Aiphone 0311 A OI - Manuals

Page 2 - PRECAUTIONS; WARNING; (Negligence could result in injury to people or damage to; General Precautions; General Prohibitions

- 2 - PRECAUTIONS WARNING (Negligence could result in death or serious injury.) 1. The units must be installed and wired by a qualiﬁed technician. Having installation performed by an unqualiﬁed technician could result in electric shock. 2. Do not dismantle or alter the unit. Fire or electric shock c...

Page 3 - Table of Contents; SYSTEM CONFIGURATIONS

- 3 - Table of Contents 1 SYSTEM CONFIGURATIONS Standard system conﬁguration ........................................................................................................................4Expanded system conﬁguration diagram .................................................................

Page 4 - Common area; SYSTEM CONFIGURATIONS; Standard system configuration

- 4 - This system is constructed with a 2-line communication system and a 2-line video system and requires minimal work for installation. The system is constructed with video trunk lines consisting of a maximum of 6 trunks from the video bus control system and communication trunk lines that use a di...

Page 5 - Expanded system configuration diagram; The wiring of the sub trunk line is the same as the standard system.

- 5 - #6 #1 #2 #3 #4 #5 #6 #1 #2 #3 #4 #5 #6 #1 #2 #3 #4 #5 #6 #1 #2 #3 #4 #5 PS-2420, PS-2420S, PS-2420UL PS-2420DIN PS24 2 B A C 3 E D F 5 K J L 8 U T V 4 H G I 6 N M O 1 0 9 Y X W Z 7 R Q P S 2 B A C 1 7 R Q P S 0 3 E D F 4 H G I 5 K J L 6 N M O 8 U T V 9 Y X W Z PS24 PS24 2 B A C 3 E D F 5 K J L...

Page 6 - Mixing on the same trunk line is not possible.; Residential station configuration

- 6 - Audio signal line (1)Video signal line (1)Power supply line (1) 4-way video junction unitGT-4Z 4-way video junction unitGT-4Z Trunk line #1 Each residence Each residence Each residence Each residence Each residence Each residence Each residence Each residence Each residence Each residence Each...

Page 7 - AIPHONE

- 7 - PS24 AIPHONE JF-DVF JK-DA JK-DV JK-DVF PS24 Master monitor station (with recording function)GT-2C-L, GT-2C Residential monitor stationGT-1C-L, GT-1C Sub master monitor stationGT-2H-L, GT-2H Residential monitor station with handsetGT-1M-L Residential stationGT-1D Residential stationGT-1A Each r...

Page 8 - Wiring distance

- 8 - 2 B A C 1 7 R Q P S 0 3 E D F 4 H G I 5 K J L 6 N M O 8 U T V 9 Y X W Z 2B A C 3E D F 5K J L 8U T V 4H G I 6N M O 1 0 9 Y X W Z 7 R Q P S 2 B A C 1 7 R Q P S 0 3 E D F 4 H G I 5 K J L 6 N M O 8 U T V 9 Y X W Z 2B A C 3E D F 5K J L 8U T V 4H G I 6N M O 1 0 9 Y X W Z 7 R Q P S PS24 PS24 PS24 PS2...

Page 10 - COMPONENTS

- 10 - 2 COMPONENTS Entrance Station (Unit type) 2-1 Panel Module Speech module panel (guidance-enabled type) GT-DP-L Speech module (guidance-enabled type) GT-DA-L (connector included) Speech module panel GT-DP Speech module GT-DA (connector included) Camera module panel GT-VP Camera module GT-VA (c...

Page 12 - Bus control unit etc.

- 12 - Video bus control unit GT-VBC Expanded bus control unit GT-BCX (mounting bracket included) Power supply PS-2420DIN Bus control unit GT-BC External signaling relay GT-RY Power supplyPS-2420, PS-2420S,PS-2420UL Wood mounting screws Special screwdriver English, French installation manual • Insta...

Page 14 - MOUNTING; Mounting locations

- 14 - 3 MOUNTING Mounting locations Appropriate cable 3-1 3-2 • For video entrance stations and video door stations, the picture quality of residential station monitoring is affected by the nature of the external light from above and the surrounding area of the built-in cameras, so do not install t...

Page 15 - Mounting positions and image view area; An area over a range of approx. 170

- 15 - Mounting positions and image view area 3-3 When using the camera module, if the rain hood is attached a portion of it will show up in the camera display. (with mounting position of 1350 mm (4'4")) Zoom picture Up/Down Left/Right Objects appear smaller due to greater distortion in the surr...

