Alliance 907003062 - Manuals

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 4 70420801 (EN) Steam Requirements ........................................................................... 43 Piping Recommendations ..................................................................... 43Installing Steam Trap a...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 70420801 (EN) Introduction Model Identification Information in this manual is applicable to these models. Includes models with the following control suffixes: Customer Service If literature or replacement parts are required, conta...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 70420801 (EN) 6 Serial Plate Location When calling or writing for information about your product, be sure to mention model and serial numbers.Model and serial numbers are located on the serial plate as shown. TMB2288N 1...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7 70420801 (EN) Safety Information Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal saf...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 70420801 (EN) 8 Save These Instructions Important Safety Instructions 1. Read all instructions before using the tumble dryer. 2. Refer to the Grounding Instructions for the proper grounding of the tumble dryer. 3....

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 9 70420801 (EN) 22. Install this tumble dryer according to this Installation Manual . All connections for electrical power, grounding and gas supply must comply with local codes and be made by licensed personnel w...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70420801 (EN) 10 Specifications and Dimensions N/A = Not Applicable Specifications 120 Pound 170 Pound Noise level measured during operation at operator position of 3.3 feet (1 meter) in front of machine and 5.2 feet (1.6 meters) fr...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 11 70420801 (EN) 120 Pound Tumble Dryer Dimensions and Exhaust Outlet Locations Refer to Position and Level the Tumble Dryer to temporarily reduce the heights of these models. TMB2326N TMB2326N A B C D ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 13 70420801 (EN) Electric and Gas Connection Locations for Gas Models NOTE: These figures are approximate dimensions only. TMB2255N A C C A D B B D 120L/N 170L/N Models Electrical Connection Gas Connect...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70420801 (EN) 16 Installation Pre-Installation Inspection Upon delivery, visually inspect the crate, carton and parts for any visible shipping damage. If the crate, carton or cover is damaged or signs of possible damage are evident,...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 17 70420801 (EN) IMPORTANT: Install tumble dryers with sufficient clearance for servicing and operation. Refer to Figure 1 . Figure 1 To reduce the risk of serious injury, install lockable door(s) to prevent public acce...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70420801 (EN) 18 Position and Level the Tumble Dryer The tumble dryer may be moved with or without the skid. To remove the skid, unscrew the four shipping bolts, and discard them.To fit a 170 pound tumble dryer (with sh...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 19 70420801 (EN) 9. Check the airflow switch operation by opening the lint panel; be sure to remove shipping tape from airflow switch prior to operation. Temporarily tape down the lint panel safety switch located behind...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70420801 (EN) 20 Installing CE Gas Drying Tumble Dryers General Information This information is to be used when installing gas tumble dryers in countries, and/or on gases, different than the machine’s factory configurat...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 21 70420801 (EN) Gases and Configurations Burner orifice information at 0-2000 feet (0-600 meters) altitude.* For Natural Gas, Group E+ applications, convert using L.P. Gas model and replace burner orifices. ** For L.P....

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70420801 (EN) 22 Basic Configuration 1. Determine the necessary conversion operations to convert from the factory-supplied configuration to the desired configuration. 2. Perform the conversions required so the machine i...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 23 70420801 (EN) Specific Conversion Procedures How to Convert Gas Valve from Regulated to Unregulated NOTE: Conversion from regulated to unregulated is only needed when regulated tumble dryers were ordered, but unregul...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70420801 (EN) 24 Figure 3 How to Adjust Gas Valve Governor/Regulator 1. Check gas burner orifice (manifold) pressure as follows. Refer to Figure 3 . 2. Remove screw plug from inside pressure tap.3. Connect a “U”-tube ma...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 25 70420801 (EN) Exhaust Requirements Layout Wherever possible, install tumble dryers along an outside wall, where duct length can be kept to a minimum and makeup air can be easily accessed. Construction must not block the airflow a...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 70420801 (EN) 26 NOTE: Exhaust ducts must be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in strength and corrosion resistance to ducts made of galvanized sheet stee...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 27 70420801 (EN) Individual Venting For maximum efficiency and performance, it is preferred to exhaust tumble dryer(s) individually to the outdoors. IMPORTANT: At no point may the cross sectional area of install...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 70420801 (EN) 28 Figure 7 NOTE: Do not install wire mesh or screen in exhaust duct opening to avoid lint build-up or impacting proper discharge of air from tumble dryers. NOTE: Where exhaust duct pierces a combu...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 29 70420801 (EN) Figure 8 TMB2019N 1 NOTE: Where the exhaust duct pierces a combustible wall or ceiling, the opening MUST be sized per local codes. 2 Outlet Duct Diameter 3 45° Typical L K J I H G F E D C B A 3 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 31 70420801 (EN) Gas Requirements IMPORTANT: Any product revisions or conversions must be made by the Manufacturer’s Authorized Dealers, Distributors or local service personnel. IMPORTANT: The installation must comply with local cod...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements 70420801 (EN) 32 Figure 10 Turn on gas and check all pipe connections (internal and external) for gas leaks with a non-corrosive leak detection fluid. Purge air in gas service line by operating the tumble dryer in t...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements 33 70420801 (EN) Gas Supply Pipe Sizing and Looping Figure 11 TMB2126N 1 Gas Furnace (120,000 Btu/hr.) 8 25 ft. (7.6 m) 2 Gas Water Heaters (400,000 Btu/hr. each) 9 Main Regulator 3 Gas Space Heaters (70,000 Btu/hr....

