Agilent SMPTE 310M - Manuals

Page 3 - ISM 1—A

i Certification Agilent Technologies certifies that this product met its published specifications at the time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology (form...

Page 7 - Right

pag e in ner mar g in h ang in g c o lu m n ri g h t m argi n b ody te xt le ft m a rg in body text bottom margin footer rulling line footer text base line ou ter mar g in for text a n d a rtwork Right body text drop top margin for modules Contents–1 Contents Introduction ..............................

Page 9 - Introduction

1 Introduction Introduction The E6292A SMPTE (Society of Motion Picture and Television Engineers) 310M interface is serial-to-parallel converter that receives a synchronous serial SMPTE signal and converts it to a DVB-Synchronous Parallel Interface (DVB-SPI) signal. This DVB-SPI signal is then outpu...

Page 10 - Location

Introduction 2 For more help... If you have any questions about the installation procedure, call your local HP representative. You can also contact digital video customer support at the following numbers: If you prefer to email your question, please write to digital video customer support at this ad...

Page 11 - MPEGscope Plus and MPEGscope Lite

3 MPEGscope Plus and MPEGscope Lite MPEGscope Plus and MPEGscope Lite This section explains how to install the SMPTE 310M interface into the MPEGscope Plus or Lite models. Normally, you will install the interface into slot 3, the optional line interface slot. If you have a different MPEGscope PC tha...

Page 12 - Step 1: Remove the cover

MPEGscope Plus and MPEGscope Lite 4 Step 1: Remove the cover WA R N I N G Never remove the computer cover without first removing the power cord from the power outlet and any connection to a telecommunications network. 2 Unplug the AC power cord from the rear of the PC. 3 If you are connected to a te...

Page 14 - Step 2: Remove optional interface

MPEGscope Plus and MPEGscope Lite 6 Step 2: Remove optional interface Complete this step if your MPEGscope already has an optional interface installed and you want to replace it with the SMPTE 310M interface. For an alternative card configuration, refer to page 9. 1 Attach the antistatic wrist strap...

Page 16 - Step 3: Install SMPTE interface

MPEGscope Plus and MPEGscope Lite 8 Step 3: Install SMPTE interface 1 Attach the antistatic wrist strap to your wrist and to the PC chassis as described in the instructions on the envelope. Ensure that the copper foil end of this strap attaches to an electrical ground. IMPORTANT: 2 Install the SMPTE...

Page 18 - Step 4: Replace the cover

MPEGscope Plus and MPEGscope Lite 10 Step 4: Replace the cover 1 Ensure that the two latches on the front sides of the cover are lifted up. 3 Lower the two latches on the front sides of the cover into place. 4 Reconnect your mouse, keyboard, display, power cables, and LAN connection, then power on y...

Page 20 - MPEGscope Portable and Portable Lite

MPEGscope Portable and Portable Lite 12 MPEGscope Portable and Portable Lite This section explains how to install the SMPTE 310M interface into the MPEGscope Portable or Portable Lite models. You will install the interface into slot 2, the optional line interface slot, illustrated below. slot 1—Real...

Page 28 - Connecting to the SMPTE 310M interface

Connecting to the SMPTE 310M interface 20 Connecting to the SMPTE 310M interface DVB–SPI IN/OUT SM PTE 3 10M E6292A IN OUT 5 Connect the input line from your system under test to the IN port on the SMPTE 310M interface. 3 Connect the single SCSI 50-pin connector on the DVB-SPI Y-Adapter cable to the...

Page 29 - Configuring the software

21 Configuring the software Configuring the software Because the SMPTE 310M interface receives and transmits data via the MPEGscope SPI interface, you do not need special SMPTE 310 interface software. You can set receiver and transmitter options from the SPI interface application, as illustrated bel...

Page 32 - SMPTE 310M interface specifications

SMPTE 310M interface specifications WA R N I N G To ensure the Electromagnetic Compatibility (EMC) of MPEGscope, use shielded cables on all interfaces. Type Biphase mark Maximum line rate 40 Mb/s(Minimum receive and transmit rate is 16 Mb/s) Timestamps Packet timestamp clock: 10 MHz +/- 5 ppmResolut...

Page 33 - Release Notes

25 Release Notes Release Notes This section describes two SMPTE 310M interface constraints that may affect your test. It includes a description of the problem along with a simple solution or workaround. Initial startup with sparse streams Upon initial startup or when you make a large bit rate change...