Page 16 - Options; Back box assembly dimensions

- 16 - Entrance Station (Unit type) 3-4 1 Make a hole for the cable. 2 Use the joint pipe to assemble the back box. • Make sure the back box is mounted level. 1 2 Joint pipe Joint pipe Back box Options Rain hood GT-203H Surface-mount box GF-203BA Hooded surface-mount box GT-203HB 80 cm (32") con...

Page 17 - Remove the terminal cover.; Make sure to run the cable under the terminal cover for protection.; Example of interconnection of modules

- 17 - GT-DA-L/GT-DA 1 0 3 ON 1 2 3 4 CN2 CN1 6 CN2 CN1CN2 CN1CN2 CN1 CN2 CN1 CN2 CN1 8 9 GT-DA-L/GT-DA 1 0 3 ON 1 2 3 4 CN2 CN1 10 11 GT-SW GT-AD 6 Remove the terminal cover. 8 Connect the connectors between the modules with cables. Mount modules on the back boxes. 9 Run the connection cable throug...

Page 19 - Bus control unit, 4-way video junction unit and power supply; DIN rail mounting; Use the wall mounting screws to mount the unit to a wall surface.; Mount the unit on the DIN rail. Click the unit into place.; * When the system does not operate properly, check the wiring.

- 19 - Bus control unit, 4-way video junction unit and power supply 3-6 DIN rail mounting The length of the connecting cable between the GT-BCX and GT-VBX is 40 cm. Therefore, mount them adjacently to each other. Direct mounting to wall surfaces Use the wall mounting screws to mount the unit to a wa...

Page 20 - Surface wiring; Residential station; Optional handset

- 20 - Surface wiring * When a 3-gang box is not mounted, the cable can be routed as surface wiring to the top or bottom of the unit. Cut a cable inlet on the upper part of the unit to allow passage of the wiring into the unit. If there is a large amount of wiring, strip away the jacket of the cable...

Page 21 - Mount the station unit to the mounting bracket.

- 21 - 3 1 Mount the mounting bracket on the 1-gang box or round back box. 2 Connect the wiring to the terminal block. • To remove the terminal block, slide the terminal block and pull it out.• Strip away the jacket of the cable and insert all wires into the slots in an orderly fashion. Failure to d...

Page 22 - Door station; Mount the station unit to the chassis or mounting bracket.; Loosen the screws and remove the mounting frame and main unit.

- 22 - Door station 3-8 For door stations other than the GT-D, see the included instructions. 1 Mount the station unit to the chassis or mounting bracket. 2 Connect the wiring to the terminal block. GT-1M-L:• To remove the terminal block, slide the terminal block and pull it out.• Strip away the jac...

Page 23 - Security guard station; Peel off the protection film on the display.; Wall mounting

- 23 - GT-MK Security guard station 3-9 Peel off the protection ﬁlm on the display. Desk-top mounting using the GFW-S stand Wall mounting 1 Mount the mounting bracket on the 1-gang box or round back box. 2 Connect the wiring to the terminal block. • To remove the terminal block, slide the terminal b...

Page 24 - WIRING; Standard system for common area; VIGIK; VIGIK

- 24 - 4 WIRING Standard system for common area 4-1 #4 #5 #1 #2 GT-MK GT-DMV/GT-DM PS24 AC AC AC/DC AC NP PT PT R1 R2 R1 R2 C CE + - R1 R2 R1 R2 C CE + - 2 B A C 3 E D F 5 K J L 8 U T V 4 H G I 6 N M O 1 0 9 Y X W Z 7 R Q P S 2 B A C 1 7 R Q P S 0 3 E D F 4 H G I 5 K J L 6 N M O 8 U T V 9 Y X W Z GT...

Page 25 - Bus control unit

- 25 - A1 A2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 + - A1 A2 A1 A2 A1 A2 A1 A2 IN1 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 IN2 IN3 IN4 IN5 A1 A2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 + - A1 A2 A1 A2 A1 A2 A1 A2 IN1 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 IN2 IN3 IN4 IN5 R1 R2 + - GT-VBC GT-BC 4 5 2 3 1 9 10 7 8 6 SW2 EXP S...

Page 26 - power supply off and on again.

