Alliance HC165 - Manuals

9 2 Environmental Disposal of Unit This appliance is marked according to the European directive 2002/96/ EC on Waste Electrical and Electronic Equipment (WEEE).This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be hand...

10 Explanation of Safety Messages Throughout this manual and on machine decals, you will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific instructions. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining...

11 Important Safety Instructions WARNING To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions: 1. Read all instructions before using the washer.2. Refer to the GROUNDING INSTRUCTIONS in the installation Manual for the p...

12 22 21. Loading door MUST BE CLOSED any time the washer is to fill, tumble, or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open. 22. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warni...

13 Operator Safety WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. To ensure the safety of machine operators, the following maintenance checks must be performed daily:1. Prior to operating the machine, verify that all warnin...

14 3 METRIC US Capacity (dry weight) Ratio [kg/Lit] 1:11 5 kg 11.02 lb. 1:10 5,5 kg 12.13 lb. 1:9 6,1 kg 13.45 lb. Cylinder Diameter 530 mm 20.87 inch Depth 250 mm 9.84 inch Volume 55 Lit 1.94 ft³ Cabinet Height 1038 mm 40.87 inch Width 660 mm 25.98 inch Depth 575 mm 22.64 inch Front loading Diamete...

Label 1 A A 1/2 1/2 1/3 Label 2 26 4 Installation and Connection Instructions The machine (with rubber feet) must be placed on a flat, solid bottom (concrete or fixed ground). When using a metal base or with machines with steam heating, the machine (without feet) must be anchored on the 4 provided l...

A A Label 3 4 27 To prevent damage during transportation, the machine has been equipped with two red transport brackets (A) to eliminate every possible movement of the tub. (See Label 3) After the machine has been placed level, take off the back panel and remove these transport brackets. Warning Rem...

530 [20.87] 660 [25.98] 65 [2.56] Ø18 [Ø0.71 ] 485 [19.09 ] 545 [21.46 ] 30 [1.18 ] 65 [2.56] 30 [1.18 ] 28 4 Mounting Bolt Hole Locations for machines, HC60, IHC012, IHC060 Legend: metric mm [inches]

Ø18 30 [ 1. 18] 30 [ 1. 18] 660 [25.98] 530 [20.87] 65 [2.56] 65 [2.56] 590 [2 3. 23 ] 650 [2 5. 59 ] 29 4 Mounting Bolt Hole Locations for machines, HC65, IHC014, IHC065 Legend: metric mm [inches]

4 648 [25.51] 780 [30.71] 36. 5 [ 1. 44] 36. 5 [ 1. 44] Ø18 [ Ø0. 71] 66 [2.62] 66 [2.58] 665 [2 6. 18] 738 [2 9. 06] 32 Mounting Bolt Hole Locations for machines, HC135, IHC030, IHC135 Legend: metric mm [inches]

34 4 The machine is delivered with hoses with 3/4" connections. These hoses fit the water inlet valves of the machine and the main water inlet taps. All the inlet valves have to be connected. To ensure the optimal functioning of the water inlet valves, the water pressure on the inlet should be b...

4 35 Electrical Installation ImportantElectrical ratings are subject to changes. Refer to serial plate decal for electrical ratings information specific to your machine. WARNING Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to workin...

4 36 The connection should be shielded in a liquid tight or approved flexible conduit with proper conductors of correct size installed in accordance with the National Electric Code or other applicable codes. The connection must be made by a qualified electrician using the wiring diagram provided wit...

4 Label 4 37 Main power connection Connection label: Machine power connections are made at the back of the machine. Three or four conductor power cable is the recommended method (See chapter electrical specs for minimum cable requirements, if local electrical codes exceed these requirements, follow ...

4 39 WARNING The washer-extractor should be connected to an individual branch circuit not shared with lighting or other equipment. Electrical Specifications HC60, IHC012, IHC060 60 liters / 12 pounds Boiler Fed/Steam Heat Electric Heat Code Voltage Cycle Phase Wire Full Load Amps Recommended Circuit...

Label 5 Label 6 4 45 The liquid soap connection consists of 8 connections for liquid soap (See Label 5).The central opening is used for ventilation. Liquid soap connection (option) Connection of the liquid soap hoses WARNING Dangerous Chemicals. May damage eyes and skin. Wear eye and hand protection...

Label 10 Label 11 Label 12 Label 13 4 A 47 Connection of a central operating panel for coin machines (option) WARNING To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not discon...

5 2 3 4 5 3 1 6 7 7 7 48 Steam connection Machines with steam heating must have a steam valve between the steam installation and the machine. WARNING Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam m...

6 Label 14 Label 15 49 Internal connections of the electrical heating NOTE: Other executions are available as options. 3 AC 1 AC Technical remarks Heating 3x230V R5 3x400V R5 4,2kw 3x1,4kw See Label 14 LC1D0901 See Label 15 LC1D0901 6kw 3x2kw See Label 14 LC1D0901 See Label 15 LC1D0901 9kw 3x3kw See...

7 50 Maintenance instruction of the machine  Clean the entire cabinet of the machine regularly and remove all traces of soap, etc....  Remove all detergent residue in the soap dispenser with hot water.  Clean the door gasket and remove all detergents and other products.  Shut off the main water,...

7 A B 51 Important - Clean the drainpipe every 6 months in case drain (B) is used.- The water still being in the drain needs to be drained using drain (A) before cleaning the drainpipe or replacing the exhaust valve.  Verify that the belts are running in the middle of the basket pulley.  Verify th...

8 Label 16 Label 17 52 Contact Information Nameplate Nameplate Location The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. See Labels 16 and 17.

8 53 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact the phone numbers or websites shown on the nameplate. Position of the Serial plate

9 54  In case of important malfunctions and deficiencies, which you cannot resolve yourself, contact your distributor. Repair and after-sales service Machine : Type: ......................................................................................Program: .........................................