prewash Time “PdUr” This option allows the owner to set the duration of the prewash segment of a cycle. How to Program the Prewash Time 1. Control must be in Manual Mode. Refer to Entering the Man...
Page 27 - Intermediate Rinse Spins; How to Program Rinse #2 Enable
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 25 F8208501 15. Intermediate Rinse Spins Enable “SPEn” This option allows the owner to enable or disable intermediate rinse spins for Rinse #1 and Rinse #2 segments. How to Program the Intermediate Rinse Spins En...
Page 28 - Hot Cycle Temperature “FH”; How to Program Hot Cycle Temperature; Warm Cycle Temperature “FHC”; How to Program Warm Cycle Temperature
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 26 17. Hot Cycle Temperature “FH” (Heat Enabled Only) This option allows the owner to program the hot cycle temperature for models equipped with temperature sensing capabilities. How to Program Hot Cycle...
Page 29 - Cycle Pause Enable “CyCP”; How to Program Cycle Pause Enable; Leak Detection During Cycle
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 27 F8208501 19. Cycle Pause Enable “CyCP” (Gravity Drain Models Only) This option allows the owner to enable or disable the cycle pause feature. The cycle pause feature allows the user to pause a cycle within the...
Page 30 - Slow Drain Detection During; Slow Drain Detection
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 28 21. Slow Drain Detection During Cycle Enable “SdEn” This option allows the owner to enable or disable slow drain detection during a cycle. How to Program Slow Drain Detection During Cycle Enable 1. Co...
Page 31 - Number of Balance Retries; Leak Detection Test “Ldt”; How to Access Leak Detection Test
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 29 F8208501 23. Number of Balance Retries “bALr” (Design 2 Models Only) This option allows the owner to program a specific number of retries a load is tried to be balanced. How to Program Number of Balance Retrie...
Page 32 - How to Access Balance Weight Test; DC Bus Display Test “dCbt”; How to Access DC Bus Display Test
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 30 25. Balance Weight Test “bALt” (F-speed Design 1 Models Only) This option allows the owner to test the VFD Balance Switch. How to Access Balance Weight Test 1. Control must be in Manual Mode. Refer to...
Page 33 - DIP Switch Test “dIPt”; How to Access DIP Switch Test; Rapid Advance “rAPd”; How to Enter Rapid Advance
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control 31 F8208501 26. DIP Switch Test “dIPt” This option allows the owner to test the eight DIP switches. How to Access DIP Switch Test 1. Control must be in Manual Mode. Refer to Entering the Manual Mode . 2. Press th...
Page 34 - Exit Manual Mode “End”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8208501 32 28. Exit Manual Mode “End” This option allows the owner to exit the Manual Mode. 1. To exit the Manual Mode, press the Right or Left Programming button to scroll through the programmable options until...
Page 35 - To Enter Production Test Cycle
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33 F8208501 Production Test Cycle To Enter Production Test Cycle NOTE: Machine should be empty of water before starting Production Test Cycle. 1. Disconnect the machine from electrical power.2. Disconnect 2-pin jumper harness, Part ...
Page 36 - To Exit Production Test Cycle
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Production Test Cycle F8208501 34 3. Connect jumper harness to H3 connector on control. Refer to Figure 8 . 4. Reconnect the machine to electrical power.5. Remove jumper harness from control and reconnect to Frame Balance Switch Har...
Page 39 - Error Codes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 37 F8208501 Error Codes Following is a list of possible error codes. Display Description Cause/ Corrective Action E FL Fill Error Programmed water level not reached within 10 minutes in any fill agitate cycle. End cycle. Power down ...
Page 42 - Power Fail Recovery
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208501 40 Power Fail Recovery The Power Fail Recovery feature allows the cycle status to be saved in memory in the event of a power failure.If the power failure lasted less than five (5) seconds, and the door is locked, the cycle ...
Page 43 - Default Cycle Chart
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 41 F8208501 Default Cycle Chart Cycle Steps Hot Wash Warm Wash Cold Wash Delicates Cold Agitation type 18/3/18 Normal 18/3/18 Normal 18/3/18 Normal 3/12/3 Gentle Prewash (ON/OFF) ON ON ON ON Time for agitation (min.) 2 2 2 2 Fill Te...