Alliance Extractors P232156R9- Manuals

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 5 F232156 Operator Safety To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating the machine, verify that all warning signs are present...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232156 6 Basic Installation/Operation Installation General Specifications UW UniLinc and M30 Control Models Refer to Table 1 . . Specifications 35 60 80 100 125 150 Overall Dimensions Overall width, in (mm) 33.375 (848) (Models thr...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 17 F232156 UniLinc and M30 Control Models Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 6 inches (45 cm) at the sides for maintenance, inspection, and adjustment. Allow at l...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 20 UWAV Models Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 18 inches (45 cm) at the sides for maintenance, inspection, and adjustment. Allow at least 18 inches (45...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 22 UWPV Models Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 18 inches (45 cm) at the sides for maintenance, inspection and adjustment. Allow at least 18 inches (45 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 25 F232156 UW 2 Speed Models with P-Control, S-Control, Mechanical Timer or B-Control Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear, and 18 inches (45 cm) at the sides for maint...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 27 F232156 UW 3 Speed Models with P-Control or S-Control Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 18 inches (45 cm) at the sides for maintenance, inspection, and adjust...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29 F232156 Basic Installation/Operation Operation UW Models With UniLinc Control 1. When display shows the Cycle Menu Screen washer-extractor is ready to be loaded with laundry. 2. On UW35-UW150 models. Press the door unlock button ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 30 NOTE: When washing items which may disintegrate or fragment, such as mop heads or sponges, use laundry nets to prevent drain blockage. IMPORTANT: To prevent out-of-balance conditions, prematur...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 31 F232156 UW Models With M30 Control 1. When display shows a cycle number, the washer- extractor is ready to be loaded with laundry. 2. Press the STOP/UNLOCK button located on the control. Refer to Figu...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 32 NOTE: When washing items which may disintegrate or fragment, such as mop heads or sponges, use laundry nets to prevent drain blockage. IMPORTANT: To prevent out-of-balance conditions, prematur...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 33 F232156 Models Equipped with Both Steam and Electric Heating (UniLinc and M30 Controls) 1. To switch between the heating type, locate the switch on the left side of control module. Refer to Figure 17 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 34 UW Models with S-Control 1. Turn on the main power source (circuit breaker or cut-off switch on the wall). 2. Use left hand to press and hold the Door Unlock button located on the lower right ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 35 F232156 6. Add dry supplies to the supply dispenser compartment cups prior to the start of each cycle. Liquid supplies can be injected directly into the supply dispenser by an external chemical supply...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation F232156 36 UW Models with P-Control Pre-Operating Instructions 1. Turn on the main power source (circuit breaker or cut-off switch on wall). Models with the rotation sensor will display WE-6 Firmware ID ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 37 F232156 4. On UW150 models, use left hand to press and hold the door unlock button located on the door box. Refer to Figure 23 . Figure 23 5. On UW150 models, use right hand to turn door handle counte...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 39 F232156 UW Models with A-Control 1. When display shows “ Cyxx ,” washer-extractor is ready to be loaded with laundry. 2. Use left hand to press and hold the door unlock button located on the lower rig...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Basic Installation/Operation 41 F232156 UW Models with B-Control 1. When display shows “----,” washer-extractor is ready to be loaded with laundry. 2. Use left hand to press and hold the door unlock button located on the lower right...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 43 F232156 Basic Installation/Operation Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This symbol on the product or on its packaging ind...