Alliance 35- Manuals

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 5 9001000 Operator Safety To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating the machine, verify that all warning signs are present and legib...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001000 6 Introduction Model Identification Information in this manual is applicable to these models: 18 HX18PVQM6 SX18PVPA7 UX18PVNA6 HX18PVQU6 SX18PVQU6 UX18PVNU6 HX18PVQM7 SX18PVQM6 UX18PVNA7 HX18PVXU6 SX18PVXU6 UX18PVPU6 HX18PVX...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 9001000 8 Nameplate Location The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Figure 1 Replacemen...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 9 9001000 * Denotes Brand Figure 2 Model Number Familiarization Guide Sample Model Number: *X55PVXM60001 *X Model Number Prefix 55 Washer-Extractor Capacity (pounds dry weight of laundry) P Type of Electrical Control (P...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001000 10 Specifications and Dimensions General Specifications Model 18 25 33 35 40 Overall Dimensions Overall width 26 in. (660 mm) 26 in. (660 mm) 30.71 in. (780 mm) 30.8 in. (783 mm) 30.71 in. (780 mm) Overall height 40.6 in. (1...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 25 9001000 Installation Dimensional Clearances Table 1 shows recommended minimum clearances on all sides of the washer-extractor. Recommended Minimum Clearances Model 18 25 33 35 40 55 75 100 135 165 200 Minimum rear clearance 24 in...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 26 Machine Foundation Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract. The washer-extractor ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 27 9001000 Mechanical Installation Frame Dimensions and Mounting Bolt Location 18, 25, 35, 55, 75, 100, 135 and 165 Pound Capacity with U in the 8th position of the Model Number (e.g. *X18PVXU6) Figure 14 IMPORTANT: Dra...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 41 9001000 Mounting Bolt Installation (If Required) After the concrete has cured and the anchors are installed, proceed as follows: 1. Place the washer-extractor adjacent to the foundation. Do not attempt to move it by ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 42 Removing the Transport Brackets To prevent damage during transportation, the machine has been equipped with four red transport brackets (refer to Figure 29 for 18, 25 and 35 models; refer to Figure 30 for 33 ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 44 Drain Connection A drain system of adequate capacity is essential to washer-extractor performance. Ideally, the water should empty through a vented pipe directly into a sump or floor drain. Figure 33 shows dr...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 46 Water Connection The 18-135 models are delivered with hoses with 3/4 inch hose connectors. The 165 model is delivered with 3 x 1 inch and 1 x 3/4 inch hose connectors. These hoses fit the water inlet valves o...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 47 9001000 Electrical Installation The AC inverter drive requires a clean power supply free from voltage spikes and surges. A voltage monitor should be used to check incoming power. The customer’s local power company ma...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 50 Electrical Connection Remove the cover plate at the back of the machine. Using copper conductors only, connect the power cable to the connectors. Refer to the instructions listed on the machine’s decal on how...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 51 9001000 Steam Requirements (Steam Heat Option Only) For washer-extractors equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements are shown in Tabl...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 52 Supply Programming Table When programming a supply step on the WE-8, choose between 9 different supply steps. Refer to Table 8 . NOTE: The Supply button is button 6. Supply Relay Configuration (No Wiring) * L...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 53 9001000 Supply relay 1 controls terminals 1 and 2. Figure 36 shows the jumper wire from terminal 13 (L1 220 VAC) to all other even pins (i.e., 2, 4, 6…). This applies L1 ( 220 VAC) to terminal 2. When supply 4 on the...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 9001000 54 Out-of-Balance Switch Figure 40 The out-of-balance switch is mounted on the upper right side on the back of the control panel. There is a window around the probe of the switch that is mounted on the movable p...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 55 9001000 Control Function Test The washer-extractor should be cleaned after the installation is complete. A function test should then be executed on the unloaded machine: 1. Verify that power supply voltage and phase ...