Page 3 - Table of; Burner Ignites and Goes Out Repeatedly –
© Copyright 2010, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 803404 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT T...
Page 4 - Washer Will Not Fill
2 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29. Washer Will Not Fill (Machine Empty, No “E SP” on Display)...................................48 30. Washer Overflows.......................................................................5031. Pump or Drain Valve Does N...
Page 5 - Section 1; DANGER; WARNING
803404 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 1 Safety Information Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,” “WARNING” and “DANGER”) followed by specific instructions. These precautions are intended for the...
Page 6 - Locating an Authorized Servicer; reconnected to ensure that the machine is properly grounded.
4 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when i...
Page 7 - Section 2; Customer Service
803404 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 2 Introduction Customer Service If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address ...
Page 8 - Model Identification
6 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Model Identification Information in this manual is applicable to these washer/dryer models. BT3LLFSG401UN01BT3LLFSG401UW01BT3LLFSP401UN01BT3LLFSP401UW01BT3LXFSG401UN01BT3LXFSG401UW01BT3LXFSP401UN01BT3LXFSP401UW...
Page 9 - Theory of Operation
803404 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Theory of Operation SWD1687S WASHER DRYER Pressure Switch (Located inside control cabinet) Electronic Control (Mounted to back side of control panel) Electric Drain Pump (or Drain Valve) Motor Outer Tub Inner B...
Page 12 - Section 3; Troubleshooting Coin Drop
10 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 3 General Troubleshooting 1. Troubleshooting Coin Drop a. Non-Electronic Coin Drops: When coin is placed into coin slot, the coin should roll down drop and be heard dropping into coin vault. If coin does not fall i...
Page 13 - Troubleshooting Coin Drop
803404 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting Troubleshooting Coin Drop Is machine level? (Machines that aren't level may prevent coins from following through required check stages of drop.) No Yes No Refer to wiring diagram for proper connecti...
Page 14 - Remove Coin Drop From Machine
12 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting b. Electronic Coin Drops: If coin drop is not accepting coins, perform the following: (1) Clean coin drop. Refer to Paragraph 55. (2) On electronic coin drops with an old-style tension spring (shown...
Page 15 - Reinstall Coin Drop Into Machine
803404 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting (6) Rotate spring clockwise, 40 to 60 degrees, until it is free from right tabs. Refer to Figure 6 . (7) Use screwdriver to remove spring from center tab. Refer to Figure 6 . (8) Lift spring, with a...
Page 16 - Washer Motor Circuit; To correct this condition, replace the belt.
14 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting 2. Washer Motor Circuit 3. Troubleshooting Knocking Noise If a frontload washer produces a noise similar to a knock on a door, it might be due to a flat spot on the belt. The knocking sound is made ...
Page 17 - normally closed
803404 15 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer...
Page 18 - Troubleshooting LEDs on; DO NOT
16 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General Troubleshooting To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer...
Page 20 - Section 4
18 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 4 Dryer Troubleshooting IMPORTANT: Refer to wiring diagram for aid in testing dryer components. To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the ...
Page 21 - Dryer Motor Does Not Run
803404 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 7. Dryer Motor Does Not Run Dryer motor does not run. Is power cord plugged in? Plug in cord. Is electrical power off or fuse blown? Check laundry room for blown or loose fuse(s), or open circuit brea...
Page 22 - Dryer Stops In Cycle Quits After The First Few Loads Has A Burning
20 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 8. Dryer Stops In Cycle; Quits After The First Few Loads; Has A Burning Smell; Cycles On Motor Thermal Protector Dryer stops in cycle, quits after first few loads, has burning smell or cycles on motor...
Page 23 - Dryer Motor Runs But Cylinder Does Not Turn
803404 21 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 9. Dryer Motor Runs But Cylinder Does Not Turn Dryer motor runs but cylinder does not turn. Is motor drive pulley loose? Tighten pulley. Is belt installed on pulley? No Install belt. No Is cylinder be...
Page 24 - Dryer Motor Does Not Stop
22 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 10. Dryer Motor Does Not Stop Dryer motor does not stop. Is wiring to motor switch incorrect? Refer to wiring diagram. Yes Is motor centrifugal switch sticky or plugged with lint? No Remove dust or li...
Page 25 - Dryer Runs Only When Door is Open
803404 23 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 11. Dryer Runs Only When Door is Open Dryer runs only when door is open. Is door switch miswired? Rewire door switch. Refer to wiring diagram. Yes SWD1693S Replace door switch. No
Page 26 - Dryer Heating Assembly Does Not Heat or Burner Does Not Ignite
24 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 12. Dryer Heating Assembly Does Not Heat or Burner Does Not Ignite Dryer heating assembly does not heat or burner does not ignite. Is exhaust system improper or inadequate? Refer to Installation Instr...
Page 28 - Igniter Does Not Glow (Gas Supply Sufficient) – Gas Dryer Models
26 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 13. Igniter Does Not Glow (Gas Supply Sufficient) – Gas Dryer Models Gas dryer models: Igniter does not glow (gas supply sufficient). Is there power to power leads on valve (pink and blue wires)? Chec...