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements 35 70420801 (EN) High Altitude Orifice Sizing For proper operation at altitudes above 2000 feet (610 meters), the gas orifice size must be reduced to ensure complete combustion. Refer to Table 8 . For CE models, con...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70420801 (EN) 36 Electrical Requirements NOTE: To ensure protection against shock, this tumble dryer MUST be electrically grounded in accordance with the local codes or, in the absence of local codes, with the latest edition of the ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 37 70420801 (EN) For CE Models Only All models are factory-equipped with an emergency stop button on the front panel. NOTE: Activation of the emergency stop switch stops all machine control circuit functions,...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70420801 (EN) 38 Service/Ground Location Model Ground and Terminal Block Locations Non-CE Gas and Steam CE Gas and Steam Figure 12 (continued) Ground TMB2269N Electrical Service Terminal Block Junction Box Gr...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70420801 (EN) 40 To Connect Electrical Service to the Tumble Dryer NOTE: The wiring diagram is located in the junction or contactor box. 1. Install a circuit breaker as close to the tumble dryer as possible. ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 41 70420801 (EN) Jumper Configuration Instructions Changing the transformer configuration jumper is required, PRIOR TO SUPPLYING POWER TO THE MACHINE , if any of the following apply: IMPORTANT: Failure to ins...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70420801 (EN) 42 Electrical Requirements Refer to Table 9 . NOTE: Minimum wire sizes are obtained from Canadian Electrical Code and are intended for use as a guideline only. Electrical connections should be m...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 43 70420801 (EN) Steam Requirements NOTE: Machines require a constant 80 to 100 psig (5.62 to 7.03 kg/sq. cm) steam service for optimum operation. The maximum allowable steam pressure for use with 60 Hertz or 50 Hertz tumble dryers ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements 70420801 (EN) 44 Installing Steam Trap and Making Condensate Return Connections The steam trap must be installed and the coil outlet connections must be connected to the condensate return lines. The following step...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements 45 70420801 (EN) 120 Pound Tumble Dryers Figure 14 TMB2014N NOTE: Refer to Table 10 for sizing of steam lines. Piping must also be sized accordingly for length of runs and number of elbows. 1 Supply 8 18 in. (457 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements 70420801 (EN) 46 170 Pound Tumble Dryers Figure 15 TMB2024N NOTE: Refer to Table 11 for sizing of steam lines. Piping must also be sized accordingly for length of runs and number of elbows. 1 Risers 12 in. (305 mm...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 47 70420801 (EN) Adjustments Gas Burner Air Shutter NOTE: Air inlet shutters on the burner must be adjusted so sufficient air is metered into the system for proper combustion and maximum efficiency. Before adjusting the inlet shutte...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Adjustments 70420801 (EN) 48 Airflow Switch The airflow switch is set at the factory for proper operation. No adjustment necessary.The airflow switch operation may be affected by shipping tape still in place, lack of make-up air, or...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Adjustments 49 70420801 (EN) Belt Drive The drive assemblies consist of motors, belts, eyebolts and a step pulley.The pulley diameters are sized to produce a cylinder speed of 37-39 RPM for 120 pound models or 29-31 RPM for 170 poun...