- 26 - Standard system for residence (station-to-station wiring) 4-2 GT-VBC GT-BC GT-1C-L GT-1C GT-1M-L GT-1A GT-1D GT-2C-L GT-2C GT-2C-L GT-2C GT-2C-L GT-2C GT-2H-L GT-2H #1 #2 #3 GT-2H-L GT-2H PS24 AC PS24 AC PS24 AC JK-DA JK-DV JK-DVF GT-D PS24 + - 100V - 240V - 50/60 Hz 24V DC 2 A PS-2420 PS-242...

Page 27 - Standard system for residence (homerun wiring)

- 27 - Standard system for residence (homerun wiring) 4-3 OUT(2) OUT(4) B1 B2 R1 R2 B1 B2 R1 R2 IN LINE OUT B1 B2 R1 R2 B1 B2 R1 R2 OUT(1) OUT(3) B1 B2 R1 R2 B1 B2 R1 R2 SW1 A B OUT(2) OUT(4) B1 B2 R1 R2 B1 B2 R1 R2 IN LINE OUT B1 B2 R1 R2 B1 B2 R1 R2 OUT(1) OUT(3) B1 B2 R1 R2 B1 B2 R1 R2 SW1 A B GT...

Page 28 - Expanded system

- 28 - Expanded system 4-4 2 3 1 7 8 4 5 9 10 6 PS24 AC GT-VBX GT-BCX R1 R2 + - A2 A1 R1 R2 + - A2 A1 R1 R2 + - A2 A1 R1 R2 + - A2 A1 R1 R2 + - R1 R2 R1 R2 R1 R2 + - R1 R2 + - A2 A1 GT-MK GT-DMV/GT-DM #7 #8 #2 #1 #1 #2 #3 R1 R2 + - A2 A1 R1 R2 + - A2 A1 R1 R2 + - A2 A1 #4 #5 #6 PS24 AC R1 R2 + -...

Page 30 - Option connector; Expanded video bus control unit GT-VBX

- 30 - Option connector 4-5 GT-2C-LGT-2C GT-1C-LGT-1C DCDCRYRYSWSW GT-1M-L GT-MK GT-1A GT-1D KE C K CERY RY SWSW KKERYRYSWSWS1S1ES2S2ES3S3E V+V- DCDCRYRYSWSW DCDCRYRYSWSW SWSW RYRY 2B A C 3E D F 5K J L 8U T V 4H G I 6N M O 1 0 9 Y X W Z 7 R Q P S Emergency alarm Emergency alarm (JP1 is cut during us...

Page 31 - External signaling relay connection

- 31 - External signaling relay connection 4-6 * When the GT-RY is connected, the separate option connecter (4-5) is re- quired. GT-RY contact speciﬁcation: AC/DC 24 V, 0.5 A AC B GT-RY Lead wire (blue) Lead wire (orange) Timer relay (not included) Buzzer Entrance light Lead wire (white) Lead wire (...

Page 32 - Setting list

- 32 - 5 SETTINGS (COMMON AREA) Perform the following settings at an entrance station or security guard station.Depending on the setting item, some items are set by switching DIP switches and some are set using the program mode menu. After any DIP switches are switched or any changes are made in the...

Page 33 - Program Mode; Setting method; Check on the display that the unit is in the standby mode.

- 33 - GT-NS-V/GT-NS GT-DMV/GT-DM SELECT LANGUAGE SELECT LANGUAGE MENU :ENTER SELECT LANGUAGE GUIDE LANGUAGE CHANGE ID CODE GT-MK ● Program Mode Setting method 5-2 Settings can be performed with the GT-NS-V/GT-NS, GT-DMV/GT-DM, and the GT-MK. Programming cannot be performed from a security guard sta...

Page 34 - Changing the ID code; Entrance station and security guard station ID setting

- 34 - GT-NS-V/GT-NS GT-DMV/GT-DM GT-MK SW1 1 2 3 4 1 ON SW1 1 2 3 4 1 ON 4 ON SW2 1 2 3 4 2 B A C 3 E D F 5 K J L 8 U T V 4 H G I 6 N M O 1 0 9 Y X W Z 7 R Q P S Before performing settings, it is recommended that users register an ID code so that other people cannot access the system. ● Enter the p...

Page 35 - Programming with a PC; Writing resident information; Enter a room number using 1 to 6 digits.; PC

- 35 - If the entrance station is a 10 key type or a GT-MK, program the resident information (names and room numbers) before performing the system settings.Up to 500 resident information entries can be registered. ● Programming with a PC • You can use a PC to enter data and write in or change reside...