Page 29 - Burner Ignites and Goes Out Repeatedly – Gas Dryer Models
803404 27 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 14. Burner Ignites and Goes Out Repeatedly – Gas Dryer Models Gas dryer models: Burner ignites and goes out repeatedly. Is exhaust system improper or inadequate? Refer to Installation Instructions (su...
Page 30 - Igniter Glows But Burner Does Not Ignite – Gas Dryer Models
28 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 15. Igniter Glows But Burner Does Not Ignite – Gas Dryer Models Gas dryer models: Igniter glows but burner does not ignite. Did sensor fail in closed position? Replace sensor. Yes Is secondary coil or...
Page 31 - Dryer Heater Assembly Or Burner Shuts Off Prematurely
803404 29 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 16. Dryer Heater Assembly Or Burner Shuts Off Prematurely Dryer heater assembly or burner shuts off prematurely. Is exhaust system improper or inadequate? Refer to Installation Instructions (supplied ...
Page 32 - Dryer Heater Assembly or Burner Repeatedly Cycles Off On Limit
30 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 17. Dryer Heater Assembly or Burner Repeatedly Cycles Off On Limit Thermostat Dryer heater assembly or burner repeatedly cycles off on limit thermostat. Is external exhaust system longer or providing ...
Page 34 - Dryer Heater Assembly or Burner Does Not Shut Off
32 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 18. Dryer Heater Assembly or Burner Does Not Shut Off Dryer heater assembly or burner does not shut off. Is motor switch inoperative? (Must be in a heat setting.) Test switch and replace if inoperativ...
Page 35 - Clothes Do Not Dry in Dryer
803404 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 19. Clothes Do Not Dry in Dryer Clothes do not dry in dryer. Does heater assembly not heat or burner not ignite? Refer to Dryer Heating Assembly Does Not Heat or Burner Does Not Ignite paragraph. Yes ...
Page 36 - Clothes Are Too Hot When Removed From Dryer
34 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 20. Clothes Are Too Hot When Removed From Dryer Clothes are too hot when removed from dryer. Is exhaust system improper or inadequate? Refer to Installation Instructions (supplied with unit) for exhau...
Page 37 - Excessive Chattering Or Vibrating Noise in Dryer
803404 35 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 21. Excessive Chattering Or Vibrating Noise in Dryer Excessive chattering or vibrating noise in dryer. Is idler spring inoperative? Remove lower access panel. Set dryer to normal cycle and allow it to...
Page 38 - Excessive Humming Or Whistling Noise in Dryer
36 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dryer Troubleshooting 22. Excessive Humming Or Whistling Noise in Dryer Excessive humming or whistling noise in dryer. Is blower housing inoperative? If the abnormal operating noise is loudest at the vent exit, the problem...
Page 39 - Section 5; Error Code Listing; Display; Transmission Failure
803404 37 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 5 Washer Electronic Control Troubleshooting 23. Error Code Listing Following is a list of possible error codes for an electronic control. Errors beginning with “EI” refer to external device Infra-red communication ...
Page 41 - Coin Error
803404 39 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting E rr Coin Error Invalid coin pulse or inoperative coin sensor. Check coin drop area and remove obstructions. If error persists, tampering may have occurred. Evaluate security proce...
Page 42 - PDA Does Not Communicate With Control
40 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 24. PDA Does Not Communicate With Control Attempt to communicate with the electronic control u s in g the PDA. I s there acknowled g ement from the control ? Check PDA manual for c...
Page 43 - Coins Ignored When Entered
803404 41 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 25. Coins Ignored When Entered S tart Production Te s t Cycle and advance to Coin Drop s tep. Re s et control to ready mode. Ye s No I s "H5" connector properly s eated on ...
Page 44 - No Visible Display on Control; Control Ha
42 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 26. No Visible Display on Control Control Ha s No Vi s ible Di s play The electronic control ha s no LED or VFD functionin g on the control board. I s the power cord plu gg ed in ?...
Page 45 - No Visible Display on Control
803404 43 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting No Visible Display on Control FLW1779 S 2 3 1 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 46 - Washer Will Not Start – “door” Displayed
44 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 27. Washer Will Not Start – “door” Displayed Wa s her will not s tart. Vend s ati s fied. I s there 220-240 VAC (or 120 VAC) * acro ss "H 3 -5" and "H7-5" on the co...
Page 47 - Washer Will Not Start – “door” Displayed
803404 45 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting Washer Will Not Start – “door” Displayed FLW1779 S 2 1 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 48 - Washer Will Not Start – “E dL” on Display
46 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 28. Washer Will Not Start – “E dL” on Display I s there 220-240 VAC (or 120 VAC) * acro ss terminal s "H 3 -4" and "H7-5" on the electronic control ? (1) No Ye s Wa...
Page 49 - Washer Will Not Start – “E dL” on Display
803404 47 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting Washer Will Not Start – “E dL” on Display FLW1779 S 1 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 52 - Wa
50 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 30. Washer Overflows Wa s her Overflow s I s there 220-240 VAC (or 120 VAC) * to the over level terminal on pre ss ure s witch to neutral ? Ye s No Replace inoperative pre ss ure s...
