Alliance C003292ENR1- Manuals

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Safety Information C003292ENR1 4 7. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This appliance is not intended for use by young children or inf...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Safety Information 5 C003292ENR1 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked. Safety Decals Safety decals appear at cr...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Safety Information C003292ENR1 6 Model Identification Information in this manual is applicable to these models: Medium Speed High Speed 40 Pound CP040PMN1 CP040PMQ1CP040PMX2 CPC40M IP040PMN1IP040PMN2 IP040PMQ1 IP040PMX2IPH40M IPH180...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 7 C003292ENR1 Introduction Delivery Inspection Upon delivery, visually inspect crate, protective cover and unit for any visible shipping damage. If the crate, protective cover or unit is damaged or signs of possible damage are evide...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 8 C003292ENR1 Specifications and Dimensions High Speed Models Models Specifications 40H 60H 80H 100H 125H 140H 175H Overall Dimensions Overall Width, in. (mm) 32 (813) 34.5 (876) 42.5 (1080) 42.5 (1080) 50.3 (1278) 50.3 (1278) 50.3 ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 10 Medium Speed Models Models Specifications 40M 60M 80M 100M 140M Overall Dimensions Overall Width, in. (mm) 32 (813) 34.5 (876) 42.5 (1080) 42.5 (1080) 50.3 (1278) Overall Height, in. (mm)...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 12 Machine Dimensions Dimensional Clearances Allow 24 inches (600 mm) at the rear of the machine and 18 inches (450 mm) is recommended at the sides for maintenance, inspection and adjustment...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 13 C003292ENR1 40 Pound Models PHM727N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Steam Inlet 4 Cold Water 9 Auxiliary Drain 5 Greasing Poin...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 14 60 Pound Models PHM728N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Auxiliary Drain 4 Cold Water 9 Drain 5 Greasing Points 10 ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 15 C003292ENR1 80 Pound Models PHM729N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Auxiliary Drain 4 Cold Water 9 3 in. (76.2 mm) Drain 5 Gre...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 20 Floor Load Data Ma chine Size Bask et Diamet er Net Wt. of Ma chine (lbs .) He ight of Bask et Ce nte r (in.) Ma x RPM G Cal- cu la te d S tatic Load (lbs .) S ta tic Floor Pres su re (l ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 21 C003292ENR1 Installation Instructions Surface These machines must be securely anchored on a solid, flat reinforced concrete surface capable of withstanding the weight of the machine and the considera...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 22 Clearances IMPORTANT: If the machines are to be mounted less than 18 in. (457 mm) from each other or less than 18 in. (457 mm) from a side wall, only the inside bolt holes will be accessi...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 23 C003292ENR1 Mounting Bolt Hole Locations Use a sturdy template to guide hammer-drill into floor. A heavy steel template/drill guide is available from your distributor.Make sure to follow bolt manufac...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 24 Mounting Bolt Hole Locations IMPORTANT: All drawings are not to scale. 40 Pound Models Figure 11 PHM763N F A L C G J M H K D E B I FRONT OF MACHINE REAR OF MACHINE WALL N P O 24 in. (610 ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 30 Water Connection Water service should have the following: • Hot water temperature should be a maximum of 190°F (88°C). • Water pressure should be between 30 and 85 psi (2 to 7 bar). • Ins...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 31 C003292ENR1 Drain Connection Requirements A flexible connection must be made to a vented drain system to prevent an air lock and to prevent siphoning. IMPORTANT: Machines must be installed in accorda...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 32 Figure 15 NOTE: Installation of additional machine will require proportionately larger drain connections. PHM621N 1 Rear of Machine 2 Drain Pipe 3 1 in. (25.4 mm) Minimum Air Gap 4 Steel ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 33 C003292ENR1 Electrical Installation Requirements IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine. Electrical con...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 34 The AC drive provides thermal overload protection for the drive motor. However, a separate circuit breaker or electrical supply disconnecting device must be installed for complete electri...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 36 Making Connections to Machine After electrical service feeder has been installed and electrical service voltage verified by a volt meter, follow this procedure to connect service to the e...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 37 C003292ENR1 Steam Requirements (Steam Heat Option Only) For machines equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements are s...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions C003292ENR1 38 Chemical Injection Supply System IMPORTANT: Undiluted chemical dripping can damage the machine. All chemical injection supply dispenser pumps and dispenser tubing should be mounted below ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Specifications and Dimensions 39 C003292ENR1 Figure 19 Connection of Chemical Pump Signals To connect pump control to AC voltage signals, do the following: 1. Remove large rear electrical module cover on machine to access chemical t...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 41 C003292ENR1 Operation General Operation Instructions 1. Open door.2. Load to capacity. DO NOT OVERLOAD. 3. Close and lock door. 4. Enter number of desired program. 5. Fill dispenser cups with appropriate chemicals, if necessary. ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Operation C003292ENR1 42 7. Machine door will automatically lock and cycle will begin. 8. When program is completed, display will display “open door” and door will automatically unlock and is ready to be opened. The PS40’s fault cod...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 43 C003292ENR1 Maintenance Maintenance procedures described below will prolong life of machine and help prevent accidents. Daily Beginning of Day 1. Check door interlock before starting operation: a. Attempt to start with door open....

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Maintenance C003292ENR1 44 Weekly 1. Check machine for leaks. a. Start an unloaded cycle to fill machine.b. Verify that door and door gasket do not leak.c. Verify that drain valve is operating and that drain system is free from obst...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Maintenance 45 C003292ENR1 3. Verify V-belts are properly aligned by checking pulley alignment. Place a straight edge across both pulley faces. The straight edge should make contact with pulleys in two places. Refer to Figure 25 . F...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT Maintenance C003292ENR1 46 Care of Stainless Steel • Remove dirt and grease with detergent and water. Thoroughly rinse and dry after washing. • Avoid contact with dissimilar metals to prevent galvanic corrosion when salty or acidic ...

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 47 C003292ENR1 Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).This symbol on the product or on its packaging indicates that this product s...