Page 36 - Manual setting of residence IDs; Change the decimal notation IDs to binary IDs to set the resi-; setup tool and perform settings as shown below.; Create a correlation table with the setup tool between the IDs; Setting up the system

- 36 - Residential station IDs are automatically assigned during link setting. However, with the GT-2C-L/GT-2C and GT-1C-L/GT-1C units only, they can be set manually using the switches on the unit. All are set to OFF in the initial settings.When replacing a residential station due to malfunction, re...

Page 37 - Performing settings from an entrance station; Check that all units are mounted and wired correctly, and then; The corresponding communication channel will be established.

- 37 - ON ON OFF GT-BC 1 4 3 GT-SW Beep 5 GT-NS-V/GT-NS GT-DMV/GT-DM Beep Beep 101 SMITH 101 SMITH ● Performing settings from an entrance station 1 Check that all units are mounted and wired correctly, and then turn on the power switch of the GT-BC. 2 With the GT-DA/GT-DA-L, loosen the base screw of...

Page 38 - Press the OFF button to finish programming. With the handset; The in use LED will go out.; Erasing links

- 38 - 6 Press the OFF button to ﬁnish programming. With the handset type module, return the handset. Repeat steps 3 to 6 to program all residential stations. 7 Press the program switch of the GT-DA-L/GT-DA to ﬁnish programming. The in use LED will go out. For the GT-DMV/GT-DM, press the button. Aft...

Page 39 - Performing settings from a security guard station

- 39 - 1 Check that all units are mounted and wired correctly, and then turn on the power switch of the GT-BC. 2 Enter the program mode at the GT-MK and select "PRO- GRAMMING" from the menu. Wait until "CONNECTING..." is displayed. 3 Lift the handset of the GT-MK. 4 Press and hold do...

Page 40 - Transferring link information

- 40 - Transfer link setting information set at an entrance station or security guard station to other entrance stations and security guard stations. ● Enter the program mode and select "TRANSFER DATA". Transferring link information 5-8 Enter an entrance station number (1 to 16) for the tran...

Page 41 - Performing settings from an entrance station (Unit type); Link check; Select the room and press the button.

- 41 - GT-DA-L/GT-DA ● Performing settings from an entrance station (Unit type) ● Performing settings from an entrance station (Integrated type), security guard station Link check 5-9 Press the program switch of the GT-DA-L/GT-DA for at least 5 seconds.The in use LED will light up after blinking. GT...

Page 42 - celled. The initial setting is 60 seconds.; Setting the input timeout timer; Set the operation timer in the range from 15 to 99 seconds.

- 42 - ● Enter the program mode with the GT-NS-V/GT-NS, GT-DMV/GT-DM or GT-MK and select "SET TIMER". • Operation timer: If the operation panel is not operated for a certain period of time, the system returns to standby mode. The initial setting is 15 seconds. • Program timer: If an operatio...

Page 44 - Setting messages and the standby screen; Select from the following in the standby screen display.; NS

- 44 - GT-DMV/GT-DM MENU :ENTER STANDBY SCREEN BRIGHTNESS SORT SETTING STANDBY SCREEN GREETING OPERATION PICTURE :ENTER ● GT-NS-V/GT-NS: Use 3 of SW1 to change the greeting message to an operation message. The initial setting is for a greeting message. ● GT-DMV/GT-DM: Start the program mode and sele...

Page 46 - Setting the sort order for searching

- 46 - Select either name order or room number order for searching at entrance stations and security guard stations. The initial setting is name order. ● GT-NS-V/GT-NS, GT-DMV/GT-DM, GT-MK: Enter the program mode and select "SORT SETTING". Setting the sort order for searching 5-16 GT-NS-V/GT...

Page 47 - * Setting the access code number of digits; Access code setting; Set the number of digits in the range from 4 to 6.

- 47 - Up to 500 access codes can be set for door release at an entrance station.The number of digits for access codes can be set anywhere in the range from 4 to 6. The initial setting is 4 digits. * Setting the access code number of digits GT-NS-V/GT-NS, GT-DMV/GT-DM: Enter the program mode and s...