Page 53 - Washer Overflows
803404 51 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting Washer Overflows FLW1779 S 2 2 1 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 54 - Pump or Drain Valve Does Not Operate
52 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 31. Pump or Drain Valve Does Not Operate I s there 220-240 VAC (or 120 VAC) * acro ss the wht/blk and the white wire g oin g to the pump or drain valve ? I s there 220-240 VAC (or ...
Page 55 - Pump or Drain Valve Does Not Operate
803404 53 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting Pump or Drain Valve Does Not Operate FLW1779 S 2 1 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 57 - Serial Communication Error (“E SP” on Display)
803404 55 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting Serial Communication Error (“E SP” on Display) FLW1779 S 3 2 1 4 Refer to washer nameplate on rear panel for proper voltage and Hertz
Page 58 - Motor doe
56 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Washer Electronic Control Troubleshooting 33. Motor Does Not Run (“E dF” on Display) Motor doe s not run (E:df on di s play) (1) No I s there continuity between motor terminal s? Refer to value s at ri g ht. Ye s Check mot...
Page 64 - Section 6
62 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 6 Dryer Electronic Control Troubleshooting IMPORTANT: Refer to wiring diagram for aid in testing dryer components. To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all ele...
Page 65 - Description
803404 63 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 36. Error Codes Following is a list of possible error codes. Display Information Description Cause/Corrective Action Right most DP (decimal point) Lit Network Communication Error Co...
Page 66 - Coins Ignored When Entered
64 803404 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 37. Coins Ignored When Entered Does the display on the electronic control increment properly? Is connector H5 on the control firmly seated in its receptacle? Is the 3 pin connector ...
Page 67 - No IR Communication
803404 65 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38. No IR Communication Attempt to communicate with control using PDA. Is there a response of any kind from the control? Check PDA manual for correct use of IR. No DRY1859S Check PD...
Page 68 - No Di
66 803404 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 39. No Display Replace the control. Correct wirin g between the tran s former and the control. Replace the tran s former. Are there 24 volt s AC acro ss terminal s H1- 3 and H1-1 on...
Page 69 - No Display
803404 67 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT No Display DRY1 8 6 3S 1 2 3
Page 71 - Door Open
803404 69 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Door Open DRY1 8 6 3S 1 2 3 4
Page 72 - Motor Will Not Start
70 803404 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 41. Motor Will Not Start Is there voltage across terminals 5 and 4 of the motor? Is there voltage across H 3 -4 and H 3 -6 on the control ? Is there voltage across H 3 -1 and H 3 -6...
Page 73 - Motor Will Not Start
803404 71 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Motor Will Not Start DRY1 8 6 3S 1 2 3
Page 74 - No Heat Electric
72 803404 Dryer Electronic Control Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 42. No Heat (Electric) I s there volta g e acro ss the lead s to the heatin g element ? I s there volta g e from the output s ide of the limit thermo s tat to L2 ? I s there volta g...
Page 78 - Section 7; Cabinet Leveling Legs; does not rock; CAUTION
To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before servicing.• Never start machine with any guards/panels removed.• Whenever ground wires are rem...
Page 79 - Washer Loading Door; b. The loading door can be adjusted up or down
803404 77 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 80 - Washer Motor Belt Tension
78 803404 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 81 - Washer Door Catch
803404 79 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 82 - HOWN CLO
80 803404 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 85 - Drop
803404 83 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 87 - Cleaning Electronic Coin Drop; a. Disconnect electrical power to machine and; Coin Drops with Old-Style Spring (refer to; (1) Move spring downward until cover catch is
803404 85 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 88 - d. Clean the coin path with a soft brush and wipe
86 803404 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 89 - f. Clean light sensors with a soft brush or air; Coin Drops with OLD-Style Spring; spring back over cover catch.
803404 87 Adjustments © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before serv...
Page 90 - Section 8; Refer to; NOTE: Drive Motor Resistance
88 803404 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before servicing.• Neve...
Page 91 - Motor Switch; (Refer to SECTION 10 for Internal Wiring of the Dryer Motor Switch.)
803404 89 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 92 - Motor Windings
90 803404 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 93 - a. Remove motor and exhaust fan assembly.; Motor with Switch on Blower End
803404 91 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 94 - Motor with switch on pulley end; d. Attach the thermal overload protector
92 803404 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 95 - Burner System Operation
803404 93 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 96 - Electrical Circuit To Ignition; Figure; COIL TOLERANCE READINGS; GAS VALVE FOR SILICON CARBIDE IGNITION
94 803404 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 97 - Silicon Carbide Igniter; SILICON CARBIDE IGNITER AND
803404 95 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 98 - Cycling or Limit Thermostat
96 803404 Dryer Test Procedures © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer b...
Page 100 - Section 9
803404 98 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect all electric power to the machine and accessories before servicing.• Close gas shut-off valve to gas dryer before servicing.• Neve...
Alliance AWN432SP113TW01
User Manual
Alliance ATE50FGP171TW01
User Manual
Alliance AWNE82SP113TW01
User Manual
Alliance AWN432SP113TW04
User Manual
Alliance AWN43RSN115TW01
User Manual