AIWA TV 2002 - Manuals - manualsarea.com

Page 5 - Service Technical Information

1/1 Service Technical Information MODEL NO. TV F2000 / F2400 − SUBJECT Notes on repairing flat CRT TV set REF.No. :G 99 076 E0 − − − DATE :02. MAR. 2000 <CONTENTS> Pay attention to the following notes when repairing flat CRT a TV set. When repairing a unit, DO NOT LEAVE the degaussing cable di...

Page 8 - M arkin g of t w o w hite d ots

1/1 Service Technical Information MODEL NO. TV AT215 − SUBJECT The remote control is not effective REF.No. :G A0 035 E0 − − − DATE :05. JUN. 2000 <CONTENTS> In this set, after successive operations of changing the channel are made using the rem otecontrol, there are times when the remote contr...

Page 9 - IC Protector

1/1 Service Technical Information MODEL NO. TV C202 − TV C202S − SUBJECT No power REF.No. :G A0 117 E0 − − − DATE :02. MAR. 2001 <CONTENTS> No power due to open IC PROTECTOR (ICP,PR 801) caused by a rush current. <COUNTERMEA SURE> Replace the IC Protector (PR801 1.5A)with one that has hi...

Page 10 - Distinction Switch setting up procedure

1/2 Service Technical Information MODEL NO. TV SA2151/A2118/A2110/A2018/A2010 − SUBJECT REF.No. :G A0 125 E0 Distinction Switch setting up procedure − − − DATE :10. APR. 2001 <CONTENTS> Setup procedure for Distinction Switch was not described in the service manuals below. TV SA2151 09 007 420 ...

Page 11 - Distinction switch set up data for each model

2/2 1 : K E 1 5 : S H 1 1 : K E 1 5 : S H 1 2 : K E 2 6 : S H 2 6 : S H 2 2 : K E 2 3 : I N D O 1 Red 3 : I N D O 1 7 : S H 3 7 : S H 3 4 : I N D O 2 8 : S H 4 4 : I N D O 2 8 : S H 4 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 1 0 1 0 0 0 0 1 1 1 1 0 0 0 1 1 0 0 1 0 0 0 0 1 1 ...

Page 12 - A d d i t i o n al Ci r c u i t

1/1 Service Technical Information MODEL NO. TV F2000 / F2100 / F2400 / F2500 − SUBJECT Vertical line appears on the screen REF.No. :G A1 011 E0 − − − DATE :06. JUN. 2001 <CONTENTS> A vertical line may appear on TV screen when VCD player or DVD player is connected toinput term inal for playback...

Page 15 - Black marking; VCC; Old

1/1 Service Technical Information MODEL NO. SUFFIX KE R(A2110),SH(A2118) TV A2110 / A2118 / SA2151 − SHR(S A2151) SUBJECT Black marking on screen REF No :G A1 031 E0 − − − DATE :30. JUL. 2001 <CONTENTS> Spot remains at power off and black marking may happen on screen.Take the necessary counter...

Page 16 - coutermeasure circuit

1/2 Service Technical Information MODEL NO. SUFFIX TV AN2110 / AN2010 NH / NH − SUBJECT No power on REF No :G A1 040 E0 − − − DATE :24. AUG. 2001 <CONTENTS> No power on due to horizontal output transistor Q601 failure.Take the following countermeasure in this case. <COUNTERMEA SURE> Prev...

Page 17 - WIRING; Be care to the; Be care to the polar; Cushion; of the condenser; FRONT; countermeasure circuit

2/2 WIRING Expansion figure(Pattern Side) <NOTE> Be sure to glue (KE 3490) after putting the semiconductor to the board. − R344 R342 D312 D311 Q412 IC401 HT401 EY64 Q404 Q454 C453 C306 R455 D412 Be care to the Be care to the polar Cushion Wire Resistor direction of diode of the condenser FRONT...

Page 18 - Countermeasure part; PXFM

1/2 Service Technical Information MODEL NO. SUFFIX TV C1400 KY,EZY,KHY − SUBJECT OSD does not display, standby LED does not light REF No :G A1 052 E1 − − − DATE :08. NOV. 2001 REVISION : Mo d i f i ed Ser . No . h ad c o r r ec t ed . <CONTENTS> It may happen that " OSD does not display, s...

Page 20 - count er measure; EXT

1/1 Service Technical Information MODEL NO. SUFFIX TV C1300 / S1311 / S2011 / CN140 U − TV AN145 / AS145 / AS205 / AS215 / CN140 NH − SUBJECT Power off REF No :G A1 053 E0 − − − DATE :20. SEP. 2001 <CONTENTS> Power may off automatically due to the malfunction of 12 PIN (EXT terminal) ofIC 1(mi...

Page 21 - Add

1/1 Service Technical Information MODEL NO. SUFFIX TV C143 / C148 / C1418 KE,KER − TV C208 / C203 / C2018 SH,SHR − SUBJECT Remote controller does not works properly REF.No. :G A1 057 E0 − − − DATE :17. OCT. 2001 <CONTENTS> Due to malfunction of sensor part of remote controller(IC3), it may doe...

Page 27 - Remove the JW606 and JW608 which connect the GND traces.

2/2 1.Replace the FB830 and FB831 of the secondary stage of the power supply to the jumper wire. fig.2 2.Remove the JW606 and JW608 which connect the GND traces. fig.3 3.Replace the JW801 at the primary stage of the power circuit to the ferrite beading. fig.4 3 1 2 MAIN C.B pattern side Front PT801 ...

Page 43 - The diode is already in place on models with Ser i al No .S

2/2 3. Put a zener diode (ZENER, MTZJ9, 1C) in place between the 4th and 8th pins of the EEPROM (be careful to install it in the properdirection). ∗∗∗∗ ∗∗∗∗∗ The diode is already in place on models with Ser i al No .S 9C or later. 1 4 8 5 C7 IC 3 D 9 http://getMANUAL.com