Page 48 - Entrance monitor setting

- 48 - GT-VA SW1 ON 1 2 3 4 WIDE ON 1 2 3 4 ZOOM ON 1 2 3 4 ZOOM 3s >> WIDE ON 1 2 3 4 WIDE 3s >> ZOOM Monitoring with the entrance station camera from a residential station can be set to be possible or not possible. The initial setting makes this not pos-sible. ● GT-DA-L/GT-DA: Switch t...

Page 49 - and; Surveillance camera switching setting

- 49 - Select "LIGHT CONTROL" or "CCTV SWITCH" for the operation performed when the light button on a residential station is pressed. The initial set-ting is OFF ("LIGHT CONTROL"). ● GT-VA: Switch this setting with 2 of SW1. Screen brightness can only be adjusted with the GT-...

Page 50 - Select whether calls are transferred or not transferred.; Security guard station transfer setting; direction that the person approaching is facing.; LCD operation mode setting

- 50 - Perform settings for whether calls to security guard stations and emergency alarms are transferred from the RY-RY terminal. The initial settings are for calls and alarms to be transferred. ● GT-MK: Enter the program mode and select "OPTIONAL OUTPUT". Select whether calls are transferr...

Page 51 - Setting using an entrance station 10 key; Entrance zoom picture pre-set; Loosen the base screw of the frame and open and remove the

- 51 - GT-DA-L/GT-DA GT-DA-L/GT-DA The picture can be set to display at the position set for zoom picture display when a residential station is called from an entrance station. The initial set-ting is for display at the center.Perform this setting in the pre-set mode. In the case of direct select ty...

Page 52 - Quit the pre-set mode

- 52 - Setting using a residential station (limited to stations with a zoom/wide function) The picture can be set to display using a set zoom picture position for when a call is received from an entrance station.When switching from the wide screen to the zoom screen, the zoom screen displays startin...

Page 53 - The in use LED will blinks.; beep will be emitted once.; One of the call buttons on the GT-SW can be set as the light button.; Direct select type light button setting

- 53 - 1 Loosen the base screw of the speech module and open and remove the front panel. 2 Remove the rubber cap and use a ﬁne screwdriver to push the setting switch. The in use LED will blinks. 3 While the in use LED is blinking (approximately 15 seconds), press the call button to assign it as the ...

Page 54 - MENU] button in accordance with the warning screen.; MENU] button to complete the; To finish changing settings, press the [

- 54 - 6 Setting (GT-2C-L/GT-2C) How to use the MENU Security guard station settings 6-1 6-2 1 In the standby mode, press the [ ADJUST] button and [ ZOOM/WIDE] button until the warning screen displays. Press the [ MENU] button in accordance with the warning screen. 1 After performing steps 1 in sect...

Page 55 - Emergency input settings; MENU] button to complete the settings; Set emergency input to be enabled or disabled.

- 55 - ALARM INPUT N/O N/C DISABLE EXTERNAL INPUT SETTING SENSOR 2 SENSOR 3 SENSOR 1 SENSOR1 SETTING UTILIT Y SE C URIT Y D ISA B LE Emergency input settings External input setting 6-3 6-4 1 After performing steps 1 in section 6-1, select "ALARM IN- PUT" in the "INSTALLATION" screen ...

Page 56 - MENU] button to complete

- 56 - UTILITY-SENSOR DETECTION METHOD N/C N/O SECURITY-SENSOR DETECTION METHOD N/C N/O EXTERNAL INPUT SETTING SENSOR 2 SENSOR 3 ALARM TRANSFER SENSOR 1 SECURITY ALARM TRANSFER DISABLE NO TRANSFER FOR UTILITY ALARM ENABLE Utility sensor setting (detection method) 4 When "UTILITY" is selected...

Page 57 - Doctor call setting; Set press-to-talk during communication to be enabled or disabled.

- 57 - DOCTOR CALL DISABLE ENABLE PRESS TO TALK DISABLE ENABLE Doctor call setting Press-to-talk setting 6-5 6-6 1 After performing steps 1 in section 6-1, select "DOCTOR CALL" in the "INSTALLATION" screen and press the [ MENU] button. Set press-to-talk during communication to be ena...

Page 58 - Initializing; cancel initialization and return to the previous screen.; TECHNICAL PRECAUTIONS

- 58 - INITIALIZE RETURNING TO DEFAULT ? THIS OPERATION CANNOT BE CANCELED. NO YES Initializing 6-7 All settings can be restored to their condition at the time of purchase. 1. Recorded pictures are erased and settings are reset. 2. Pre-set functions are not reset. Settings reset with "Restor def...